Page 2 - Confirm that the package contains the following items:; IMPORTANT WARNINGS; CAUTION; INTRODUCTION
1 Thank you for purchasing the Canon Video Visualizer RE-450X.The RE-450X is a user-friendly portable image input device with a built-in video camera and a 12 × zoom lens. It projects images of flat documents, three-dimensional objects, film, etc., onto a video monitor. Here are the main features: •...
Page 3 - IMPORTANT USAGE INSTRUCTIONS; TO REDUCE THE RISK OF ELECTRIC SHOCK,; FCC NOTICE
2 E IMPORTANT USAGE INSTRUCTIONS WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN ORMOISTURE. FCC NOTICE Note: This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are desig...
Page 4 - IMPORTANT SAFETY INSTRUCTIONS
3 IMPORTANT SAFETY INSTRUCTIONS In these safety instructions the word “product” refers to the Canon Video Visualizer RE-450X andall its accessories. 1. Read Instructions—All the safety and operating instructions should be read before the product isoperated. 2. R e t a i n I n s t r u c t i o n s — T...
Page 6 - CONTENTS
5 CONTENTS IMPORTANT SAFETY INSTRUCTIONS ……… 3 1. NOMENCLATURE AND FUNCTIONS ………… 6 2. ASSEMBLING, STORING AND CONNECTION … 8 3. OPERATION ……………………………………… 11 Manual Focusing ………………………………………… 12 Film Projection …………………………………………… 12 Readjusting the White Balance ………………………… 13 Changing the angle to Let...
Page 7 - NOMENCLATURE AND FUNCTIONS; Rear Panel
RE-350 VIDEO V ISUALIZER 6 E Power switch (see page 11) Arm Arm lock releaselever Rear panel Camera head Lens cap Illumination lamp Document table and Backlight Carrying handle Operation panel After turning the power OFF, wait at least 5 seconds before turning the powerON again. Turning the power ON...
Page 8 - Operation Panel
7 LOW HIGH RED BLUE MANUAL AUTO WHITEPAPER POWER LIGHT BACK LIGHT INPUT SELECT WHITE BALANCE EXPOSURE HARD WIDE TELE NEAR FAR MANUAL AUTO SOFT DETAIL FOCUS ZOOM STILL PICTURE ZOOM PRESET Operation Panel LIGHTS button/indicator Use this button to turn ON the illumination lamps for reflectioncopies. T...
Page 9 - Unfold and raise the pair of illumination lamps.; Assembling; ASSEMBLING, STORING AND CONNECTION
8 E Unfold and raise the pair of illumination lamps. Raise the right-hand illumination lamp first ( ), then the left- hand illumination lamp ( ). Press the arm lock release lever, and raise thearm until it stops. Direct the camera head towards the documenttable. Remove the lens cap. Keep the lens ca...
Page 10 - Storing; Put the lens cap to the lens.
9 Storing Put the lens cap to the lens. Direct the camera head sideways until it stops. Hold the arm with your right hand and pressthe arm lock release lever, then pull the armdown to the document table very carefully. Fold the pair of illumination lamps very carefully. Fold the left-hand illuminati...
Page 11 - Connection; RGB cable; NTSC
10 E VIDEO OUT S VIDEO OUT RGB OUT RGB IN AC INLET RS-232C To connect the RE-450X to a liquid-crystal projector, use the RGB cable included in the package. Use thepower cable included in the package. Connection To protect the RE-450X as well as other equipment in use, make sure all theequipment (if ...
Page 12 - Turn ON the power source of the other equipment to be used.; OPERATION
11 POWER Turn the power ON. When the power of the RE-450X is turned ON, the POWERindicator on the operation panel lights up. Turn ON the power source of the other equipment to be used. Either the power of the RE-450X or other equipment may be turned on first. Put the document at the center of the do...
Page 13 - Undesirable objects for focusing; Film Projection; Manual Focusing
12 E When trying to focus correctly or focusing on a particular point of three-dimensional objects, you canachieve focusing by pressing the manual focusing buttons. The manual focusing is valid up to approx.65mm above the document table. HARD WIDE TELE NEAR FAR MANUAL AUTO SOFT DETAIL FOCUS ZOOM STI...
Page 14 - Freezing an output image; Readjusting the White Balance; Changing the angle to Letter/A4 size
13 D WIDE TELE NEAR FAR MANUAL AUTO FOCUS ZOOM STILL PICTURE ZOOM PRESET STILL PICTURE When an output image is a moving picture, if you press the STILLPICTURE button, the output image will be frozen. The STILL PICTURE indicator lights up while the image is frozen. If you press the STILL PICTURE butt...
Page 15 - Adjusting Brightness and Picture Contrast; Projecting white documents
14 E LOW HIGH E WHITEPAPER EXPOSURE HARD NE AUTO SOFT DETAIL FO To adjust brightness, turn the EXPOSURE knob. Turn the knobtoward the HIGH side to brighten the image. Turn the knob towardthe LOW side to darken the image. Use the DETAIL control to adjust picture quality. Turn the controltoward the HA...
Page 16 - Output Equipment; SYSTEM CONNECTION
15 To RGB input terminal To S-video input terminal or video input terminal VIDEO OUT S VIDEO OUT RGB OUT RGB IN AC INLET RS-232C To output to a video monitor, c o n n e c t t h e R E - 4 5 0 X t o amonitor’s video input terminalusing a commercially availablevideo cable. The video monitorprojects ima...
Page 17 - Changing to Pictures via External Input Equipment
16 E LOW HIGH RED BLUE MANUAL AUTO WHITEPAPER POWER LIGHT BACK LIGHT WHITE BALANCE EXPOSURE INPUT SELECT BACK LIGHT INPUT SELECT To switch to pictures from external input equipment, press theINPUT SELECT button. The INPUT SELECT indicator lights up, and pictures are outputfrom the equipment connecte...
Page 18 - Recording by VCR; VCR
17 VIDEO OUT S VIDEO OUT RGB OUT RS-232C If you want to record using a VCR, connect the RE-450X to the VCR using a commercially available videocable. For details of operation, refer to the instruction manual for the equipment to be used. Recording by VCR VCR Video cable To VIDEO INterminal Rear pane...
Page 19 - Functions Controlled by a Computer; Category; System
18 E Functions Controlled by a Computer The following functions can be controlled by a computer. For more information, please contact your dealer. Category Abbreviation Meaning Camera control Zoom lens control Focus control White balance setting Exposure compensation Still picture Outline adjustment...
Page 20 - TROUBLESHOOTING
19 The fluorescent illumination lamps and backlight are consumables.Replace with a new lamp if a lamp starts flickering or becomes dark.For details of replacement, please consult your dealer. If the RE-450X does not function properly, check the following points before contacting your dealer. Problem...
Page 21 - SPECIFICATIONS
20 E Signal output method Image device Effective pixels Synchronization Resolution Imaging speed Projection lens Projection range Zoom Focusing Iris adjustment(exposure) White balance Illumination lamps Backlight Input sources Input/output terminals Power source Power consumption Dimensions Weight O...
