Chauvet LED PAR 38 TRI-C - Manual

2. Introduction 6 9/22/2009 11:10 AM Photometrics The photometric readings have been provided at 1 m, 2 m, and 3 m. Below, you will find a 3-dimensional drawing of the beam and field angles, along with lux and beam diameter for the field and beam angles. The lux measurements provided are maximum out...

2. Introduction 7 9/22/2009 11:10 AM Product Overview Power Output Control Panel DMX In Power Input (Hardwired) Power Input (Hardwired) Microphone Audio Adjustment Knob Fuseholder Gel Frame Gel Frame Release Bracket Adjustment Knob Bracket Adjustment Knob Attachment Bolt (not meant to be adjusted) D...

3. Setup 8 9/22/2009 11:10 AM 3. S ETUP AC Power This fixture runs on 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure the line voltage to which you are connecting it is within the range of accepted voltages. Always connect the fixture to a switched circuit. Never connect the fixture to...

3. Setup 9 9/22/2009 11:10 AM Do not use a tool on the bracket adjustment knob Mounting Bracket Secondary bracket (used primarily for standing position) Aim the fixture with the gel frame release pointing up, (as shown in this diagram) Mounting Orientation The LED PAR 38 Tri-B/C may be mounted in an...

3. Setup 10 9/22/2009 11:10 AM Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on...

3. Setup 11 9/22/2009 11:10 AM This drawing provides a general illustration of the DMX input/output panel of a lighting fixture. Universal DMX Controller Continue the link 3-Pin to 5-Pin Conversion Chart If you use a controller with a 5-pin DMX output connector, you will need to use a 5-pin to 3-pin...

4. Operating Instructions 12 9/22/2009 11:10 AM 4. O PERATING I NSTRUCTIONS Configuring the Starting Address Each fixture requires a starting address from 1~512. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the starting address. For example...

4. Operating Instructions 14 9/22/2009 11:10 AM Standalone Operation Automatic This fixture has preprogrammed chases. These are accessed via the control panel, and the speed may be adjusted for the chases. Please see the instructions below for further explanation. 1. Press <MENU> until appears...

4. Operating Instructions 16 9/22/2009 11:10 AM DMX Channel Values 7-CH Mode C HANNEL V ALUE F UNCTION 1 000  255 Red Dimmer: 0%~100% 2 000  255 Green Dimmer: 0%~100% 3 000  255 Blue Dimmer: 0%~100% 4 000  015 016  255 Color Macros (override CH.1~3) No Function Color Macros 5 000  255 Speed (C...

5. Appendix 17 9/22/2009 11:10 AM 5. A PPENDIX DMX Primer There are 512 channels in a DMX connection. Channels may be assigned in any manner. A fixture capable of receiving DMX will require one or a number of sequential channels. The user must assign a starting address on the fixture that indicates ...

5. Appendix 18 9/22/2009 11:10 AM Setting the Starting Address This DMX mode enables the use of a universal DMX controller device. Each fixture requires a start address from 1~512. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start addr...

5. Appendix 19 9/22/2009 11:10 AM Returns Procedure Returned merchandise must be sent prepaid and in the original packing; call tags will not be issued. Package must be clearly labeled with a Return Merchandize Authorization Number (RMA #). Products returned without the RMA # will be refused. Call C...

Technical Specifications 20 9/22/2009 11:10 AM Technical Specifications WEIGHT & DIMENSIONS Length .......................................................................................................................... 9.3 in (235 mm) Width........................................................