Datalogic C-BOX 200 - Manual

v C-BOX 200 General View 1 2 3 Figure A 25-pin scanner connector Cover screws (4) Compression connectors 123

vii SAFETY PRECAUTIONS POWER SUPPLY ATTENTION: READ THIS INFORMATION BEFORE INSTALLING THE PRODUCT - This product is intended to be installed by Qualified Personnel only. The C-BOX 200 is intended to be supplied by an NEC Class 2 power source,rated 10-30 V, minimum 0.65 A. See par. 2.4.1 for correct...

DATALOGIC C-BOX 200 General Features - 1 1 GENERAL FEATURES 1.1 DESCRIPTION The C-BOX 200 is a connection box which can be used as an accessory ofthe Datalogic scanners to perform the following functions: • Facilitate the connection of the scanner signals using a spring clamp connector. • Perform a ...

C-BOX 200 DATALOGIC 2 - Installation 2 INSTALLATION 2.1 PACKAGE CONTENTS Verify that the C-BOX 200 and all the parts supplied with the equipment arepresent and intact when opening the packaging; the list of parts includes: 1) C-BOX 200 2) Installation manual 1 2 Figure 2.1 - C-BOX 200 package conten...

DATALOGIC C-BOX 200 Installation - 3 2.2 OPENING THE DEVICE To install the C-BOX 200 or during normal maintenance, it is necessary toopen it by unscrewing the four cover screws: WARNING The C-BOX 200 must be disconnected from thepower supply during this operation. Figure 2.2 - Opening the C-BOX 200 ...

C-BOX 200 DATALOGIC 4 - Installation 2.3 MECHANICAL INSTALLATION The diagram below gives the overall dimensions of the C-BOX 200 and maybe used for its installation. ∅ ∅ mm in Figure 2.3 - Overall dimensions

C-BOX 200 DATALOGIC 6 - Installation 2.4 ELECTRICAL CONNECTIONS AND SETUP The following figure shows the typical layout. The dotted line in the figurerefers to an optional hardware configuration. PC SCANNER System Cables Scanner Auxiliary Interface Figure 2.5 – System layout A PC can be quickly conn...

DATALOGIC C-BOX 200 Installation - 7 2.4.1 Power Supply Power is supplied to the C-BOX 200 through the pins provided on the springclamp connector. The power switch (see Figure 2.6) switches the power supply ON or OFF forboth the C-BOX 200 and the connected scanner. ON OFF S1 Figure 2.6 - Power switc...

C-BOX 200 DATALOGIC 8 - Installation 2.4.2 System Wiring The connection and wiring procedure for C-BOX 200 is described as follows: 1) Open the C-BOX 200 as described in paragraph 2.2. 2) Verify that the C-BOX 200 power switch is off (see Figure 2.6). 3) Unscrew the compression connectors and pass a...

DATALOGIC C-BOX 200 Installation - 9 The C-BOX 200 spring clamp connector pinouts are indicated in the followingtable. Refer to the scanner Installation Manual for details. Pin Name 1, 3, 5 VS 2, 4, 6 GND 7, 8 EARTH GROUND *9, 13 RS485 CABLE SHIELD *10, 14 RS485 REF *11, 15 RTX485+ *12, 16 RTX485- 2...

DATALOGIC C-BOX 200 Installation - 11 2.4.4 Multidrop Address Selection For RS485 half-duplex interface connections, the scanner multidrop addressshould be set using the rotary switches placed inside the C-BOX 200. The valid address range is from 00 to 31. This value is read only at power-on; any ch...

C-BOX 200 DATALOGIC 12 - Installation 2.4.5 RS485 Bus Termination ON S2 OFF Figure 2.11 - Termination resistance switch The switch S2 enables or disables the insertion of the bus terminationresistor for RS485 Half Duplex Multidrop applications. CAUTION In Multiplexer applications the termination res...

C-BOX 200 DATALOGIC 14 - Installation 2.4.7 OM4000 Jumper Settings J1 J2 Figure 2.13 - OM4000 jumpers The jumpers allow connection to the EXT TRIG signals on separate springclamp terminals for applications which use the OM4000 Oscillating Mirror inTrigger Mode. They are used together and they have t...

DATALOGIC C-BOX 200 Installation - 15 2.5 9-PIN SCANNER AUXILIARY SERIAL INTERFACE The scanner auxiliary serial interface available on the internal 9-pinconnector can be used either for configuration through W inHost or for datamonitoring. The details of the connector pins are indicated in the follo...

C-BOX 200 DATALOGIC 16 - Installation 2.6 SCANNER REQUIREMENTS 1) The C-BOX 200 can be connected to the following scanners through the 25-pin connector illustrated in Figure A. DS2100 DS4300 DS2400 DS4600 It is necessary to use RS232 model (X0XX) for DS2100 and DS2400scanner, while DS4300 and DS4600...

DATALOGIC C-BOX 200 Installation - 17 2.7.1 GET/SEND Buttons The C-BOX 200 has two internal function buttons (GET, SEND). Theprocedure to enable the GET/SEND function is the following: 1. Press both the buttons GET and SEND at the same time for at least one second; the warning LED is turned ON. 2. R...

C-BOX 200 DATALOGIC 18 - Installation 2.7.2 LED Indicators Power on Warning Tx Figure 2.15 - LED Indicators The three internal LEDs of the C-BOX 200 (see Figure 2.15) indicate thefollowing: POWER ON (red) indicates the C-BOX 200 is connected to the powersupply and the power switch is ON. WARNING (re...

DATALOGIC C-BOX 200 Technical Features - 19 3 TECHNICAL FEATURES ELECTRICAL FEATURES Power Supply voltage 10 to 30 Vdc Power consumption max. 1.4 W + scanner USER INTERFACE LED indicators Power ON, Warning, Tx (RS485 Multidrop activity) PHYSICAL FEATURES Mechanical dimensions 167 x 115 x 40 mm (6.57...