Page 3 - Table of contents; Scanning bar codes with the DLL2020-WO
Table of contents Preface i Chapter 1 The DLL2020-WO 1 1.1 Unpacking the DLL2020-WO 2 1.2 Scanning bar codes with the DLL2020-WO 4 1.3 Scanner labelling 7 1.4 Maintaining the scanner 11 1.5 Controlling the scanner from the POS system 11 Chapter 2 Installing the DLL2020-WO 13 Installing the scanner 1...
Page 4 - Preface
Preface The Datalogic DLL2020-WO is a high performance omni-directional scanner, whichprovides optimal scanning conditions. The DLL2020-WO shares the same quality ofthe GOLDRUSH TM polygon and Scantium decoder chip as Datalogic’s popular Hunter H-3010, Pollux P-4010 and Castor C-5010 scanners. Toget...
Page 5 - Chapter 1
Page 7 - The green LED indicates a good read.
The various parts of the DLL2020-WO are: Sleep mode switch If a sleep mode time-out has been programmed, the scanner can be reactivated by pressing thisswitch. The sleep-mode feature can be program-med by means of the menu labels in theConfiguration Guide. NOTE: The default value for the sleep modet...
Page 8 - Scanning bar codes with the DLL2020-WO
1.2 Scanning bar codes with the DLL2020-WO The DLL2020-WO is an omnidirectional scanner featuring a 4-directionalscan field with a 16-lines scan pattern. Bar codes can easily be read bypresenting them to the scanner. The scan volume is illustrated in thefigure above. The optimal reading zone lies be...
Page 9 - Handsfree scanning by presenting the item to the scanner.
The Dll2020-wo scanner can be used handsfree as well as hand held,e.g.: a) Handsfree scanning by presenting the item to the scanner. b) Bar code labels can also be scanned in hand held mode, by taking thescanner by the handle and hold it in front of the bar code label on theproduct. 1 2 2 1 The DLL2...
Page 10 - You can also hold the scanner without the handle.
c) You can also hold the scanner without the handle. 1 2 6 The DLL2020-WO
Page 11 - Scanner labelling
1.3 Scanner labelling There are four labels on the scanner. The first three labels can be foundon the housing of the DLL2020-WO, as indicated in the figures below. Thefourth label is visible through the scanner window.All the labels have been attached by the manufacturer and should in nocase be remo...
Page 12 - Laser safety
Laser safety English:The DLL2020-WO scanner complies with safety standard IEC 825-1(1993) for a Class 1 laser product. It also complies with U.S. 21CFR1040as applicable to a Class IIa laser product. Avoid long term viewing ofdirect laser light. German:Der Strichcode-Scanner DLL2020-WO entspricht den...
Page 15 - ASCII code; disable; byte is also called:; sleep
1.4 Maintaining the scanner The DLL2020-WO scanner requires little maintenance. Only occasionalcleaning of the scanner window is necessary in order to remove dirt andfingerprints. The scanner can be cleaned during operation. To this end usea non-abrasive glass spray cleaner and a soft lint-free clot...
Page 16 - POS system; Scanner control
POS system Polaris P-7010 Scanner control 12 The DLL2020-WO DLL2020-WO
Page 17 - Chapter 2
Page 18 - Installing the scanner; Follow these steps carefully in order to install the scanner.; NOTES
14 Installing the DLL2020-WO 2.1 Installing the scanner This chapter describes the instructions necessary for installing theDLL2020-WO scanner.Due to many POS systems on the market, a large number ofcommunication cables is available. Make sure that you have the rightcable to connect the scanner to y...
Page 20 - B) Keyboard Wedge direct power
16 Installing the DLL2020-WO B) Keyboard Wedge direct power For those systems which supply electrical power on the keyboardport (minimal requirements: +5 V dc, 250 mA), the following set-upis applicable.Plug the cable with the 10-pin modular jack into the scanner portuntil a firm ‘click’ is heard.Co...
Page 21 - C) RS232 non direct power
Installing the DLL2020-WO 17 C) RS232 non direct power For those systems which do not supply electrical power on theserial port, the following set-up is applicable. Plug the cable with the 10-pin modular jack into the scanner portuntil a firm ‘click’ is heard.Plug the other connector into the splitt...
Page 22 - D) Keyboard Wedge non direct power
18 Installing the DLL2020-WO D) Keyboard Wedge non direct power For those systems which do not supply electrical power on thekeyboard port, the following set-up is applicable. Plug the cable with the 10-pin modular jack into the scanner portuntil a firm ‘click’ is heard.Plug the other connector into...
Page 23 - IMPORTANT
Installing the DLL2020-WO 19 OPEN PROGRAMMING MODE 1. To select the scanner interface (RS232 factory default), scan thefollowing codes:1. Open the scanner Programming Mode by scanning code 12. - Return to RS232 default by scanning code 2 OR - Return to Keyboard Wedge default by scanning code 3 IMPOR...
Page 24 - RETURN TO RS232 DEFAULT; RETURN TO KEYBOARD WEDGE DEFAULT; Programming Mode is closed after scanning this code.
20 Installing the DLL2020-WO RETURN TO RS232 DEFAULT 2. IMPORTANT: Programming Mode is closed after scanning this code. RETURN TO KEYBOARD WEDGE DEFAULT 3. IMPORTANT: Programming Mode is closed after scanning this code. 712345 100100 712345 100131
Page 25 - Appendices; A. Connector types and pin definitions
Appendices A. Connector types and pin definitions B. Technical Specifications C. Troubleshooting
Page 26 - Use approved Datalogic cables only.; Removing the RJ-48 connector
22 Appendices A. Connector types and pin definitions The Dll2020-wo has a dual interface: RS232/Keyboard Wedge. The pindefinition for the scanner port and the connector to be used for the portare shown in the connection diagram below. Connection Diagram PC - CLOCK DESCRIPTION RJ - 48 PCB ( front vie...
Page 27 - B. Technical specifications
Appendices 23 B. Technical specifications Electrical Power supply voltage 100 - 250 V ac, 50/60 Hz DC input to scanner + 5 V dc ± 5%, 250 mA Dual interface RS232/Keyboard Wedge Optical Light source Visible laser diode (650nm) Depth of field 250 mm Scan pattern 4 directions scan field, 16 lines scan ...
Page 29 - Diagnostic Tips
Appendices 25 The scanner is on but a bar code cannot be read. The LED is red. Diagnostic Tips n The scanner window is dirty. Clean the n scanner window as described in the n Maintenance section. n The presented bar code type is not n enabled. Select the bar code type with n the Configuration Guide....
