Cisco 6911 - Manual

Cisco 6911

Cisco 6911 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
Page: / 10

Table of Contents:

  • Page 2 – Cisco Unified Communications Manager Configuration; Network and Access Ports
  • Page 3 – Handset
  • Page 4 – Installing the Cisco Unified IP Phone
  • Page 7 – Footstand
  • Page 8 – Higher Viewing Angle
  • Page 9 – Mounting the Phone to the Wall; Verifying the Phone Startup Process; Configuring Startup Network Settings
  • Page 10 – Configuring Security on the Cisco Unified IP Phone
Loading the manual

C H A P T E R

3-1

Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.0 (SCCP)

OL-20852-01

3

Setting Up the Cisco Unified IP Phone

This chapter includes the following topics, which help you install the Cisco Unified IP Phone on an IP
telephony network:

Before You Begin, page 3-1

Understanding the Cisco Unified IP Phone 6901 and 6911 Components, page 3-2

Installing the Cisco Unified IP Phone, page 3-4

Footstand, page 3-7

Verifying the Phone Startup Process, page 3-9

Configuring Startup Network Settings, page 3-9

Note

Before you install a Cisco Unified IP phone, you must decide how to configure the phone in your
network. Then you can install the phone and verify its functionality. For more information, see

Chapter 2, “Preparing to Install the Cisco Unified IP Phone on Your Network.”

Before You Begin

Before installing the Cisco Unified IP Phone, review the requirements in these sections:

Network Requirements, page 3-1

Cisco Unified Communications Manager Configuration, page 3-2

Network Requirements

For the Cisco Unified IP Phone to successfully operate as a Cisco Unified IP Phone endpoint in your
network, your network must meet the following requirements:

Working Voice over IP (VoIP) Network:

VoIP configured on your Cisco routers and gateways

Cisco Unified Communications Manager installed in your network and configured to handle
call processing

IP network that supports DHCP or manual assignment of IP address, gateway, and subnet mask

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Cisco Unified Communications Manager Configuration; Network and Access Ports

3-2 Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.0 (SCCP) OL-20852-01 Chapter 3 Setting Up the Cisco Unified IP Phone Understanding the Cisco Unified IP Phone 6901 and 6911 Components Cisco Unified Communications Manager Configuration The Cisco...

Page 3 - Handset

3-3 Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.0 (SCCP) OL-20852-01 Chapter 3 Setting Up the Cisco Unified IP Phone Understanding the Cisco Unified IP Phone 6901 and 6911 Components Each port supports 10/100 Mbps half- or full-duplex connecti...

Page 4 - Installing the Cisco Unified IP Phone

3-4 Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.0 (SCCP) OL-20852-01 Chapter 3 Setting Up the Cisco Unified IP Phone Installing the Cisco Unified IP Phone Installing the Cisco Unified IP Phone You must connect the Cisco Unified IP Phone to the...

Other Cisco Models

All Cisco Other