Page 2 - SPECIFICATIONS; COMPONENTS IDENTIFIED BY SHADING AND MARK
– 2 – KV-2199XDK RM-952 SPECIFICATIONS Note Power requirements 110-240 V AC, 50/60 Hz Power consumption (W) Indicated on the rear of the TV Television system B/G, D/K Color system PAL, PAL 60, SECAM, NTSC4.43, NTSC3.58 (AV IN) Channel coverage B/G VHF: E2 to E12 / UHF: E21 to E69 / CATV: S01 to S03,...
Page 4 - DIAGNOSTIC TEST INDICATORS; SELF DIAGNOSTIC FUNCTION
– 4 – KV-2199XDK RM-952 The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automaticallybegin to flash.The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMERlamp flash indicators...
Page 5 - DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT; Diagnostic Item; STOPPING THE STANDBY/TIMER FLASH; times
– 5 – KV-2199XDK RM-952 2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT Diagnostic Item Flash Count* +B overcurrent/overvoltage 2 times Ver tical deflection stopped White balance failure 5 times * One flash count is not used for self-diagnostic. 3. STOPPING THE STANDBY/TIMER FLASH Turn off the power s...
Page 6 - SELF-DIAGNOSTIC SCREEN DISPLAY; channel; Self-Diagnosis screen display; SELF DIAGNOSTIC; HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY; Channel
– 6 – KV-2199XDK RM-952 4. SELF-DIAGNOSTIC SCREEN DISPLAY For errors with symptoms such as “power sometimes shuts off ” or “screen sometimes goes out” that cannot be confirmed, itis possible to bring up past occurances of failure for confirmation on the screen: [To Bring Up Screen Test]In standby mo...
Page 7 - SELF-DIAGNOSTIC CIRCUIT
– 7 – KV-2199XDK RM-952 6. SELF-DIAGNOSTIC CIRCUIT [+B overcurrent ªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ONand the voltage to pin 18 of IC301 should go down when V.SYNC is more than sevenver ticals in a period, the unit will automatically turn off. ...
Page 8 - WARNING; Getting Started; Step 1; Connect the antenna; Using Your New TV; Connecting a VCR; or; SECTION 1
– 8 – KV-2199XDK RM-952 2 WARNING • Dangerously high voltages are present inside the TV. • Operate the TV only between 110 – 240 V AC. To prevent fire or shock hazard, do not exposethe TV to rain or moisture. Do not operate the TV if any liquid or solid objectfalls into it. Have it checked immediate...
Page 9 - Using Y; CAUTION; Preset the channels automatically; Connecting optional components; Connecting video equipment using the; ONE-PUSH AUTOMATIC PROGRAMING
– 9 – KV-2199XDK RM-952 5 Using Your New TV Using Y our New TV 1 1 VHF LOW B/G ONE-PUSH AUTOMATIC PROGRAMMING ONE-PUSH AUTOMATIC PROGRAMING 1 2 Notes • If you connect a stereo VCR, connect the yellow plug to (the yellow jack) and the white plug to (the black jack). • If you connect a VCR to the ˘ (a...
Page 10 - Presetting channels automatically; Securing the TV
– 10 – KV-2199XDK RM-952 8 Using Your New TV VHF LOW B/G AUTO PROGR TV 1 2 3 4 6 7 8 9 ÷ 0 5 JUMP SOUND MODE FAVORITE PROGR Á ONE-PUSH AUTOMATIC PROGRAMING Presettingchannels You can preset up to 100 TV channels innumerical sequence from programnumber 1 using the remote and thebuttons on your TV as ...
Page 11 - To change the TV system setting; Presetting channels manually; To change the color system setting; Skipping program numbers; To preset the skipped program number again
– 11 – KV-2199XDK RM-952 9 Using Your New TV Using Y our New TV 1 Press SELECT until“MANUAL PROGRAM”appears. 2 Press + or –. 3 Press PROGR +/– or thenumber buttons until thedesired program numberappears. 4 Press + or – until thedesired channel pictureappears. 5 Press SELECT. To change the TV system ...
Page 12 - Changing the on-screen display language; Watching the TV
– 12 – KV-2199XDK RM-952 12 Using Your New TV To Turn off temporarily Turn off completely Mute the sound Watch the video input(VCR, camcorder, etc.) Jump back to the previous channel Display the on-screen information* Adjust the volume of each TVprogram automatically * The picture, sound, and either...
Page 13 - Setting the Wake Up timer; To cancel the Wake Up timer; Setting the Sleep timer; To cancel the Sleep timer; Selecting the picture and sound modes; To select the picture mode; To select the sound mode
– 13 – KV-2199XDK RM-952 13 Using Your New TV Using Y our New TV Setting the Wake Up timer 1 Press until the desired period of timeappears. 2 Select the TV program or video mode you want to display when you wakeup. 3 Press u or set the Sleep timer if you want the TV to turn off automatically. The in...
Page 14 - Adjusting the picture and sound settings; Selecting a favorite channel
– 14 – KV-2199XDK RM-952 15 Advanced Operations PICTURE COLOR BRIGHT HUE* TREBLE BASS SHARP SELECT PICTURE 60 Adjusting the picture and sound settings 1 Press SELECT until thedesired setting appears. Each time you pressSELECT, the setting itemwill change as follows: 2 Press + or – to adjust theitem....
Page 15 - Additional Information; Self-diagnosis function
– 15 – KV-2199XDK RM-952 17 Advanced Operations Blocking thechannels(CHILD LOCK) You can prevent a child from watchingcertain programs by using the buttonson the remote control. 1 Select the TV program you want to lock. 2 Press SELECT until “CHILDLOCK” appears on thescreen. 3 Press + or – to select“...
Page 16 - Troubleshooting
– 16 – KV-2199XDK RM-952 19 Additional Information Snowy picture Noisy sound Distorted picture Noisy sound Good picture Noisy sound No picture No sound Troubleshooting If you find any problem while viewing your TV, please check the following guide. Ifany problem persists, contact your Sony dealer . ...
Page 17 - Identifying parts and controls; Front panel
– 17 – KV-2199XDK RM-952 21 Additional Information • Use the fine tuning (FINE) function. (page 10) • Contact your nearest Sony service center. (page 18) –– — Possible cause Symptom Solutions • There is interference from external sources, e.g.,heavy machineries, nearbybroadcast station. • Your TV ma...
Page 18 - Remote Control
– 18 – KV-2199XDK RM-952 23 Additional Information Remote Control Button function For general TV operations For Teletext operations 1 u (power) button (11) 2 ; (TV) button (12) 3 Number buttons (11) 4 JUMP button (12) 5 PROGR +/– buttons (11) 6 SELECT button (9) 7 PIC MODE button (14) 8 +/– buttons ...
Page 21 - REMOVING PROCEDURES; Do not damage the surface of anode-caps with sharp shaped objects.; HOW TO HANDLE AN ANODE-CAP
– 21 – KV-2199XDK RM-952 2-8. PICTURE TUBE REMOVAL • REMOVAL OF ANODE-CAP NOTE : After removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon paint on theCRT. • REMOVING PROCEDURES 1 Do not damage the surface of anode-caps with sh...
Page 22 - SECTION 3
– 22 – KV-2199XDK RM-952 • The following adjustments should be made when a complete realignment is required or a new picture tube is installed. • These adjustments should be performed with rated power supply voltage unless otherwise noted. Controls and switches should be set as follows unless otherw...
Page 23 - Minimize the brightness setting.; Horizontal and Vertical Static Convergence; and blue dots are on top of each other at the center of the screen.; Center dot; If the red, green and blue dots are not balanced or aligned, then; Purity
– 23 – KV-2199XDK RM-952 3-2. CONVERGENCE Preparation : • Before starting this adjustment, adjust the focus, horizontal size and vertical size. • Minimize the brightness setting. • Provide dot pattern. (1) Horizontal and Vertical Static Convergence (Moving vertically), adjust the V.STAT magnet so th...
Page 24 - R B
– 24 – KV-2199XDK RM-952 4 Y separation axis correction magnet adjustment. 1. Receive the cross-hatch signal and adjust [PICTURE] to [MIN] and [BRIGHTNESS] to [STANDARD] . 2. Adjust the Y separation axis correction magnet on the neck assembly so that the horizontal lines at the top and bottom of the...
Page 25 - F LY BAC K T R A N S F O R M E R ( T 5 0 3 ); WHITE BALANCE ADJUSTMENT; ADJUSTMENTS
– 25 – KV-2199XDK RM-952 (3) Screen-corner Convergence b a c d a-d : screen-corner misconvergence a d c b a to d : Permalloy assembly Fix a Permalloy assycorresponding to themisconverged areas 3-3. FOCUS ADJUSTMENT Adjust FOCUS control on the flyback transformer for the best focus. F LY BAC K T R A ...
Page 26 - VIDEO IN 1
KV-2199XDK RM-952 KV-2199XDK RM-952 KV-2199XDK RM-952 – 36 – – 37 – – 35 – SECTION 5 DIAGRAM 5-1. BLOCK DIAGRAM YC JUNGLE IC301CXA2130S <slave:88H> MONITOROUT TV V in TV L in TV R in TV V in V1 V in 43 12 V1 V in V1 L in V2 V in V2 V in 4 V2 L in L out 2 JACK BLOCK J401 4P J902 2P VIDEO IN 1 V...
Page 27 - NECK ASSY
KV-2199XDK RM-952 – 39 – KV-2199XDK RM-952 KV-2199XDK RM-952 – 38 – – 40 – CN604 CN306 CN703 DY 1 DGC B 9V IK 1 5 6 (RGB OUT) 1 E CN704 PICTURE TUBE 1 2 3 4 5 6 H+ H+ H- H- V- V+ 1 2 3 4 5 6 7 VM GND 9V VM MUTE GND NC +B CN5901 1 2 3 7 VM GND 9V +B (POWER SUPPLY, HV, MICON, Y/C JUNGLE) 1 2 3 DGC NC ...
Page 28 - -4. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS; Readings are taken with a 10 M; N o t e : T h e c o m p o n e n t i d e n t i f i e d b y s h a d i n g a n d
– 41 – KV-2199XDK RM-952 5-4. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS Note: • All capacitors are in µ F unless otherwise noted. • All electrolytic capacitors are rated at 50V unless otherwise noted. • All resistors are in ohms.k Ω = 1000 Ω , M Ω = 1000k Ω • Indication of resistance which does n...
Page 29 - A BOARD WAVEFORMS
– 42 – KV-2199XDK RM-952 4.5Vp-p (V) 3.8Vp-p (V) NTSC 3.58 NTSC 4.43 PAL 0.7Vp-p (H) 1.2Vp-p (H) 1.1Vp-p (H) 920Vp-p 125Vp-p 0.9Vp-p (H) 1.3Vp-p (H) PAL/NTSC 3.58 SECAM/NTSC 4.43 0.8Vp-p (H) SECAM 0.8Vp-p (H) 1.0Vp-p (H) PAL/NTSC 3.58 NTSC 4.43 3.0Vp-p (H) 3.1Vp-p (H) SECAM NTSC 4.43 PAL/SECAM/NTSC ...
Page 30 - board; Schematic diagram
– 44 – – 45 – – 43 – A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 B C D E F G H I J (1) Schematic Diagram of A 1/2 board 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
Page 32 - A BOARD; – A Board –; Schematic diagrams
KV-2199XDK RM-952 KV-2199XDK RM-952 KV-2199XDK RM-952 – 50 – – 51 – – 49 – 5 8 2 6 2 2 3 8 8 8 INT0 INT1 INT2 TEX TX EXTAL XTAL RST MP V DD V SS RMC AN0~AN5 6 PA0~PA7 PORT A PORT B PORT C PORT D PORT E PORT F PORT G PB0~PB7 PC0~PC5 PC6~PC7 PD0~PD7 PE0~PE1 PE2~PE3 PE4~PE6 PF0~PF7 PG3~PG6*, PG7 S1 SO ...
Page 35 - Board –; PRINTED WIRING BOARDS
KV-2199XDK RM-952 KV-2199XDK RM-952 – 56 – – 55 – PAL 25Vp-p (H) 89Vp-p (H) NTSC 3.58 NTSC 4.43 75Vp-p (H) 4 2 2 2 1 2 3 SECAM 93Vp-p (H) PAL/SECAM : NTSC : 86Vp-p (H) 95Vp-p (H) 80Vp-p (H) 90Vp-p (H) – C 3 Board – – VM 1 Board – [VELOCITY MODULATION] VM 1 C 3 [RGB OUT] PRINTED WIRING BOARDS C 3 BOA...
Page 36 - TOP VIEW
KV-2199XDK RM-952 KV-2199XDK RM-952 – 60 – – 59 – 5-5. SEMICONDUCTORS DIODE AK04V0AU-01Z-V1EL1ZGP08DRD33EB3TRGP02-17EL-6433 D4SB60L ERC04-06SERN4ZRS3F331DQ06-FC5 ERA22-08ERD29-08J DTZ10BDTZ-TT11-15BRD10S-BMA111-TXUDZS-TE17-5.1BUDZS-TE17-6.8BUDZS-TE17-9.1B1SS355TE-17 CATHODE ANODE CATHODE ANODE CATHO...
Page 37 - a r e c r i t i c a l
KV-2199XDK RM-952 – 61 – KV-2199XDK RM-952 – 62 – SECTION 6 EXPLODED VIEW NOTE: • Items with no par t number and no des-cription are not stocked because theyare seldom required for routine service. • The construction par ts of an assembledp a r t a r e i n d i c a t e d w i t h a c o l l a t i o nnu...
Page 38 - SECTION 7; μμ
– 63 – REF. NO. PART NO. DESCRIPTION REMARK The components identified by shadingand mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK KV-2199XDK RM-952 * A-1299-049-A A BOARD COMPLETE ******************** 1-900-702-13 LEAD ASSY (1CORE),JUMP...
Page 45 - A C
– 70 – REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK The components identified by shadingand mark ! are critical for safety. Replace only with part number specified. KV-2199XDK RM-952 <SWITCH> S502 1-572-707-11 SWITCH, LEVER S600 ! 1-571-433-21 SWITCH, PUSH (AC POWE...
Page 46 - F VM
– 71 – REF. NO. PART NO. DESCRIPTION REMARK The components identified by shadingand mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK KV-2199XDK RM-952 R712 1-215-922-11 METAL OXIDE 6.8K 5% 3W F R713 1-247-752-11 CARBON 1K 5% 1/2W R714 1-21...
Page 47 - Sony Corporation; TV Business of General Area; English
– 72 – REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK The components identified by shadingand mark ! are critical for safety. Replace only with part number specified. KV-2199XDK RM-952 <COIL> L5901 1-414-187-11 INDUCTOR 47UH L5902 1-414-856-11 INDUCTOR 10UH <TRANS...
