Bryston 7B SST - Manual - manualsarea.com

Page 2 - B SST Series Amplifier; Table of Contents; Back Cover

7B SST Series Amplifier Table of Contents General Introduction Page 1 DescriptionInstallation and Ventilation Rear Panel Input Settings/Connections Page 2 Setting Input Selector SwitchBalance Input Connector ConfigurationSetting Input Sensitivity Output Binding Posts Page 3 Front Panel Description P...

Page 3 - Thank you for choosing the; B SST SERIES mono block Power Amplifier; The

7B SST Series Amplifier 1 Introduction Thank you for choosing the 7B SST SERIES mono block Power Amplifier . Bryston welcomes any suggestions you may have, or comments regarding the operation of your amplifier. We consideryou, our customer, to be Bryston’s most important resource, and your opinion i...

Page 4 - Rear Panel Input / Output Connections; This input connector; Balanced input Vs Single ended input:

7B SST Series Amplifier 2 Rear Panel Input / Output Connections 1. Input Select Switch. Each SST channel gives the user the option of switching between either balanced input or single ended input. 2. Balanced Input connector. ( Imp. 20k ) This input connector accepts standard ‘XLR’ or 1/4” TRS . Use...

Page 5 - RED; in-phase amplifier output; BLUE; inverted-phase amplifier output; coin

7B SST Series Amplifier 3 6. Output binding posts. The RED binding post is the in-phase amplifier output . Connect to this post the (+) terminal on the loudspeaker. The BLUE binding post is the inverted-phase amplifier output . Connect to this post the (-) terminal on the loudspeaker. Note: At no ti...

Page 6 - Front Panel; indicates the amplifier has no power.

7B SST Series Amplifier 4 Front Panel 1. 'SST POWER' switch The front panel label 'SST POWER', is a touch sensitive membrane switch used to apply or remove a/c line power to thesoft start circuitry. Push firmly the center of the switch until the power-up sequence begins. Push again and the amplifier...

Page 7 - Power Control; strip; fig W

7B SST Series Amplifier 5 Power Control 1. Master circuit - breaker. The 7B SST amplifier uses a magnetic-trip circuit breaker (1) to protect the amplifier. This switch should be ‘OFF’ during installation. When switched ‘OFF’ all A/C power is removed from the amplifier, including standby power.The c...

Page 9 - Typical Band-pass Noise

7B SST Series Amplifier 9 - 1 3 0 -50 - 1 2 0 -110 - 1 0 0 -90 -80 -70 -60 d B u 20 5k 50 100 200 500 1k 2k H z - 1 2 0 +10 -110 - 1 0 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 + 0 d B r A RE F 150 W 8 OHMS 10k 130k 20k 30k 40k 50k 60k 70k 80k 90k 100k 110k 120k H z Typical Band-pass Noise Typical THD+N...

Page 10 - Typical Frequency Response 7BSST

10 -1 + 1 5 -0 +1 +2 +3 +4 +5 +6 +7 +8 +9 + 1 0 +11 + 1 2 + 1 3 + 1 4 deg 20 20k 50 100 200 500 1k 2k 5k 10k H z -1 +0.5 -0.9 -0.8 -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 +0 +0.1 +0.2 +0.3 +0.4 d B r A 20 50k 50 100 200 500 1k 2k 5k 10k 20k H z Typical Frequency Response 7BSST Typical Phase Response 4 oh...

Page 11 - Typical IMD Sweep

0 0.01 0.001 0.002 0.003 0.004 0.005 0.006 0.007 0.008 0.009 % 20 20k 50 100 200 500 1k 2k 5k 10k H z Typical THD+N Sweep 4 ohm 900w 8 ohm 600w 7B SST Series Amplifier 11 0 0.01 0.001 0.002 0.003 0.004 0.005 0.006 0.007 0.008 0.009 % 2k 20k 3k 4k 5k 6k 7k 8k 9k 10k H z Typical IMD Sweep 8 ohm 600w 4...

Page 12 - Damping Factor

12 0 800 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 D F 20 20k 50 100 200 500 1k 2k 5k 10k H z Damping Factor 8 ohm reference 7B SST Series Amplifier

Page 13 - > 60 volts per microsecond

7B SST Series Amplifier 13 Technical Specifications Power Output 600 watts per channel into 8 ohms 900 watts per channel into 4 ohms Gain Select and Sensitivity 29dB - 2.3Vin = 600W @ 8 Ohms - (1V Position)23dB - 4.6Vin = 600W @ 8 Ohms - (2V Position) Input Impedance 50 Kohms single ended20 Kohms ba...

Page 14 - BRYSTON 20 -YEAR WARRANTY; In the event of a defect or malfunction, Bryston

BRYSTON 20 -YEAR WARRANTY Bryston products are warranted to be free frommanufacturing defects for a minimum of twenty years from the original date of manufacture. Thisincludes parts, labour and return shipping to the first owner and all subsequent owners. Warrantycoverage is automatic and commences ...

Bryston 7B SST - Manual

Table of Contents:

Summary

Other Bryston Models