Cisco 7513 - Manual
This Installation Manual covers the upgrade process for the redundant AC-input power supplies in the Cisco 7513 router system, emphasizing safety, compatibility, and redundancy requirements. The manual highlights key topics such as identifying outdated power supply models (e.g., part numbers like 34-0049-01), ensuring proper installation of newer units (e.g., 34-0667-01), and adhering to safety protocols–including grounding, ESD precautions, and preventing mixed AC/DC or old/new supply configurations. It also addresses environmental monitoring, fault thresholds, and troubleshooting via CLI commands like show environment, while detailing operational requirements such as redundant load-sharing and power factor correction features.
Table of Contents:
- Page 1 – Power Supply Upgrade Instructions and Safety Precautions
- Page 2 – Identifying and Upgrading Power Supplies
- Page 3 – Router Rear-Panel Components and Power Supply Location
- Page 4 – Chassis Diagram and Power Supply Configuration
- Page 5 – Power Supply Specifications and Redundancy
- Page 6 – Power Supply LED Indicators and Connectors
- Page 7 – Power Supply Safety Interlocks
- Page 8 – Environmental Monitoring and Shutdown Procedures
- Page 9 – System Shutdown Triggers and Thresholds
- Page 10 – Monitoring Environmental Status via CLI Commands
- Page 11 – Monitoring Power Supply Status and Faults
- Page 12 – Safety Guidelines for Installation and Upgrades
- Page 13 – Tools and Safety for Power Supply Replacement
- Page 14 – Procedure for Replacing Older AC-Input Power Supplies
- Page 15 – Removing an Older Power Supply
- Page 16 – Installing New Power Supplies
- Page 17 – Securing and Connecting New Power Supplies
- Page 18 – Verifying New Power Supply Installation
- Page 19 – Power Disconnection Warning
- Page 20 – Obtaining Cisco Documentation
- Page 21 – Accessing Technical Support and Service Requests
- Page 22 – Technical Support Contact and Severity Levels
- Page 23 – Cisco Publications and Training Resources
- Page 24 – Obtaining Additional Publications and Information
Corporate Headquarters:
Copyright © 2004 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Upgrading the 1200-Watt, AC-Input
Power Supplies in the Cisco 7513
This document contains instructions for upgrading your existing Cisco 7513, 1200-watt (W), alternating
current (AC)–input power supplies, with new AC-input power supplies. (See .) A single power supply is
standard equipment for the Cisco 7513. A second, identical power supply, when installed, provides
redundant power. In systems with redundant power, the power supplies are load-sharing and fully
hot-swappable; you can remove and replace one supply, while the remaining supply immediately ramps
up to full power to maintain uninterrupted system operation.
Caution
The new and older power supplies must not be used simultaneously in the Cisco 7513. The redundant
power, load-sharing feature of the Cisco 7513 requires identical power supplies in each of the two power
supply bays. While no physical damage will occur if two different supplies are installed into a Cisco
7513, there is the possibility of erratic system behavior and error messages.
Note
If your Cisco 7513 contains older AC-input power supplies, Part Number 34-0049-01, or later, use this
document to replace them with new power supplies carrying Part Number 34-0667-01 or later. If you have a
Cisco 7513 with one or two of the older AC-input power supplies, you must replace both of them with the
new AC-input power supplies. All Cisco 7513 chassis must have the new AC-input power supplies installed
in them.
The sections in this document include the following:
•
Determining the Power Supply Model, page 2
•
•
Installation Safety, ESD Precautions, and Tools Required, page 12
•
Replacing Older AC-Input Power Supplies, page 14
•
Checking the New Power Supply Installation, page 18
•
Related Documentation, page 20
•
Obtaining Documentation, page 20
•
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Was this manual helpful?
About this manual
- Brand
- Cisco
- Model
- 7513
- Document type
- Manual
- Language(s)
- English
- Pages
- 24
- File size
- 1.2 MB
- Format
Summary
Instructions for upgrading 1200-watt AC-input power supplies, warnings against mixing old and new supplies, and document structure for installation procedures.
Procedure for identifying and upgrading AC-input power supplies, including part numbers for older and newer models, and verification steps based on labels.
Overview of rear-panel components of the Cisco 7513 router, including the location of optional AC-input power supplies.
