Page 2 - TAbLE Of cONTENTS
2 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER TAbLE Of cONTENTS TAbLE Of cONTENTS introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3...
Page 3 - iNTRODUcTiON; CPE TEChNICaL SUPPORT TEam; SAfETY DEfiNiTiONS; DANGER
3 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER iNTRODUcTiON iNTRODUcTiON Congratulations on your purchase of a Champion Power Equipment (CPE) product. CPE designs, builds, and supports all of our products to strict specifications and guidelines. With proper product knowledge, safe use, and regular maint...
Page 4 - iMPORTANT SAfETY iNSTRUcTiONS
4 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER iMPORTANT SAfETY iNSTRUcTiONS iMPORTANT SAfETY iNSTRUcTiONS DANGER Engine exhaust contains carbon monoxide, a colorless, odorless, poison gas. Breathing carbon monoxide will cause nausea, dizziness, fainting or death. If you start to feel dizzy or weak, g...
Page 5 - DO NOT use the engine if:; fuel Safety; Gasoline and gasoline vapors:
5 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER iMPORTANT SAfETY iNSTRUcTiONS WARNiNG Operator Work Zone Area Keep work zone clear of debris while working to ensure safe footing. WARNiNG Protective Safety Gear and Clothing Always wear close fitting clothing and ANSI Z87.1 approved eye protection worn...
Page 6 - Training
6 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER iMPORTANT SAfETY iNSTRUcTiONS WARNiNG When adding or removing gasoline: Do not light or smoke cigarettes. Always stop the engine and allow to cool for a minimum of two minutes before refueling. Always loosen gasoline cap slowly to release vapor pressure a...
Page 7 - Preparation
7 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER iMPORTANT SAfETY iNSTRUcTiONS WARNiNG Although the chipper shredder contains a spark arrester, maintain a minimum distance of 5 ft. (1.5 m) from dry vegetation to prevent fires. – Chipper-shredders should be used only for chipping branches 3 in. (7.6 cm) ...
Page 8 - Maintenance, Transport and Storage
8 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER iMPORTANT SAfETY iNSTRUcTiONS – Only attempt to unclog with a small diameter stick that can get chipped. – If a major clog occurs; turn the fuel valve off and let the unit run until dry, turn off the engine, let the unit cool down, unplug the spark plug wir...
Page 9 - Safety and Dataplate Labels; LaBEL
9 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER iMPORTANT SAfETY iNSTRUcTiONS Top Back Side Safety and Dataplate Labels These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact Technical Support Team for possible ...
Page 10 - Danger icon - discharge; Shredder hopper inside; Combustion; Safety icons
10 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER iMPORTANT SAfETY iNSTRUcTiONS LaBEL DESCRIPTION E DANGER PELIGRO DANGER 485 K --- --- --- Colors LPN 2067-L-SF Rev A Size 73 x 33 mm Artwork Notes 3mm corner radius; 2mm safe margin; to be printed on white substrate. Revision Changes --- This artwork belon...
Page 11 - Safety Symbols; SYmBOL; manual before using this product.; Eye and Ear Protection
11 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER iMPORTANT SAfETY iNSTRUcTiONS Safety Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product. SYmBOL mEaNING Read...
Page 12 - openings while machine is running.; Risk of asphyxiation.; Before inspecting, cleaning or servicing the
12 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER iMPORTANT SAfETY iNSTRUcTiONS SYmBOL mEaNING amputation hazard. Contact with rotating blades will cause serious injury. Keep hands out of openings while machine is running. Toxic Fumes. The engine exhaust from this product contains chemicals known to the s...
Page 13 - Operation Symbols; Quickstart Label Symbols
13 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER iMPORTANT SAfETY iNSTRUcTiONS Operation Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product. SYmBOL mEaNING G...
Page 14 - cONTROLS AND fEATURES; used to help stabilize
14 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER cONTROLS AND fEATURES cONTROLS AND fEATURES Read this operator’s manual before operating your chipper-shredder. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference. chipper-shredder 1. han...
Page 15 - Engine
15 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER cONTROLS AND fEATURES Engine 1. muffler 2. air Filter – Protects the engine by filtering dust and debris from the intake air. 3. Choke – Used to start the engine. 4. Fuel Valve – Used to turn fuel supply on and off to engine. 5. Recoil Starter – Used to ma...
Page 16 - Parts included; Part
16 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER cONTROLS AND fEATURES Parts included Part Part Qty. hardware Needed hardware Qty. Tool Needed Chipper Chute 1 Lock Nut M10, Flange 3 1× 15 mm wrench or socket Hopper Support Bracket 1 Flange Bolt M8 × 20 2 1× 12 mm wrench or socket Lock Nut M8, Flange 2 1×...
Page 17 - ASSEMbLY; Unpacking
17 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER ASSEMbLY ASSEMbLY Your chipper-shredder requires some assembly. This unit ships from our factory without oil. It must be properly serviced with fuel and oil before operation. If you have any questions regarding the assembly of your chipper-shredder, call o...
Page 18 - Thread the M6 lock nut onto the threaded stud to secure the; collection bag; Add Engine Oil; WARNiNG; The recommended oil type for typical use is; automotive oil; . However, using the listed conventional oils
18 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER ASSEMbLY 3. Thread the M6 lock nut onto the threaded stud to secure the chute deflector to the discharge chute. 4. From both sides, insert a knob bolt through the slotted hole on the chute deflector and into the threaded hole on the discharge chute. Select...
Page 19 - MAX; NOTicE; Maintenance; cAUTiON; Add fuel; y b c
19 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER ASSEMbLY 4. Check engine oil level before every use and add as needed. MAX OIL DIP STICK NOTicE Once oil has been added, a visual check should show oil about 1-2 threads from running out of the fill hole. If using the dipstick to check oil level, DO NOT ...
Page 20 - DO NOT light cigarettes or smoke when filling the tank.; OPERATiON; chipper-Shredder Location; Work Area
20 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER OPERATiON cAUTiON Use regular unleaded gasoline with a minimum octane rating of 87 and an ethanol content of less than 10% by volume. DO NOT light cigarettes or smoke when filling the tank. DO NOT mix oil and gasoline. DO NOT overfill the fuel tank. Alwa...
Page 21 - Starting the Engine
21 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER OPERATiON SU RRO UNDING AREA Up to 75 ft. (22.9 m) Up to 75 ft. (22.9 m) Up to 75 ft. SAFE ZONE Up to 75 ft. (22.9 m) Up to 75 ft. (22.9 m) Up to 75 ft. Up to 75 ft. WARNiNG Do not lean over or reach across the shredder chute when engine is running. Neve...
Page 22 - chipper-Shredder Operation
22 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER OPERATiON 5. Pull the starter cord slowly until resistance is felt and then pull rapidly. 6. As engine warms up, move the choke lever to “RUN.” NOTicE Keep choke lever in “CHOKE” position for only 1 pull of the recoil starter. After first pull, move chok...
Page 23 - chipping and Shredding Tips; Chipping; Shredding; clearing the Shredder hopper
23 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER OPERATiON WARNiNG ALWAYS use the chipper-shredder for its intended uses only. The chipper-shredder should only be used to chip branches 3 in. (7.6 cm) or less in diameter, or to shred leaves and brush. DO NOT chip anything that is larger than 3 in. (7.6 ...
Page 24 - Stopping the Engine; Under Normal Operation; Storage; Operation at high Altitude
24 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER OPERATiON 4. Using your hands, remove the material that is still atop the shredding chute. DO NOT stick your hands in the shredder hopper, only remove the material on top. 5. Using a branch, or other piece of wood less than 1/2 in. (1.3 cm) in diameter try...
Page 25 - MAiNTENANcE; changing the Engine Oil
25 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER MAiNTENANcE Carb. Code high alt. Jet Part Number min. altitude 16100- Z590511- 01M0 16161-Z153510-00A0 3000-6000 ft. (914.4-1828.8 m) 16161-Z153310-00A0 6000-8000 ft. (1828.8-2438.4 m) WARNiNG Operation using the alternative main jet at elevations lower ...
Page 26 - SPARK PLUG GAP; Specifications; clean the Air filter; inspect chipping blades; Maintenance Schedule; Repair; Shredder Blade and Flail Blade Inspection and Replacement
26 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER MAiNTENANcE SPARK PLUG GAP 5. Refer to the spark plug types in Specifications when replacing the plug. 6. Firmly re-install the plug. 7. Attach the spark plug cable to the spark plug. clean the Air filter 1. Remove the plastic outer casing. 2. Remove the f...
Page 27 - Chipping Blade Sharpening and Replacement; CHIPPER KNIFE CUTTING EDGE
27 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER MAiNTENANcE NOTicE The hammer and blade assembly is precision balanced to ensure smooth operation. Any modification to this assembly could result in damage to the unit and will void the warranty. To Access the Shredder Blades and Flail Blades: 1. Turn th...
Page 29 - STORAGE; chipper-shredder Storage; Engine Stored for Less than 30 Days; Engines Stored for Over 30 Days
29 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER STORAGE EVERY 250 hOURS Clean combustion chamber * To be performed by knowledgeable, experienced owners or CPE certified service centers. STORAGE Refer to the Maintenance sections for proper cleaning instructions. Always disconnect the spark plug wire in...
Page 30 - SPEcificATiONS; Overall Dimensions
30 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER SPEcificATiONS SPEcificATiONS chipper-shredder Specifications Max Diameter Chipper Material . . . . . . . . . . . . . . . . . . . . . . 3 in. (7.6 cm) Max Diameter Shredder Material . . . . . . . . . . . . . . . . . . 1/2 in. (1.3 cm) Overall Dimensions Ne...
Page 31 - TROUbLEShOOTiNG; Problem
31 201353 - 3 iN. (7.6 cM) chiPPER ShREDDER TROUbLEShOOTiNG TROUbLEShOOTiNG Problem Cause Solution Engine will not start. No fuel. Add fuel. Faulty spark plug. Replace spark plug. Unit loaded during start up. Remove load from unit. Engine will not start; Engine starts but runs roughly. Low oil level...
Page 32 - This warranty does not cover the following repairs and equipment:; Normal Wear; Other Exclusions; This warranty excludes:; Contact Information; Address
WARRANTY* CHAMPION POWER EQUIPMENT2 YEAR LIMITED WARR ANT Y Warranty Qualifications To register your product for warranty and FREE lifetime call center technical support please visit: https://www.championpowerequipment.com/register To complete registration you will need to include a copy of the purc...
Page 34 - EMISSION CONTROL SYSTEM WARRANTY; GENERAL EMISSIONS WARRANTY COVERAGE; owner at a CPE Authorized Service Outlet.
EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage . 1. APPLICABILITY: This warranty shall apply to 1997 and later model year small off-road engines (SORE). The ECS Warranty Period shall begin on the date the new en...
Page 35 - applicable to the engine); Systems covered by this; TO OBTAIN WARRANTY SERVICE:
EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of the list applicable to the engine) Systems covered by this warranty Parts Description Fuel Metering System Fuel regulator, Carburetor and internal parts Air Induction System Air cleaner, Intake manifold Ignition System Spark plug...
