Cypress 7C185-15 - Manual
Cypress 7C185-15 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – CC; Electrical Characteristics
- Page 4 – Switching Characteristics; Parameter
- Page 5 – Switching Waveforms
- Page 7 – Typical DC and AC Characteristics; AMBIENT TEMPERATURE (; NORMALIZED I
- Page 9 – Package Diagrams
- Page 11 – Document History Page; Description of Change; SZV
8K x 8 Static RAM
CY7C185
Cypress Semiconductor Corporation
•
3901 North First Street
•
San Jose
•
CA 95134
•
408-943-2600
Document #: 38-05043 Rev. *A
Revised September 13, 2002
185
Features
• High speed
— 15 ns
• Fast t
DOE
• Low active power
— 715 mW
• Low standby power
— 220 mW
• CMOS for optimum speed/power
• Easy memory expansion with CE
1
, CE
2
, and OE features
• TTL-compatible inputs and outputs
• Automatic power-down when deselected
Functional Description
[1]
The CY7C185 is a high-performance CMOS static RAM orga-
nized as 8192 words by 8 bits. Easy memory expansion is
provided by an active LOW chip enable (CE
1
), an active HIGH
chip enable (CE
2
), and active LOW output enable (OE) and
three-state drivers. This device has an automatic power-down
feature (CE
1
or CE
2
), reducing the power consumption by 70%
when deselected. The CY7C185 is in a standard 300-mil-wide
DIP, SOJ, or SOIC package.
An active LOW write enable signal (WE) controls the writ-
ing/reading operation of the memory. When CE
1
and WE in-
puts are both LOW and CE
2
is HIGH, data on the eight data
input/output pins (I/O
0
through I/O
7
) is written into the memory
location addressed by the address present on the address
pins (A
0
through A
12
). Reading the device is accomplished by
selecting the device and enabling the outputs, CE
1
and OE
active LOW, CE
2
active HIGH, while WE remains inactive or
HIGH. Under these conditions, the contents of the location ad-
dressed by the information on address pins are present on the
eight data input/output pins.
The input/output pins remain in a high-impedance state unless
the chip is selected, outputs are enabled, and write enable
(WE) is HIGH. A die coat is used to insure alpha immunity.
Logic Block Diagram
Pin Configurations
A
1
A
2
A
3
A
4
A
5
A
6
A
7
A
8
A
0
A
10
A
9
A
11
A
12
I/O
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
V
CC
WE
CE
2
A
3
A
2
A
1
OE
A
0
CE
1
I/O
7
I/O
6
I/O
5
I/O
4
I/O
3
NC
A
4
A
5
A
6
A
7
A
8
A
9
A
10
A
11
A
12
I/O
0
I/O
1
I/O
2
GND
256 x 32 x 8
ARRAY
INPUT BUFFER
COLUMN DECODER
ROW
DE
CODE
R
S
E
N
S
E AM
PS
POWER
DOWN
I/O
1
I/O
2
I/O
3
I/O
4
I/O
5
I/O
6
I/O
7
CE
1
CE
2
WE
OE
Top View
DIP/SOJ/SOIC
Selection Guide
[2]
7C185-15
7C185-20
7C185-25
7C185-35
Maximum Access Time (ns)
15
20
25
35
Maximum Operating Current (mA)
130
110
100
100
Maximum Standby Current (mA)
40/15
20/15
20/15
20/15
Note:
1.
For guidelines on SRAM system design, please refer to the ‘System Design Guidelines’ Cypress application note, available on the internet at www.cypress.com.
2.
For military specifications, see the CY7C185A data sheet.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
CY7C185 Document #: 38-05043 Rev. *A Page 2 of 11 Maximum Ratings (Above which the useful life may be impaired. For user guide-lines, not tested.) Storage Temperature ................................. –65 ° C to +150 ° C Ambient Temperature withPower Applied ............................................
CY7C185 Document #: 38-05043 Rev. *A Page 4 of 11 Switching Characteristics Over the Operating Range [6] 7C185-15 7C185-20 7C185-25 7C185-35 Parameter Description Min. Max. Min. Max. Min. Max. Min. Max. Unit Read Cycle t RC Read Cycle Time 15 20 25 35 ns t AA Address to Data Valid 15 20 25 35 ns t O...
CY7C185 Document #: 38-05043 Rev. *A Page 5 of 11 Switching Waveforms 10. Device is continuously selected. OE, CE 1 = V IL . CE 2 = V IH . 11. WE is HIGH for read cycle. 12. Data I/O is High Z if OE = V IH , CE 1 = V IH , WE = V IL , or CE 2 =V IL . 13. The internal write time of the memory is defin...
