Page 2 - Installation Instructions; DISCLAIMER; Site Requirements (WM2XXSI and; and WM2XXS MOUNT MODELS)
WM210-220-230-240S/SI Installation Instructions 2 DISCLAIMER Milestone AV Technologies and its affiliated corporations andsubsidiaries (collectively "Milestone"), intend to make thismanual accurate and complete. However, Milestone makes noclaim that the information contained herein covers al...
Page 3 - DIMENSIONS
Installation Instructions WM210-220-230-240S/SI 3 DIMENSIONS 10.81 7.25 .75 16.00 11.53 .34 7.25 3.96 5.64 210S, TRAVEL 12.75" - 19.5" 240S, TRAVEL 37.2" - 65.6" 3 OF 5.36 19.63 1.42 1.09 CABLE CHANNEL DIMENSIONS THRU ARM DIMENSIONS: INCHES WM2XXS (Standard Model) 10.81 274.64 7.25 1...
Page 4 - LEGEND
WM210-220-230-240S/SI Installation Instructions 4 LEGEND Tighten Fastener Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador ...
Page 5 - TOOLS REQUIRED FOR INSTALLATION; Interactive Models Only)
Installation Instructions WM210-220-230-240S/SI 5 TOOLS REQUIRED FOR INSTALLATION PARTS 1/2" (12.7mm) #2 7/32" (5.6mm) 3/8" (9.5mm) 3/16" (included) 5/32" (included) (security) 1/2" (12.7mm) 5/32" - 6" long (included) (security) D (2) [wall bracket E (2) 1/4-20 x 5/8&...
Page 6 - SITE REQUIREMENTS (WM2XXS; Figure 1
WM210-220-230-240S/SI Installation Instructions 6 SITE REQUIREMENTS (WM2XXS I and WM2XXS Models) - Steel Stud Structure WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for instal...
Page 7 - INTERACTIVE MODEL ONLY; tighten the cap; only; Minimum System Requirements; Ultrasound Reflections; Figure 2; Drawing surface; Motion sensor
WM210-220-230-240S/SI Installation Instructions 7 WS2XXS I INTERACTIVE MODEL ONLY The Chief Interactive Mount (WM2XXS I ) works with standard projectors and Windows® and Macintosh® computers. TheInteractive Mount will transform existing whiteboards or otherhard, flat surfaces, into interactive white...
Page 8 - Placement and Projection Area; Figure 3; Projection
Installation Instructions WM210-220-230-240S/SI 8 WM2XXS I Placement and Projection Area Constraints (See Figure 3) • There should be a minimum distance of 12 inchesbetween the base of the dual mount and the top of theprojection image. • The distance between the base of the dual mount andthe bottom ...
Page 9 - Mounting Wall Bracket; Concrete or Concrete Block; Figure 4; Wood Studs; Adjustments; Figure 6
Installation Instructions WM210-220-230-240S/SI 9 ASSEMBLY AND INSTALLATION - (WM2XXSIand WM2XXS MODELS) The WM-210S/SI, -220S/SI, -230S/SI and -240S/SI short throwprojector mounts can be mounted to concrete, concrete block,wood studs or steel studs. They can be mounted to 2" x 4"wood studs ...
Page 10 - Figure 7; Steel Studs; See; Site Requirements; section before; Figure 8
WM210-220-230-240S/SI Installation Instructions 10 5. Install four 5/16 x 2-1/2" hex head lag screws (L) throughfour 5/16" washers (M), holes of wall bracket and into drilledholes. (See Figure 7) Figure 7 Steel Studs IMPORTANT ! : See Site Requirements section before proceeding with Steel St...
Page 11 - Installation to Wall Bracket
Installation Instructions WM210-220-230-240S/SI 11 10. Place wall bracket over anchors and align mounting holes in display mount with holes in anchors. (See Figure 12) 11. Insert 1/4-20 x 1-3/4" Phillips pan head screws (N) through 1/4" washer (Q), corresponding mounting hole on wallbracket ...
Page 12 - Projector Installation; RPM Installation; or; raise
WM210-220-230-240S/SI Installation Instructions 12 4. Loosen two bolts on either side of pitch adjustment screw.(See Figure 16) 5. Adjust pitch adjustment screw until mount is at desired pitchlevel. Turn clockwise to raise mounting level or turncounterclockwise to lower mounting level. (See Figure 1...
Page 13 - RPA Installation; INTERACTIVE MOUNT; Complete the installation by; WM2XXSI Interactive Mount; section or; WM2XXS Standard Mount
Installation Instructions WM210-220-230-240S/SI 13 RPA Installation 1. Line up mounting holes on RPA mount with correspondingholes on projector mounting plate. (See Figure 17) 2. Install four 1/4-20 x 3/8" Phillips pan machine screws (G)through RPA holes and into projector mounting plate. (SeeFi...
Page 14 - Removing Mount Covers
WM210-220-230-240S/SI Installation Instructions 14 4. Lower the upper cover (X) onto the wall mount and lowercover, and fasten with two 8-32 x 3/8" Phillips pan headscrews (AB). (See Figure 24) NOTE: Be sure cables and cords are not pinched between upper and lower covers. Figure 24 Cable Managem...
Page 15 - Routing Cables from Below (Steps 6 and 7); Proceed to Step 9
Installation Instructions WM210-220-230-240S/SI 15 NOTE: Cables may be routed from below and up wall bracket channel, or from above and down behind and into wallmount. • Routing Cables from Below (Steps 6 and 7) 6. Open cable clips along bottom edge of wall bracket. (SeeFigure 28) Figure 28 7. Threa...
Page 16 - Installation of Wall Bracket Covers
WM210-220-230-240S/SI Installation Instructions 16 10. (Optional) Cables can be tied to inside of mount’s front cover using cable ties (not included). Route cables nearfront cover and wrap cable tie through slots on front coverand around cables. (See Figure 32) Figure 32 11. Replace removed cable ma...
Page 17 - Bracket Width Adjustment; The mount covers need to be removed; Installing Mount Covers; Extension Adjustment
Installation Instructions WM210-220-230-240S/SI 17 Adjustments Bracket Width Adjustment 1. Loosen two flat head cap screws on wall bracket. (SeeFigure 36) 2. Slide wall brackets to corresponding width of studs. (SeeFigure 36) 3. Tighten two flat head cap screws on wall bracket. (SeeFigure 36) Figure...
Page 18 - Lateral Shift Adjustment; Wall Bracket Covers
WM210-220-230-240S/SI Installation Instructions 18 Lateral Shift Adjustment IMPORTANT ! : The mount covers need to be removed before proceeding with lateral shift adjustment. NOTE: Remove mount covers from the mount following instructions in Removing Mount Covers section. 1. Loosen two 1/4-20 x 5/8&...
Page 19 - Stop Bracket
Installation Instructions WM210-220-230-240S/SI 19 3. Remove two 8-32 x 3/8" Phillips pan head screws (AB) fromlower cover. (See Figure 44) Figure 44 4. Install two 8-32 x 3/8" button head security screws (AA) intolower cover. (See Figure 45) Figure 45 5. Replace upper cover and install two ...
Page 20 - Adapter Plate Bolts; one bolt at a
WM210-220-230-240S/SI Installation Instructions 20 2. Install two 1/4-20 x 1/2" button head security screws (T)through holes in stop bracket and into holes in sliding nuts.(See Figure 48) Figure 48 Adapter Plate Bolts 1. Remove projector from short throw projector mountaccording to projector int...
Page 21 - WM2XXS STANDARD MOUNT
Installation Instructions WM210-220-230-240S/SI 21 WM2XXS STANDARD MOUNT Installing Mount Covers 1. Raise the lower cover (AK) to wall mount and hold in place.(See Figure 51) Figure 51 2. Lower the upper cover (AJ) onto the wall mount and fastenthrough upper cover (AJ), lower cover (AK) and into wal...
Page 22 - Routing Cables from Below (Steps 5 and 6); Proceed to Step 8
WM210-220-230-240S/SI Installation Instructions 22 4. Remove cable management covers (if necessary) fromshort throw projector arm. (See Figure 55) Figure 55 NOTE: Cables may be routed from below and up wall bracket channel, or from above and down behind and into wallmount. • Routing Cables from Belo...
Page 23 - Security; (Projector arm not shown
Installation Instructions WM210-220-230-240S/SI 23 8. Route cables through cover mount, projector arm tunneland into projector. (See Figure 59) Figure 59 9. (Optional) Cables can be tied to inside of mount’s front cover using cable ties (not included). Route cables nearfront cover and wrap cable tie...
Page 26 - Mount Covers
WM210-220-230-240S/SI Installation Instructions 26 Mount Covers 1. Remove two #8-32 x 1/2" Phillips pan machine screws (F)holding mount covers on projector arm. (See Figure 71) 2. Install two #8-32 x 1/2" button head security screws (V) intoholes on mount cover. (See Figure 71) Figure 71 Sto...
Page 28 - Europe; Asia Pacific
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845 Asia Pacific A Office No. 1 on 12/F, Shatin Galleria18-24 Shan Mei Street Fota...
