Cisco 7600 - Manual
Cisco 7600 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Front Panel Description; Figure 1; CONSOLE Ports, page 3; LEDs; Table 1; LED
- Page 3 – CONSOLE Ports; System Requirements; These sections describe the hardware and software requirements:; Hardware Components; Table 2; Slot
- Page 4 – Software Requirements; Safety Overview; Number 2 Phillips screwdriver; IMPORTANT SAFETY INSTRUCTIONS
- Page 5 – Installing the WiSM; To install the WiSM in the chassis, follow these steps:; “Removing the WiSM” section on page 13
- Page 6 – Horizontal slots; Figure 4; Tighten the two captive installation screws on the WiSM.
- Page 9 – Vertical slots; Figure 7
- Page 12 – Verifying the Installation; This example shows the output of the show module command:
- Page 13 – Removing the WiSM; To remove a WiSM from the chassis, follow these steps:; Shutdown may require several minutes.; Configuring the WiSM
- Page 14 – Regulatory Standards Compliance; You can access the most current Cisco documentation at this URL:
- Page 15 – Product Documentation DVD; Documentation Feedback; We appreciate your comments.; Cisco Product Security Overview; From this site, you will find information about how to:
- Page 16 – Reporting Security Problems in Cisco Products; For Emergencies only —; The link on this page has the current PGP key ID in use.; Obtaining Technical Assistance
- Page 17 – Cisco Technical Support & Documentation Website; Submitting a Service Request; For a complete list of Cisco TAC contacts, go to this URL:
- Page 18 – Definitions of Service Request Severity; Obtaining Additional Publications and Information
- Page 19 – or view the digital edition at this URL:
Corporate Headquarters:
© 2005–2006 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Catalyst 6500 Series Switch and Cisco 7600
Series Router Wireless Services Module
Installation and Verification Note
Product number: WS-SVC-WiSM-1-K9
This document provides installation procedures for the Catalyst 6500 Series Switch and Cisco 7600
Series Router Wireless Services Module (WiSM).
Contents
This publication contains these sections:
•
Front Panel Description, page 2
•
•
•
•
•
Verifying the Installation, page 12
•
•
Regulatory Standards Compliance, page 14
•
Related Documentation, page 14
•
Obtaining Documentation, page 14
•
Documentation Feedback, page 15
•
Cisco Product Security Overview, page 15
•
Obtaining Technical Assistance, page 16
•
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Catalyst 6500 Series Switch and Cisco 7600 Series Router Wireless Services Module Installation and Verification Note 78-17121-04 Front Panel Description Front Panel Description The Cisco WiSM front panel (see Figure 1 ) includes a POWER LED, two STATUS LEDs, and two CONSOLE ports. Note The Compact...
3 Catalyst 6500 Series Switch and Cisco 7600 Series Router Wireless Services Module Installation and Verification Note 78-17121-04 System Requirements CONSOLE Ports The CONSOLE ports allow you to access each controller either locally (with a console terminal) orremotely (with a modem). The CONSOLE p...
4 Catalyst 6500 Series Switch and Cisco 7600 Series Router Wireless Services Module Installation and Verification Note 78-17121-04 Safety Overview Software Requirements Before you install the WiSM into the chassis, make sure that the module and the chassis meet thesoftware requirements. Refer to the...
