Delta 36-650 - Manual

10 INSTALLING SWITCHAND MOTOR CORD 1. Insert switch cord (A) Fig. 13, and motor cord (B) of the switch assembly into the opening (C) under sawtable as shown, and into the inside of the saw cabinetFig. 14. 2. Insert switch cord (A) Fig. 14, and motor cord (B) into clamps (D) and loosely fasten both c...

16 10. Using a straight edge, check to see if the saw bladeis aligned with the rear of the splitter (G), as shown inFig. 37. If alignment is necessary, loosen the screws (A)Fig. 37, align splitter (G) with the saw blade, and tightentwo screws (A). 11. Lower saw blade and install table insert (P) Fig...

18 3. Lower the front of rip fence (B) Fig. 46, onto the front guide rail (L). 4. Lock the rip fence (B) Fig. 46, on the guide rails by pushing down handle (A). RIP FENCE TO GUIDE RAILS 1. Insert end cap (A) Fig. 45, into back of rip fence (B). 2. With the fence handle (A) Fig. 46, in the raised pos...

19 LOCKING SWITCH INTHE “OFF” POSITION IMPORTANT: When the tool is not in use, the switch (B) Fig.56, should be locked in the OFF position using apadlock (C), with a 3/16" diameter shackle to preventunauthorized use. STARTING ANDSTOPPING SAW 1. The on/off switch is located underneath the switch ...

20 RAISING AND LOWERINGTHE BLADE To raise the saw blade, loosen lock knob (A) Fig. 58, andturn the blade raising handwheel (B) clockwise. Whenthe blade is at the desired height, tighten lock knob (A). To lower the blade, loosen lock knob (A) Fig. 58, and turnthe handwheel (B) counterclockwise. NOTE:...

23 ADJUSTING TABLE INSERT DISCONNECT MACHINE FROM POWERSOURCE. Place a straight edge across the table at both ends ofthe table insert as shown in Fig. 68. The table insert (A)should always be level with the table. If an adjustment isnecessary, turn the adjusting screws (B), as needed.Four adjusting ...

24 OPERATIONS Common sawing operations include ripping and crosscutting plus a few other standard operations of a fundamentalnature. As with all power tools, there is a certain amount of hazard involved with the operation and use of the machine.Using the machine with the respect and caution demanded...

25 RIPPING Ripping is the operation of making a lengthwise cutthrough a board, as shown in Fig. 82, and the rip fence (A)is used to position and guide the work. One edge of thework rides against the rip fence while the flat side of theboard rests on the table. Since the work is pushed alongthe fence...

27 USING ACCESSORY DADO HEAD THE BLADE GUARD AND SPLITTER ASSEMBLY CANNOT BE USED WHEN DADOING ORMOULDING AND MUST BE REMOVED OR SWUNGTO THE REAR OF THE SAW. Dadoing is cutting a rabbet or wide groove into the work.Most dado head sets are made up of two outside sawsand four or five inside cutters, a...

28 USING AUXILIARY WOODFACING ON RIP FENCE It is necessary when performing special operations such as moulding to add wood facing (A) Fig.94, to one or both sides of the rip fence, as shown. Thewood facing is attached to the fence with wood screws(B), countersunk and assembled through the holesprovi...

29 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HAND FROM SLIPPING 1/2" SQUARES CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a p...

30 Printed in U.S.A. Two Year Limited Warranty Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory whichin normal use has proven to be defective in workmanship or material, provided that the customer returns the productprepaid to a De...

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX ® , Fly...