Page 2 - Structure of the Users Guide; Before You Begin
Structure of the Users Guide Before You Begin Operating Procedures Troubleshooting Appendix Read here first. Chapter 1 Chapter 2 Chapter 3 Chapter 4
Page 4 - Important Information
i Important Information • This manual is designed to help you to install, operate and maintain the trimmer. Please read and under- stand this manual, and keep it in a safe and convenient place. • Do not operate the trimmer until you read and understand the instructions in this manual.• Canon shall n...
Page 5 - Safe Use of Machine; Operating Safety Precautions; WARNING
ii Safe Use of Machine To use this machine safely, proper operation and periodic maintenance are indispensable. Read the safety precautions described in this manual thoroughly, and do not perform operations or maintenance procedures until you understand them completely. The operating procedures and ...
Page 6 - FCC NOTICES; NOTICE
iii FCC NOTICES NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-ference when the equipment is operated in a commercial enviro...
Page 7 - CONTENTS
iv CONTENTS Important Information ...............................................................................................................iSafe Use of Machine ............................................................................................................... iiOperating Safety Pre...
Page 9 - Machine Descriptions
1-2 Machine Descriptions Machine Descriptions [1] [2] [3] [1] Two-Knife Trim Section (See page 1-3.)[2] Conveyor Section (See page 1-4.)[3] Trim Ejecting Section (See page 1-5.)
Page 10 - Section Descriptions
Section Descriptions 1-3 Section Descriptions [1] Two-Knife Trim Section Each booklet delivered from the upstream trimmer is trimmed along its top and bottom, and then delivered to the conveyor section. 1 2 Transport Belts These belts move booklets. Top Cover Trim Knives These knives trim top and bo...
Page 14 - Operating Procedures
2-1 2 CHAPTER Operating Procedures Trimmer Setup ..................................................................................................................................... 2-2 Operation While Trimming ...........................................................................................
Page 15 - Trimmer Setup
2-2 Trimmer Setup Trimmer Setup 1 Turn on the power switch on the saddle stitcher first, then turn on the power switch on the host machine (printer). The trimmer will also be powered on as it is connected to the saddle stitcher. See the operation manual for the printer and set up the printer.
Page 16 - Operation While Trimming
Operation While Trimming 2-3 Operation While Trimming When the conveyor is full of booklets, remove the booklets. If the machine stops because the conveyor is full, remove the booklets, and operation restarts automatically. · If you remove booklets before the conveyor is full, you can increase produ...
Page 18 - Troubleshooting
3-1 3 CHAPTER Troubleshooting This section describes some possible problems, and suggests some solutions. Error Messages.................................................................................................................................... 3-2 Service Call Error ...........................
Page 19 - Error Messages; Service Call Error
3-2 Error Messages Error Messages If an error occurs and the machine does not work properly, “SERVICE CALL ERROR” appears on the LCD of the host machine (printer). If “SERVICE CALL ERROR” appears, do the following: Service Call Error If the SERVICE CALL ERROR appears on the LCD of the host machine, ...
Page 20 - Error Message Chart
Error Messages 3-3 Error Message Chart Follow suggested procedures for the error indicated on the host machine (printer). *1 If this error message appears when the conveyor is not full, trim may be blocking the sensor. Cause of Error Remedy The top cover is open. Close the top cover . The conveyor i...
Page 21 - Clearing Paper Jams
3-4 Clearing Paper Jams Clearing Paper Jams Procedure 1 Open the transport unit and check to see if there are any paper chips left on the booklet feed path. (See page 3-3.) Procedure 2 The transport belts must be cleaned. Contact your local authorized dealer. E F2 Jam in Conveyor Section • Paper chi...
Page 22 - Appendix
4-1 4 CHAPTER Appendix Specifications ....................................................................................................................................... 4-2 Index .......................................................................................................................
Page 23 - Specifications
4-2 Specifications Specifications Specifications * 1 If the cover sheet is thinner than the other sheets in the booklet, the cover sheet may be scratched. It is recommended to use a thicker sheet for the cover sheet. * 2 The maximum number of sheets trimmable can change depending on the connected ho...
Page 24 - Index
Index 4-3 Index B Booklet Transport Unit ..................................... 1-3 C Conveyor Full ................................................... 3-3 Conveyor Section ..................................... 1-2, 1-4 D Delivery Chute .................................................. 1-5 Delivery ...
