Page 3 - What is included; Icons
1. Bef ore You Begin 3 1/12/2011 11:51 AM 1. B EFORE Y OU B EGIN What is included • 1 x Sweeper™ LED • 1 x Power Cord • 1 x W arranty Card • 1 x User Manual Unpacking Instructions Immediately upon receiving a fixture, caref ully unpack the carton, check the contents to ensure that all parts are pres...
Page 4 - Safety Instructions
1. Bef ore You Begin 4 1/12/2011 11:51 AM Safety Instructions • Please keep this User Manual f or future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. • Always make sure that you are connecting to the proper voltage, and that the line vo...
Page 5 - NTRODUCTION; Product Overview
2. Introduction 5 1/12/2011 11:51 AM 2. I NTRODUCTION Product Overview Microphone DMX Out Control Panel (LED display) DMX In Power In Fuseholder Power Linking Out Microphone Adjustment Safety
Page 6 - ETUP; AC Power; Power Linking
3. Setup 6 1/12/2011 11:51 AM 3. S ETUP AC Power This fixture is auto-ranging and runs on 100~240 VAC, 50/60 Hz power. To determine the power requirements f or a particular fixture, see the label affixed to the back plate of the fixture or ref er to the fixture’s specifications chart. A fixture’s li...
Page 7 - Mounting; Orientation; Rigging
3. Setup 7 1/12/2011 11:51 AM Mounting Orientation The Sweeper™ LED may be mounted in any position, provided there is adequate room f or ventilation. Rigging Be sure that the structure can support the weight of the fixture. Please see the “T echnical Specifications” section of this manual for a deta...
Page 8 - Using the Control Panel; Menu Map; Configuring the Starting Address
4. Operating Instructions 8 1/12/2011 11:51 AM 4. O PERATING I NSTRUCTIONS Using the Control Panel Access control panel functions using the f our buttons located directly underneath the LED display. B UTT ON F UNCTION <MODE/ ESC> Used to scroll through the current operating mode, as well as ba...
Page 9 - Operation; DMX Operation; DMX Channel Values
4. Operating Instructions 9 1/12/2011 11:51 AM Operation DMX Operation This operating mode will allow f or control with an external DMX controller. You must set the starting address f or this mode. If this is your first time using DMX, then it is recommended that you ref er to the “DMX Primer” secti...
Page 10 - Standalone; Automatic
4. Operating Instructions 10 1/12/2011 11:51 AM Master/Slave Mode (Sound-Active) This mode allows a single unit, the master, to operate in either automatic or sound-active mode. W hen additional (slave) fixtures are daisy chained to the master, they will all synchronize with the master and run the s...
Page 11 - PPENDIX; General Troubleshooting
5. Appendix 11 1/12/2011 11:51 AM 5. A PPENDIX General Troubleshooting S YMPT OM P OSSIBLE C AUSE ( S ) P OSSIBLE A CTION ( S ) Breaker/Fuse keeps blowing • Excessive circuit load • Check total load placed on the electrical circuit • Short circuit along the power wires • Check f or a short in the el...
Page 12 - DMX Primer; Data Cabling; DMX Data Cable
5. Appendix 12 1/12/2011 11:51 AM DMX Primer There are 512 channels in a DMX connection. A fixture capable of receiving DMX will require one or a number of sequential channels. The user must assign a starting address on the fixture that indicates the first channel reserved in the controller. There a...
Page 13 - Cable Connectors; Setting the Starting Address
5. Appendix 13 1/12/2011 11:51 AM Cable Connectors Cabling must have a male XLR connector on one end and a f emale XLR connector on the other end. Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a ground loop, and your fixture may perform erra...
Page 14 - Setting up a DMX Daisy Chain
5. Appendix 14 1/12/2011 11:51 AM 3-Pin to 5-Pin Conversion Chart If you use a controller with a 5-pin DMX output connector, you will need to use a 5-pin to 3-pin adapter. The chart below details a proper cable conversion: 3-P IN T O 5-P IN C ONVERSION C HART Conductor 3-Pin Female (Output) 5-Pin Ma...
Page 15 - General Maintenance; Returns Procedure; Claims
5. Appendix 15 1/12/2011 11:51 AM General Maintenance To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage and environment are contributing f actors in determining cleaning frequency. As a general rule, fixtures should be cleaned at least twice a month. Dus...
Page 17 - ONTACT
C ONTACT U S WORLD HEADQUARTERS General Information ................................................................................................. CHAUVET® Address .............................................................................................. 5200 NW 108 th Ave Sunrise, FL 33351 V...
