Canon LBP-2460 - Manual
Canon LBP-2460 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – We were able to use the OEM drum; WX Technical Instructions; Make sure you don’t lose the retain-; We have had no problems using the; Notes
- Page 3 – Rotate; Be careful not to damage felts,
- Page 4 – Install the retaining ring.
- Page 5 – Remember which gear goes
- Page 6 – Do not bend the sensor bar.
- Page 7 – The two halves of the toner hopper
- Page 8 – If these foam pads are damaged,
Canon LBP-2460
Data Products DD524
HP 5Si, 5Si MX, 5Si Mopier
IBM Network Printer 24
Lexmark Optra N Model 240
QMS 2425-2425 EX
Troy 524
Part Number: C3909A
Gram Load: 840 grams
Yield @ 5%: 15,000 pgs
Pages/Min.: 24ppm
Resolution: 600 dpi
Needle Nose Pliers
Small Flat Blade Screwdriver
#2 Phillips Head Screwdriver
Small Hammer
Soft Lint-Free Cloth/ Damp Cloth
5/32” Drift Punch
Anhydrous Isopropyl Alcohol
800gms 5Si Toner
Nu-Finish (optional)
Damp Cloth
Technical Instructions
Printers
OEM Info
Tools
1
Step 1
Locate and remove the cartridge clips on
both sides of the cartridge using your fin-
ger. Gently pry up on the clip until it pops
up.
(See Photo 1)
Photo 1
Photo 2a
Photo 2b
WXTECH
Step 2
Using a flat blade screwdriver, pry up on
the other clip and remove it.
(See Photo 2a)
NOTE:
It is very likely that these clips will
break while they are being removed. If
these break, replace with aftermarket
part. You may need to use the springs
from the OEM clip.
(See Photo 2b)
E-mail: [email protected]
Website:
www.futuregraphicsllc.com
US 1 800 394.9900
Int ’l +1 818 837.8100
FAX 1 800 394.9910
Int ’l +1 818 838.7047
D A L L A S , U S A
US 1 877 499.4989
Int ’l +1 972 840.4989
FAX 1 877 774.1750
Int ’l +1 972 840.1750
AT L A N TA , U S A
US 1 877 676.4223
Int ’l +1 770 516.9488
FAX 1 877 337.7976
Int ’l +1 770 516.7794
M I A M I , U S A
US 1 800 595.429
Int ’l +1 305 594.3396
FAX 1 800 522.8640
Int ’l +1 305 594.3309
S A N F O R D, U S A
US 1 800 786.9049
Int ’l +1 919 775.4584
FAX 1 800 786.9049
Int ’l +1 919 775.4584
T O R O N T O, C A N
CAN 1 877 848.0818
Int ’l +1 905 712.9501
FAX 1 877 772.6773
Int ’l +1 905 712.9502
N E W Y O R K , U S A
US 1 800 431.7884
Int ’l +1 631 345.0121
FAX 1 800 431.8812
Int ’l +1 631345.0690
S Y D N E Y, AU S
AUS 1 800 003.100
Int ’l +62 02 9648.2630
FAX 1800 004.302
Int ’l +62 02 9548.2635
B U E N O S A I R E S , A R G
ARG 0810 444.2656
Int ’l +011 4583.5900
FAX +011 4584.3100
M O N T E V I D E O, U R Y
URY 02 902.7206
Int ’l +5982 900.8358
FAX +5982 908.3816
J O H A N N E S B U R G , S . A .
S.A. +27 11 974.6155
FAX +27 11 974.3593
M E L B O U R N E, AU S
AUS 1 800 003. 100
Int ’l +62 03 9561.8102
FAX 1 800 004.302
Int ’l +62 03 9561-7751
CO R P O R AT E
LO S A N G E L E S , U S A
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Photo 3 Step 4 Set the hopper aside. If you have a wastehopper fixture, set the waste hopper in thefixture. If not, place the waste hopper onthe table. (See Photo 4) Photo 5 Photo 6 Step 6 Remove the drum, blow off excess tonerwith compressed air and clean with iso-propyl alcohol. Wrap the drum in a...
Photo 9 Photo 12 Step 12 Apply padding powder to the OPC drumand install. The big helical gear will go onthe right side of the waste hopper. Installthe drum axle only far enough to hold thedrum against the wiper blade. Rotate drum so the wiper blade wipes thepadding powder off the drum. (See Photo12...
Photo 14 Photo 17 Photo 19 Photo 20 4 WX Technical Instructions Step 14 Install the retaining ring. (See Photo 14) Step 15 Set waste hopper aside and cover. Step 16 If you have a toner hopper fixture, placetoner hopper in fixture or place tonerhopper on the workbench. Need trust-worthy, detailed Tec...
