Canon VB-S900F- Manual

5 User Manuals This camera comes with an “Installation Guide” and “Operation Guide” (this manual) included in the Setup CD-ROM. In the Setup CD-ROM, the recording software RM-Lite (see “Chapter 1 Before Use” > “RM-Lite”) is also included. The following user manuals are available. How to use this ...

6 The following items must be observed when using the camera. If they are not observed, injury, death and/or property damage may occur. Read the following information carefully and observe the instructions without fail. Important Warnings Safety Precautions Caution TO REDUCE THE RI S K OF ELECTRIC S...

S afety Precautions 7 Precautions for Use Precautions for Use of Built-In Camera Functions and Included Software Notes on Cleaning Warning • If you discover defective conditions such as smoke, strange sounds, heat or strange odors, immediately stop using the camera and contact your nearest dealer. C...

8 Maintenance Turn off the power before cleaning the camera. „ Cleaning of Exterior 1 Dampen a soft cloth with water or diluted neutral detergent and wipe away the grime gently. 2 Wipe with a dry cloth. „ Cleaning of Lens Use a commercial lens cleaner to remove grime on the lens surface. • Auto focu...

9 Table of Contents Introduction .................................................................................................................. 2 Disclaimer ............................................................................................................................... 2 Notes on ...

10 Chapter 2 Initial Settings Preparing the Camera for Use ................................................................................... 24 Installing the Necessary S oftware ............................................................................. 26 Notes on Use with Internet Explorer 9 ...

11 Table of Contents Chapter 5 Admin Tools Admin Tools Overview ............................................................................................... 76 Admin Tools ......................................................................................................................... 76 ...

12 Control for Admin .................................................................................................... 117 Using Control for Admin ...................................................................................................... 117 Chapter 6 Admin Viewer/VB Viewer Overview o...

Chapter 1 Before Use ❏ Camera Features ❏ S oftware Information ❏ Operating Environment and Precautions

14 This camera integrates both camera and server functions into a compact network camera. * In this manual, the memory card that can be used with the camera is referred to as “memory card”. Features Compact and Lightweight Small and light while maintaining full HD video quality, and easy to install....

15 1 Before U s e Installed Software „ Admin Viewer/VB Viewer (See Chapter 6 “Admin Viewer/VB Viewer”) There are two types of Viewer: the VB Viewer, which can be used by Guest Users, and the Admin Viewer for Administrators. The VB Viewer allows users to configure basic camera controls and display vi...

Camera S oftware 17 1 Before U s e RM-Lite (See the “Administrator Manual”) The installer (RMLiteInstall.exe) can be found in the Applications folder on the Setup CD-ROM. RM-Lite Software Configuration Note For details on the usage and functions of RM-Lite, see the “Administrator Manual”. Type Overv...

18 For the latest information on this product (firmware and included software, user manuals, operating environment, etc.), please refer to the Canon Web Site. VB Initial Setting Tool, Admin Viewer/VB Viewer, Admin Tools *1 Set the Control Panel’s font size (DPI) for Admin Tools and Admin Viewer to 1...

19 1 Before U s e Notes on Use When the [Windows Firewall] Function is Enabled When the VB Initial Setting Tool is started, the [Windows Security Alert] dialog box may appear. If the [Windows Security Alert] dialog box appears, click [Unblock]. Once this button is clicked, the warning dialog box wil...

Notes on Operating Environment 21 1 Before U s e „ Enabling the Sound Function to Use Audio In Windows Server 2008/Windows Server 2012, the sound function is disabled by default. To receive audio with the Viewer, follow the steps below to enable the sound function. Note If [Control Panel] is in the ...

Chapter 2 Initial Settings ❏ Preparing the Camera for Use ❏ Initial S etting Tool Installation ❏ Initial S ettings

Preparing the Camera for Use 25 2 In it ial S et tings Operating If an error message appears or the camera fails to operate correctly, see the error message and log message information in “Chapter 7 Appendix”. “Chapter 7 Appendix” Important Before starting operations, make sure that the setting page...

26 Install the following software to perform initial settings for the camera. • VB Initial Setting Tool: Software required for performing initial camera settings • Admin Tools Certificate: An electronic certificate that is required for using Admin Viewer and Admin Tools • .NET Framework 3.5 SP1/.NET...

28 Use the VB Initial Setting Tool to configure the camera network. To launch the VB Initial Setting Tool, double-click the [VB Initial Setting Tool] icon on the desktop. The VB Initial Setting Tool will automatically detect the camera connected to the network and display the camera's MAC address, I...

29 2 In it ial S et tings Once initial settings are complete, check the video on the camera with the VB Viewer. When doing so, set the computer network settings to comply with the IP address and subnet mask settings on the camera. The viewer launches and displays the camera video. If the top page of...

Chapter 3 Top Page of the Camera ❏ Accessing the S etting Page, Admin Tools and Viewer

32 Accessing the Top Page of the Camera From the top page of the camera, you can navigate to the Setting Menu to configure various camera settings, launch Admin Tools, and display the viewer to view video. The top page of the camera appears. (1) Language Button Click to switch the display language. ...

Chapter 4 Setting Page ❏ Administrator Password and Network Detailed S ettings ❏ Camera Date and Time S ettings ❏ Camera Name and Initial Camera S ettings Related S ettings ❏ Video S ize and Quality S ettings ❏ Upload and E-mail Notification S ettings ❏ Video S erver, Audio S erver and HTTP S erver ...

34 From the Setting Menu, you can navigate to each setting page to set various items regarding the camera. Information describing what can be set from each setting page is listed as follows. See each setting page for details. • Network Administrator password, LAN, IPv4, IPv6, DNS and SNMP Settings (...

35 S et ting P age 4 The various settings of the camera are configured by accessing the camera in the web browser. First, access the top page of the camera (p. 32). For details on entering the user name and password, see p. 32. Setting Menu (1) [Admin Viewer] Clicking this button opens Admin Viewer....

36 „ Returning to the Setting Menu Click [Settings menu] at the top right of each setting page to return to the Setting Menu. Note Click on [ Help ] at the beginning of any item to display a detailed explanation of that setting item. Important • Do not open multiple setting pages at one time and try...

37 S et ting P age 4 Administrator Password (1) [Password] Set the administrator password. Up to eight (single- byte) ASCII characters (space or printable characters) can be used. The factory default setting is “camera”. If the Admin Viewer, Admin Tools, etc., are connected, terminate the connection...

38 (5) [AutoIP] Set AutoIP to [Disable] or [Enable]. (6) [IPv4 Address (AutoIP)] When [Enable] is selected in (5), an automatically set IP address is displayed. IPv6 (1) [IPv6] Set IPv6 use to [Disable] or [Enable]. (2) [Auto (RA)] Select [Enable] to set an address automatically using RA (Router Adv...

[Network] S etting Administrator Password, LAN, IP Address, DN S , etc 39 4 S et ting P age (3) [Name S erver Address (DHCP)] Select [Use DHCP] or [Use DHCP/DHCPv6] in [Auto- Setting of Name Server Address] to display the name server address acquired from the DHCP server. (4) [Name S erver Address (...

42 Camera Name [Camera Name] Be sure to enter [Camera Name (alphanumeric characters)]. Up to 15 ASCII characters (spaces and printable characters) may be used for [Camera Name (alphanumeric characters)]. Note • The camera name set here will be shown when the camera is registered for use with include...

44 Note • Focusing may be difficult for the following types of subjects when [Focus] is set to [Auto] or [One-shot AF]. Subjects Difficult to Focus On • After rebooting the camera, it is recommended that you check whether the camera is focusing correctly. • The focus ranges (approximate) are shown i...

[Camera] S etting Initial Camera S ettings and External Device Name 45 4 S et ting P age Select [30] or [60] if brightness changes frequently, such as when a light source passes in front of the camera. Select [5] or [10] if change in brightness is minimal. Installation Conditions (1) [LED S etting] ...

49 S et ting P age 4 RTP Server (1) [RTP] Set RTP to [Disable] or [Enable]. (2) [RTSP Authentication Method] Set the RTSP authentication method to [Basic Authentication], [Digest Authentication], or [No Authentication]. (3) [RT S P Port] Set the RTSP port number to 554 or in the range of 1024 to 655...

51 S et ting P age 4 General Upload (1) [Upload] Select [Upload Disabled], [HTTP Upload] or [FTP Upload] for the upload method. (2) [Video Format] Select the [JPEG] or [H.264(1)] format for video you want to upload. If [H.264(1)] is selected, video is uploaded with the settings defined under [Video]...

[ S erver] S etting the Video S erver, Audio S erver and HTTP S erver 55 4 S et ting P age HTTP Server (1) [Authentication Method] Set the authentication method used with the HTTP server to [Basic Authentication] or [Digest Authentication]. (2) [HTTP Port] Set the HTTP port number to 80 or in the ra...

56 Video Record Setting (1) [Video Record Action] Select the destination of a video recorded when an event occurs. To record to a server selected on the [Upload] in the setting page, select [Upload] and to record to a memory card inserted in the camera, select [Record to Memory Card]. Note The size ...

[Event] S etting Video Record, Volume Detection, External Device Output/Input and Timer 57 4 S et ting P age necessary to set the presets with the Preset Setting Tool under Admin Tools (p. 90). If there is no need for additional camera operation, select [None]. (9) [Video Record] Specify the video r...

58 (4) [Inactive Event Operation] Select the operation to be performed upon an inactive event. If [Enable] is selected, (6) [Preset], (7) [Video Record] and (8) [E-mail Notification] will be executed according to their settings upon an inactive event. (5) [Ongoing Active Event Operation] Select the ...

60 Authorized User Account (1) [User Name], [Password] Enter the user name and password and then click [Add]. The authorized user will be added to the user list. The user name can consist of up to 15 (single-byte) characters using A to Z, a to z, 0 to 9, “-” (hyphen) and “_” (underscore). The passwo...

[Access Control] S etting User Access Privileges 61 4 S et ting P age IPv6 Host Access Restrictions (1) [Apply Host Access Restrictions] Set IPv6 host access restrictions to [Disable] or [Enable]. (2) [Default Policy] If IPv6 host access restrictions are applied, select [Authorize Access] or [Prohib...

65 S et ting P age 4 Certificates (1) [Create S elf- S igned Certificate] After entering each of the following settings, click [Exec] to create a self-signed certificate. Follow the instructions in the message and reboot. The certificate created will take effect after rebooting. Note Creating a cert...

66 (6) [Display S erver Certificate Details] Click [Exec] to view the details of the certificate. (7) [Display S elf CA Certificate] Used for the purpose of testing SSL communications, but otherwise not normally used. (8) [Backup] Click [Exec] to perform a backup of the certificates and private key....

67 S et ting P age 4 802.1X Authentication (1) [802.1X Authentication] Set 802.1X authentication to [Disable] or [Enable]. Initially, if [802.1X Authentication] in [802.1X] is set to [Enable] and [Apply] clicked, [Before changing the setting, set 802.1X authentication to “Disable”. ] will be display...

69 S et ting P age 4 Memory Card Operations (unmount status) (1) [Mount/Unmount] In unmount status, [Mount] will appear. Click [Mount] to mount the memory card. Note microSD, microSDHC, and microSDXC memory cards can be used with the camera. When a memory card is inserted in the card slot, it is mou...

70 Memory Card Operations (mount status) (1) [Mount/Unmount] In mount status, [Unmount] will appear. Click [Unmount] to unmount the memory card. (2) [Operation S ettings], [Video Format], [Pre-event Buffer], [Post-event Buffer], [Overwrite videos] These settings are the same as in “Memory Card Opera...

72 (1) [LAN] LAN interface, maximum packet size settings (p. 37) (2) [IPv4] IP address, IPv4 settings, etc. (p. 37) (3) [IPv6] Settings regarding IPv6 (p. 38) (4) [HTTP S erver] Authentication method, HTTP, and HTTPS port settings (p. 55) [Reboot Item] Setting Items Requiring Rebooting The following...

73 S et ting P age 4 Device Information [Model Name], [Firmware Version], [ S erial Number], [Build Number], [MAC address] Displays information about the currently connected camera. Tool (1) [View Logs] Display a history of camera operations and connections to each viewer, etc. (2) [View Current S e...

74 (1) Video Display Area Displays video currently captured by the camera. (2) [Resize] button Each time this button is clicked, the screen size of the video display area switches between “480 x 270” and “960 x 540”. (3) [Reconnect] button The camera is reconnected. (4) [Zoom] slider, [Zoom] buttons...

Chapter 5 Admin Tools ❏ Privacy Mask S etting ❏ Panorama Image Registration ❏ View Restriction S etting ❏ Camera Preset S etting ❏ Intelligent Function S etting ❏ Viewing Logs ❏ Managing Memory Card Video

76 Admin Tools consists of applications for remotely making camera settings, checking operating conditions, and acquiring logs. Admin Tools This is the top page of Admin Tools. All tools can be launched from this page. Privacy Mask Setting Tool A tool that lets you hide areas you do not want to be s...

Admin Tools Overview 77 5 Adm in Tools Preset Setting Tool A tool that lets you set presets and the home position visually. You can make the desired settings with the mouse by referring to the preview in panorama or full video mode. Intelligent Function Setting Tool This tool is used to set intellig...

78 Launching the Admin Tools The Admin Tools can be launched from the top page of the camera. A user authentication window appears. The Admin Tools top page will appear. (1) [Admin Viewer] Click to launch Admin Viewer. (2) [ S etting Page] Click to launch Setting Menu. (3) [Back to top] Click this b...

79 Adm in Tools 5 A tool that lets you cover certain areas on the camera video with privacy masks. When the camera is panned, tilted, or zoomed, the privacy mask area responds to the camera video. Display Screen of Privacy Mask Setting Tool (1) Video Display Area The video currently captured by the ...

80 such as in the Admin Viewer, the control privileges will be obtained the moment the Privacy Mask Setting Tool is launched. (6) [Control for Admin] button Displays the Control for Admin Panel (p. 117). (7) Registered Privacy Mask Display Area (Capture area) You can check the settings for the area ...

82 Changing/Deleting a Privacy Mask Area How to Change Click the privacy mask area you want to change in the registered privacy mask display area (capture area) or select a privacy mask area by clicking [Next]. Privacy mask areas can be changed using the mouse or by entering values. Entering values ...

84 Display Screens of Panorama Creation Tool (1) [Load from camera] Show the panorama image saved in the camera. (2) [ S ave to camera] Save the currently shown panorama image in the camera. (3) [Load from file] Show JPEG files as a panorama image. (4) [ S ave to file] Save the currently shown panor...

Panorama Creation Tool 85 5 Adm in Tools Note • While a panorama image is being created, the connection of anyone other than Administrators and connections other than RTP are cut off. • When a small value is entered for [Maximum Frame Rate: Video Transmission] under [Video] > [JPEG] in the Settin...

86 View Restriction Setting Tool is a tool that limits the range that can be captured by the camera. If view restrictions have been set, you can limit the displayable capture range using the viewer. [Apply View Restriction S etting] Restrictions set by the View Restriction Setting Tool are applied i...

View Restriction S etting Tool 87 5 Adm in Tools Display Screens of View Restriction Setting Tool (1) Video Display Area The video currently captured by the camera is shown. Pan, tilt, and zoom operations are the same as in the Admin Viewer. For details, see “How to Operate the Viewer” (p. 124). (2)...

88 (10)[Display in panorama screen] Apply the current view restriction settings to the panorama screen. At this point, the settings are not yet saved in the camera. Be sure to click [Save settings]. (11)[Restore settings] Clear the settings you have specified on the screen of the tool and restore th...

Preset S etting Tool 91 5 Adm in Tools Display Screens of Preset Setting Tool (1) Video Display Area The video currently captured by the camera is shown. Pan, tilt, and zoom operations are the same as in the Admin Viewer. For details, see “How to Operate the Viewer” (p. 124). (2) [ S witch Mouse Ope...

92 • [White Balance] Set the white balance of the camera to [Auto] or according to the light source of the condition in which it is used. For details on light sources, see p. 43. • [R Gain], [B Gain] If white balance is set to [Manual], set the respective gains to a value between 0 and 1023. (11)[Ge...

Preset S etting Tool 93 5 Adm in Tools If you click on the panorama screen, the preview frame will move to center on the clicked point. The settings are reflected in the video display area. If you previewed incorrect settings, etc., and want to restore the settings registered in the camera, click [R...

94 Note Digital PTZ is a function for transmitting only the specified part of a camera video. Therefore, this function reduces the load on the network. „ Specifying Detailed Settings If you want to fine-tune the camera angle or to adjust the video, etc., click [Detailed Settings] and specify the det...

Preset S etting Tool 95 5 Adm in Tools Preset Tour Set a preset tour whereby the camera tours and monitors the multiple presets currently set. „ [Preset Tour] Tab Display Screen (1) [Preset Tour] selection box. Select when you want to perform a preset tour from the following options. [Not used] Pres...

97 Adm in Tools 5 This tool is used to set intelligent functions that perform uploads, notify the viewer, etc., if a change has occurred in the captured video due to movement of a subject. The intelligent functions can perform the following 6 types of detection. Use detection types that best serve y...

98 Abandoned Object Detection Detect objects that are carried in and abandoned for a certain amount of time. This function can be used to detect objects that have been left. Abandoned object detection is triggered when an object is left in the detection area for a specified duration. Object abandone...

Intelligent Function S etting Tool 99 5 Adm in Tools Caution Notes on Use of This Camera The intelligent functions are not suitable for applications where high reliability is required. If constant and maximum reliability is required for surveillance it is not recommended that you use this function. ...

100 Display Screen of Intelligent Function Setting Tool (1) Video Display Area The video currently captured by the camera is shown. Detection areas are shown in translucently colored frames (rectangular or polygonal) and the detection line is shown as a translucently colored polygonal line or line s...

Intelligent Function S etting Tool 101 5 Adm in Tools If camera control privileges are not obtained, this function is grayed out. (10)[Detection S ettings] Show the [Detection Settings] dialog box (p. 108). This dialog box allows you to reduce the effects of lighting changes. (11)[Lock camera positi...

102 „ Intelligent Function Settings When you click [Add] in the [Detection Setting List], the [New Detection Settings] dialog box is displayed. Set the [Detection Setting Number] and [Detection Type] of the detection setting you want to add, and then click [OK]. Up to 15 different detection settings...

Intelligent Function S etting Tool 103 5 Adm in Tools Setting Intelligent Function Detection Settings „ Setting Detection Criteria ([Detection Criteria] tab) Set detection criteria while operating the camera and checking the video in the video display area. (1) [Detection S ettings Name] You can use...

104 „ Setting Event Operations ([Event] tab) Set operations to be performed upon detection of changes in a subject. [Event] tab (1) S pecify the operation timing. (Multiple checkboxes can be selected.) [ON Event Operation] checkbox When selected, the operations set in (2) [E-mail Notification] and [...

Intelligent Function S etting Tool 105 5 Adm in Tools An outline for the detection object is drawn using a polygon with up to 32 points. If there are multiple detection objects, the area is drawn around the largest object. Note • Drag the square marks ( ■ ) at each angle to change the shape of the p...

Intelligent Function S etting Tool 107 5 Adm in Tools Note Detection will not be possible for three seconds after the change ratio is modified when camera tampering detection is selected, or when switching into camera tampering detection from another detection mode. Detect criteria for [Passing Dete...

108 [Copy event settings] Copy the event operations of the detection setting selected. [Paste event settings] Paste the copied event operations to the detection setting selected. „ Reducing effects of lighting change Intelligent functions may not work when the entire screen is exposed to sudden chan...

109 Adm in Tools 5 This tool lets you view the operating condition log of the camera. Display Screens of Log Viewer (1) [Download] Download log files from this camera or memory cards. (2) [Reload] Reload the displayed log file and show the latest logs. (3) [Previous File] If there are multiple log f...

110 (13)[Date & Time] Set the date and time of the log you want to show using the filter function. Select the [Specify start date & time] or [Specify end date & time] checkbox to set the date and time. (14)[Apply filter] Show the filtered logs in the log display area. (15)[ S earch for] ...

Log Viewer 111 5 Adm in Tools „ Saving a Log to a File/Opening a Saved Log How to Save Click [Save to local file] and save using the [Save As] dialog box. How to View Click [Open local file] and select a log file using the [Open] dialog box. „ Copying/Searching Logs How to Copy Click to select the l...

112 This utility manages video recorded on a memory card. It allows you to play back recorded video and download it to a computer, display a video list or perform filtering. Display Screens of Recorded Video Utility (1) [Refresh Video List] Update the video list to the current state. (2) [Refresh Do...

Recorded Video Utility 113 5 Adm in Tools Confirming Recorded Video The video list displays the following information: [Date & Time] Displays the date and time of a video recording. [Format] Displays the format of a recorded video ([JPEG] or [H.264]). [Recording Type] Displays the type of record...

114 Downloading Video Download video recorded on a memory card to a computer. Click [Browse] to specify a folder. The video is downloaded to the specified folder. Note When the download folder is changed, the download status of the files in the download folder prior to the change becomes [Not Downlo...

Recorded Video Utility 115 5 Adm in Tools Note • [Real Time] can be selected only for playback of downloaded videos. • [Not Downloaded] or [Partially Downloaded] videos may not be played back in the order they were recorded. Slider/Playback Control Drag the slider to change playback position. The fo...

116 [ S ave Playback Frame As] Video frames that are being displayed can be saved as a separate file. Clear the [Enable H.264 playback] checkbox to play H.264 video in an external player. [Number of downloaded video files] The number of downloaded files the video consist of is displayed. [Playback w...

117 Adm in Tools 5 This panel is used to adjust video from the camera that is displayed by each Admin Tool. The panel is available to the Privacy Mask Setting Tool, View Restriction Setting Tool, Preset Setting Tool and Intelligent Function Setting Tool. Using Control for Admin Click the [Control fo...

Chapter 6 Admin Viewer/VB Viewer ❏ Differences between the Admin Viewer and the VB Viewer ❏ User Authorities and Camera Control Privileges ❏ Viewer S tartup and Operation ❏ Camera Control and Obtaining Camera Control Privileges ❏ Admin Viewer Operation and S ettings

120 Accessing this viewer via a web browser allows you to display video and operate the camera. Two types of viewer are available, the Admin Viewer and the VB Viewer. Major Differences Between the Admin Viewer and the VB Viewer • The operable ranges differ between the viewers. Admin Viewer: Users ca...

Overview of Viewer 121 A d min Viewer/ V B V iewer 6 [Administrator] This user is given all authorities. The user name is fixed to “root”. The Administrator can launch the Admin Viewer from the [Admin Viewer] link on the top page. [Authorized User] Authorized users can launch the Admin Viewer from t...

123 6 A d min Viewer/ V B V iewer Launching the Viewer See “Chapter 3 Top Page of the Camera” > “User Authentication” (p. 32) for information on the user name and password. The viewer is launched. Shutting Down the Viewer Close the web browser in the viewer to shut down. Connecting from Admin Too...

124 Display Screens of Admin Viewer The following gives an overview of the functions of buttons, boxes and other screen elements displayed in the Admin Viewer. The following screen shows the Admin Viewer with all panels opened. In practice, you only open panels that are necessary, and can put them a...

How to Operate the Viewer 125 A d min Viewer/ V B V iewer 6 (11)[Obtain/Release Camera Control] button This button is used to obtain/release the camera control privileges. (12)Information Field Information messages, warning messages and error messages are shown to the user. (13)[Get a S napshot] but...

126 (5) [Reconnect] button The camera is reconnected. (6) [Audio Reception] button Displays the Receive Audio panel. (7) Control Privilege S tatus Indicator Whether or not the current client has camera control privileges is shown in this area. (8) [Obtain/Release Camera Control] button This button i...

How to Operate the Viewer 127 A d min Viewer/ V B V iewer 6 Controlling the Camera Obtain camera control privileges before carrying out the following operations. These operations can be carried out in both the Admin Viewer and the VB Viewer. Note • Operations carried out by clicking or dragging will...

128 „ Changing the Camera Zoom Ratio Move the knob on the slider up or down to zoom in or out The camera zoom ratio will change according to the knob position on the slider. The knob can also be moved by clicking on an empty part of the slider. Note • In the Admin Viewer, you can also control the zo...

130 PTZ panel to the preset position and display the video inside the frame in the video display area. Click the [Home Position] button to move the preview frame on the Digital PTZ panel to the home position and display the video inside the frame in the video display area. Note Register the preset o...

How to Operate the Viewer 131 A d min Viewer/ V B V iewer 6 • When the viewer is launched, the display screen size opens at [Actual Pixels]. „ Displaying in Full Screen Mode You can show video over the entire display. Clicking this button will switch the viewer to full screen mode. To close the full...

132 Select the [Receive audio] checkbox in the Receive Audio panel that appears and use the slider to set an appropriate volume. Note • To receive audio, set [Server] > [Audio Server] > [Audio Transmission from the Camera] to [Enable] in the setting pages beforehand (p. 54). • The first time t...

133 6 A d min Viewer/ V B V iewer The operations and settings that can be performed only in the Admin Viewer are explained. Magnifying Part of the Video (Viewer PTZ) You can use the Viewer PTZ panel to magnify part of the camera’s video in the video display area. „ Viewer PTZ Viewer PTZ uses the dig...

134 Note After changing the preview frame, the video display area will continue to display the cropped video corresponding to the preview frame even after the Viewer PTZ panel is closed. However, when you reconnect to Admin Viewer, the initial status will be restored. „ Exiting Viewer PTZ Click the ...

Performing Operations and S ettings in the Admin Viewer 135 A d min Viewer/ V B V iewer 6 Note Changing the [Pan/Tilt] speed or [Zoom] speed will not change the speed of the slider, or of the pan, tilt or zoom in panorama. „ Setting the Smart Shade Control The smart shade control function differs fr...

136 (1) Exposure Mode Select from [Auto], [Manual], [Auto (Flickerless)] or [Auto (Shutter-priority AE)]. If [Auto] is selected for [Day/Night] under [Camera] in the Setting page (p. 43), select [Auto ], [Auto (Flickerless)] or [Auto (Shutter-priority AE)]. [Auto] The exposure is controlled automati...

Performing Operations and S ettings in the Admin Viewer 137 A d min Viewer/ V B V iewer 6 Example of setting method: Illuminate a white subject (white paper, etc.) using the light source, making sure the subject fills the entire screen, and then execute [One-shot WB]. [R Gain], [B Gain] When setting...

138 • Click [Register] after completing the above settings to register the custom settings. (1) Custom setting button Select the numbered button with the registered custom settings to load the settings. (2) [Register Custom S ettings] The [Register Custom Settings] panel is displayed. (3) [Register ...

Performing Operations and S ettings in the Admin Viewer 139 A d min Viewer/ V B V iewer 6 „ Adjusting Image Quality (1) [Noise Reduction] Select [Mild], [Standard], or [Strong] for the noise reduction setting. Principally, this setting is more effective in low-light conditions. When set to [Strong],...

140 (3) [Intelligent Function (Volume detection)] The volume detection status is displayed. When sound that meets the criteria selected under [Event] > [Volume Detection] in the Setting Page is detected, the icon turns green (p. 56). Example: Volume Detection status ON Recording to a Memory Card ...

Chapter 7 Appendix ❏ Memory Card Access ❏ Modifiers ❏ Troubleshooting ❏ List of Log Messages ❏ List of Viewer Messages ❏ Restore Default S ettings ❏ List of Factory Default S ettings ❏ S pecifications ❏ Index

142 You can set the camera so that the following data is saved automatically to the camera’s memory card. (“Chapter 4 Setting Page”, “[Memory Card] Memory Card Operations and Settings” (p. 69)). When either the storage capacity of the memory card or the number of files that can be saved is reached, ...

Memory Card Access 143 7 Appen di x „ File Name Format for Data Downloaded with Recorded Video Utility Example: Video, manually recorded on S ept. 10, 2013, starting from 16:06:19 (Camera Time Zone: GMT+09:00). (1) Video recording date (2) File creation time (UTC) (3) Recording start time (UTC) (4) ...

Modifiers 145 7 Appen di x „ Available Modifiers The modifiers that can be used for each setting item are specified below. [HTTP Upload] (p. 52) [ Parameter (query string) ] All modifiers can be used. [FTP Upload] (p. 52) [ Subdirectory Name to Create ] Only the modifiers %y,%m,%d,%w,%H,%h,%n can be...

146 Before contacting the dealer where you purchased the product or Canon's Customer Service Center, check the items specified as follows. If a log message is displayed, check the details of the message and corresponding countermeasure in the log message list. Troubleshooting Problem Countermeasures...

148 Log Messages on the Camera Log messages are classified into the following types. Note If no content is recorded in a log for approximately two hours, “-- MARK --” will be recorded in the message area. „ Application (Camera) Messages W001 Starting and stopping of system [info] W030 Startup and sh...

List of Log Messages 151 7 Appen di x V200 Video input warning [warning] V300 Video input error [err] V320 Internal error in intelligent service [err] V321 Pseudo mode setting error in intelligent service [err] V400 Video input initialization error [crit] V401 Video input command error [crit] V402 V...

152 V420 Could not start intelligent service [crit] V421 Intelligent service error [crit] „ Application (Memory Card) Messages M001 Starting and stopping of memory card control module [info] M203 Not enough space on memory card [warning] M204 Invalid file removed [warning] M301 Memory card control m...

List of Log Messages 153 7 Appen di x H201 Timeout disconnect [warning] „ System Messages S001 System started [info] S002 System settings changed [info] S010 Event service started [info] S011 Event service shut down [info] S012 External device service started [info] S013 External device service shut...

157 Appen di x 7 Messages Displayed in the Information Field Messages displayed in the information field of the viewer are classified into the following three types. „ Information Messages List of Viewer Messages Icon Category Explanation Information Message Help messages on various buttons, pull-do...

158 „ Warning Messages Message Explanation Could not connect to the camera. Connection failed due to an invalid IP address, etc. The camera is busy. The connection limit was exceeded. Failed to get camera control privileges. The request for camera control privileges was denied because the camera was...

159 Appen di x 7 It is recommended that you write down the settings for respective camera functions. If you have forgotten the settings and want to set the camera from the beginning, restore the factory default settings first. *For factory default settings, see p. 161. Restoring the Initial Setting ...

161 Appen di x 7 List of Factory Default Settings Item S etting • User Name (Administrator ID) root • Administrator password camera • Path to setting pages admin • LAN LAN Interface Auto Maximum Packet Size 1500 • IPv4 IPv4 Address Setting Method Manual IPv4 Address 192.168.100.1 Subnet Mask 255.255...

168 Specifications Camera Image Sensor 1/4.85 type CMOS (primary color filter) 1/3 type CMOS (primary color filter) Number of Effective Pixels Approx. 2.1 million pixels Scanning Method Progressive Lens 3.5x optical (4x digital zoom) zoom lens with auto focus Fixed focal length lens (4x digital zoom...

172 Numerics 802.1X Authentication .........................................67 A Abandoned Object Detection ...........................105 Access Control ....................................................60 Admin Tools ........................................................76 Admin Tools Certific...