Page 3 - What is included; Icons
1. Before You Begin 3 11/19/2010 11:07 AM 1. B EFORE Y OU B EGIN What is included • 1 x Intimidator™ Scan LED 100 • 1 x Hanging bracket • 1 x Power Cord • 1 x Warranty Card • 1 x User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents ...
Page 4 - Safety Instructions
1. Before You Begin 4 11/19/2010 11:07 AM Safety Instructions • Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. • Always make sure that you are connecting to the proper voltage, and that the line vol...
Page 5 - NTRODUCTION; Product Overview
2. Introduction 5 11/19/2010 11:07 AM 2. I NTRODUCTION Product Overview Power Out Microphone Sensitivity Adjustment knob Microphone Power In DMX Out Safety DMX In DIP Switches Fuseholder Power LED Indicator Signal LED Indicator
Page 6 - ETUP; AC Power; Power Linking
3. Setup 6 11/19/2010 11:07 AM 3. S ETUP AC Power This fixture is auto-ranging and runs on 100~240 VAC, 50/60 Hz power. To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture or refer to the fixture’s specifications chart. A fixture’s lis...
Page 7 - Mounting; Orientation; Rigging
3. Setup 7 11/19/2010 11:07 AM Mounting Orientation The Intimidator™ Scan LED 100 may be mounted in any position provided there is adequate room for ventilation. Rigging Be sure that the structure can support the weight of the fixture. Please see the “Technical Specifications” section of this manual...
Page 8 - Configuring the Starting Address; Operation; DMX Operation
4. Operating Instructions 8 11/19/2010 11:07 AM 4. O PERATING I NSTRUCTIONS Configuring the Starting Address The Intimidator™ Scan LED 100 fixture uses 6 DMX channels. In this DMX configuration/personality, the highest channel that the fixture may be set to in order to function properly is 507 . Any...
Page 9 - Standalone; Automatic
4. Operating Instructions 9 11/19/2010 11:07 AM Standalone This fixture has several options for operating without a DMX controller. These options are accessed via the DIP switches on the back of the fixture. Please see the chart below for further explanation. DIP Switches Function 1 2 3 4 5 6 7 8 9 ...
Page 10 - DMX Channel Values
4. Operating Instructions 10 11/19/2010 11:07 AM Sound-Active Access this mode via the DIP switches on the back of the fixture. The chart on the previous page may be used to alter playback parameters. Please see the instructions below for details on entering this mode. 1. Unplug any DMX controller. ...
Page 11 - PPENDIX; General Troubleshooting
5. Appendix 11 11/19/2010 11:07 AM 5. A PPENDIX General Troubleshooting S YMPTOM P OSSIBLE C AUSE ( S ) P OSSIBLE A CTION ( S ) Breaker/Fuse keeps blowing • Excessive circuit load • Check total load placed on the electrical circuit. • Short circuit along the power wires • Check for a short in the el...
Page 12 - DMX Primer; Data Cabling; DMX Data Cable
5. Appendix 12 11/19/2010 11:07 AM DMX Primer There are 512 channels in a DMX connection. A fixture capable of receiving DMX will require one or a number of sequential channels. The user must assign a starting address on the fixture that indicates the first channel reserved in the controller. There ...
Page 13 - Cable Connectors; Setting the Starting Address
5. Appendix 13 11/19/2010 11:07 AM Cable Connectors Cabling must have a male XLR connector on one end and a female XLR connector on the other end. Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a ground loop, and your fixture may perform erra...
Page 14 - Setting up a DMX Daisy Chain
5. Appendix 14 11/19/2010 11:07 AM 3-Pin to 5-Pin Conversion Chart If you use a controller with a 5-pin DMX output connector, you will need to use a 5-pin to 3-pin adapter. The chart below details a proper cable conversion: 3-P IN TO 5-P IN C ONVERSION C HART Conductor 3-Pin Female (Output) 5-Pin Ma...
Page 15 - General Maintenance; Returns Procedure
5. Appendix 15 11/19/2010 11:07 AM General Maintenance To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build u...
Page 17 - ONTACT; W o r l d W i d e
C ONTACT U S W o r l d W i d e General Information CHAUVET® 5200 NW 108 th Ave Sunrise, FL 33351 voice: 954.929.1115 fax: 954.929.5560 toll free: 800.762.1084 Technical Support CHAUVET® 5200 NW 108 th Ave Sunrise, FL 33351 voice: 954.929.1115 (Press 4) fax: 954.929.5560 (Attention: Service) World Wi...
