Bryston 6B SST - Manual - manualsarea.com

Page 2 - BSST; THREE CHANNEL POWER AMPLIFIER; Table of Contents

6BSST THREE CHANNEL POWER AMPLIFIER Table of Contents General Introduction Page 1 Instalation and Ventilation Rear Panel Input Settings/Connections Page 2 Setting Input Selector Switch Balance Input Connector Configuration Setting Polarity Setting Input Sensitivity Output Binding Posts and Polarity ...

Page 3 - BSST Three Channel Power Amplifier; The

6BSST THREE CHANNEL POWER AMPLIFIER 1 Introduction Thank you for choosing the 6BSST Three Channel Power Amplifier . Bryston welcomes any suggestions you may have, or comments regarding the operation of your amplifier. We consider you, our customer, to be Bryston’s most important resource, and your o...

Page 4 - Rear Panel Input / Output Connections; ‘XLR’ type; This input connector; Balanced input Vs Single ended input:

6BSST THREE CHANNEL POWER AMPLIFIER 2 Rear Panel Input / Output Connections 1. Input Select Switch. Each 6BSST channel gives the user the option of switching between either balanced input or single ended input. 2. Balanced Input connector. ( Imp. 20k ) This input connector accepts standard ‘XLR’ or ...

Page 5 - Coin

6BSST THREE CHANNEL POWER AMPLIFIER 3 6. Output binding posts & polarity. The RED binding post is connected to the amplifier output . Connect to this post the (+) terminal on the loudspeaker. The BLACK binding post is connected to signal ground . Connect to this post the (-) terminal on the loud...

Page 6 - Front Panel; indicates channel has no power.

6BSST THREE CHANNEL POWER AMPLIFIER 4 Front Panel 1. 'SST POWER' switch The front panel label 'SST POWER', is a touch sensitive membrane switch used to apply or remove a/c line power to the 6BSST circuitry. Push firmly the center of the switch until the power-up sequence begins. Push again and the 6...

Page 7 - Power Control Panel; The circuit breaker; strip; fig W

6BSST THREE CHANNEL POWER AMPLIFIER 5 Power Control Panel 1. Master circuit - breaker. The 6BSST uses a magnetic-trip circuit breaker (1) to protect the amplifier. This switch should be ‘OFF’ when installing the 6BSST. When switched ‘OFF’ all A/C power is removed from the amplifier, including standb...

Page 8 - Rack Mounting Instructions; FUSES - USE SAME TYPE ONLY; TOP VIEW; DO NOT

6BSST THREE CHANNEL POWER AMPLIFIER 6 Rack Mounting Instructions Removing the channels makes rack mounting far easier as the chassis will be much lighter. Before removing any screws from the 6BSST be sure the power cord is removed from the unit. Remove the screws indicated on the top and bottom view...

Page 9 - Typical 5.1 Home Theatre Setup

6BSST THREE CHANNEL POWER AMPLIFIER 7 Typical 5.1 Home Theatre Setup Right Front Left Front Center Powered Subwoofer Right Rear Left Rear Home Theatre processor 4BSST 2 x 300w per ch. 6BSST 3 x 300w per ch

Page 15 - 0 Kohms single ended

6BSST THREE CHANNEL POWER AMPLIFIER 13 Technical Specifications Power Output, 29dB - 1.7Vin = 300W @ 8 Ohms - (1V Position) Gain Select and Sensitivity 23dB - 3.4Vin = 300W @ 8 Ohms - (2V Position) 17dB - 6.8Vin = 300W @ 8 Ohms - (4V Position) Input Impedance 50 Kohms single ended 20 Kohms balanced ...

Page 16 - IMPORTANT SAFETY INSTRUCTIONS; Read these instructions.; BRYSTON LIMITED WARRANTY; Courier address: 677 NEAL DRIVE; PETERBOROUGH, ONTARIO; BRYSTON SERVICE in CANADA:

IMPORTANT SAFETY INSTRUCTIONS The lightning flash with arrowhead symbol within an equilateral triangle, is intended to aler t the user to the presence of un-insulated “dangerous voltage “ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to per...

Bryston 6B SST - Manual

Table of Contents:

Summary

Other Bryston Models