Delta 33-890 - Manual - manualsarea.com

Page 2 - GENERAL SAFETY RULES

2 GENERAL SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain hazards involved with the operation of the product. Using the machine with respect and caution willconsiderably lessen the possibility of personal inj...

Page 4 - GROUNDING INSTRUCTIONS

4 POWER CONNECTIONS A separate electrical circuit should be used for your tools. This circuit should not be less than #12 wire and should beprotected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching recept...

Page 5 - EXTENSION CORDS; OPERATING INSTRUCTIONS; FOREWORD; UNPACKING AND CLEANING; NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord whichhas a 3-prong grounding type plug and matching receptacle which will accept the tool’s plug. When using an extensioncord, be sure to use one heavy enough to carry the current of the too...

Page 6 - OPERATING CONTROLS

6 OPERATING CONTROLS The following is an explanation of the operating controls of the Delta 10” Radial Saw. We suggest you study theseexplanations carefully to familiarize yourself with the controls before turning on the power, to avoid damage to the sawor personal injury. A – TRACK ARM CLAMP KNOB. ...

Page 7 - ASSEMBLY

7 ASSEMBLY Fig. 4A ASSEMBLINGSTEEL LEGS TO BASE Carefully support the machine to the rear and brace theframe so the machine is balanced. Attach the four steellegs to each end of the base using sixteen 5/16-18x5/8"carriage head screws (A) Fig. 4A and Fig. 4B, 5/16" flatwashers (B), 5/16" ...

Page 15 - OPERATING CONTROLS AND ADJUSTMENTS

15 OPERATING CONTROLS AND ADJUSTMENTS Every Delta Radial Saw is thoroughly tested, inspected and accurately aligned before leaving the factory, and whendelivered is ready for operation after it is assembled. However, regardless of the care with which this or any piece offine machinery is manufacture...

Page 16 - ADJUSTING TRACK RODS

16 Fig. 39 Fig. 40 Fig. 41 ADJUSTING CUTTINGHEADBALL BEARINGS AGAINSTTRACK RODS The carriage is mounted on four pre-loaded,prelubricated, shielded ball bearings: two on fixed shafts(on saw blade side of track arm); the other two onadjustable eccentric shafts. The ball bearings must ride smoothly and...

Page 22 - OPERATIONS

22 Fig. 60 ASSEMBLING ACCESSORY33-967 MOULDINGCUTTERHEAD GUARD To assemble the accessory 33-967 Moulding CutterheadGuard to your Radial Arm Saw, proceed as follows: 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Remove blade, and blade guard assembly. 3. Move motor so that the arbor is in the down positio...

Page 25 - PUSH STICK; CONSTRUCTING A PUSH STICK

25 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HAND FROM SLIPPING 1/2" SQUARES CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a p...

Page 26 - NOTES

Page 27 - Two Year Limited Warranty; PARTS, SERVICE OR WARRANTY ASSISTANCE

27 Two Year Limited Warranty Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory whichin normal use has proven to be defective in workmanship or material, provided that the customer returns the productprepaid to a Delta factory servic...

Page 28 - DELTA SERVICE CENTERS; CANADIAN PORTER-CABLE

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): BAMMER ® , INNOVATION THAT WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PORTA-PLANE ® , PORTER- CABLE ® , QUICKSAND ® , SANDTRAP ® , SAW BOSS ® , SPEE...

Delta 33-890 - Manual

Table of Contents:

Summary

Other Delta Models