Bryston 9BSST - Manual - manualsarea.com

Page 2 - Table of Contents

9B SST FIVE CHANNEL POWER AMPLIFIER Table of Contents General Introduction Page 1 Instalation and Ventilation Rear Panel Input Settings/Connections Page 2 Setting Input Selector Switch Balance Input Connector Configuration Setting Polarity Setting Input Sensitivity Output Binding Posts and Polarity ...

Page 3 - BSST Five Channel Power Amplifier; The

9B SST FIVE CHANNEL POWER AMPLIFIER 1 Introduction Thank you for choosing the 9BSST Five Channel Power Amplifier . Bryston welcomes any suggestions you may have, or comments regarding the operation of your amplifier. We consider you, our customer, to be Bryston’s most important resource, and your op...

Page 4 - Rear Panel Input / Output Connections; gold plated; This input connector; The normal operating position is

9B SST FIVE CHANNEL POWER AMPLIFIER 2 Rear Panel Input / Output Connections 1. Input Select Switch. Each 9BSST channel gives the user the option of switching between either balanced input or single ended input. 2. Balanced Input connector. ( Imp. 20k ) This input connector accepts standard ‘XLR’ or ...

Page 5 - wrench

9B SST FIVE CHANNEL POWER AMPLIFIER 3 6. Output binding posts The RED binding post is connected to the amplifier output . Connect to this post the (+) terminal on the loudspeaker. The BLACK binding post is connected to signal ground . Connect to this post the (-) terminal on the loudspeaker. When th...

Page 6 - Front Panel; Each 9BSST channel has a LED

9B SST FIVE CHANNEL POWER AMPLIFIER 4 Front Panel 1. 'SST POWER' switch The front panel label 'ST POWER', is a touch sensitive membrane switch used to apply or remove A/C line power to the 9BSST circuitry. Push firmly the center of the switch until the power-up sequence begins. Push again and the 9B...

Page 7 - Power Control Panel; The circuit breaker must be ‘ON’; strip; figure W

9B SST FIVE CHANNEL POWER AMPLIFIER 5 Power Control Panel REAR POWER ENTRY PANEL 1. Master circuit - breaker. The 9BSST uses a magnetic-trip circuit breaker (1) to protect the amplifier. This switch should be ‘OFF’ when installing the 9BSST. When switched ‘OFF’ all A/C power is removed from the ampl...

Page 8 - Rack Mounting Instructions; TOP VIEW; DO NOT

9B SST FIVE CHANNEL POWER AMPLIFIER 6 Rack Mounting Instructions Removing the channels makes rack mounting far easier as the chassis will be much lighter. Before removing any screws from the 9BSST be sure the power cord is removed from the unit. Remove the screws indicated on the top and bottom view...

Page 9 - Typical 5.1 Home Theatre Setup

9B SST FIVE CHANNEL POWER AMPLIFIER 7 Typical 5.1 Home Theatre Setup Right Front Left Front Center Powered Subwoofer Right Rear Left Rear HOME THEATRE PROCESSOR 9BSST 5X120W/CH

Page 11 - Typical Frequency Response

9B SST FIVE CHANNEL POWER AMPLIFIER 9 Typical Band-pass Noise Typical THD+N Harmonic Content Power supply artifacts are all below -95 dBu balanced input with 23dB gain shown The harmonic content of the 9BSST is all even order. dBu: dB relative to a reference of 0.7746 Volts Typical Frequency Respons...

Page 12 - Damping Factor; Typical Crosstalk

Typical THD+N Sweep 4 ohm 200w 8 ohm 120w Typical IMD Sweep 8 ohm 120w 4 ohm 200w 9B SST FIVE CHANNEL POWER AMPLIFIER 10 Graph shows that distortion is essentially unaffected by load. 4v balanced input shown. Damping Factor 8 ohm reference Typical Crosstalk channel 2 reading with channels 1 & 3 ...

Page 13 - Technical Specifications

9B SST FIVE CHANNEL POWER AMPLIFIER 11 Technical Specifications Power Output 120 watts per channel into 8 ohms 200 watts per channel into 4 ohms Gain Select and Sensitivity 29dB - 1.1Vin = 120W @ 8 Ohms - (1V Position) 23dB - 2.2Vin = 120W @ 8 Ohms - (2V Position) 17dB - 4.4Vin = 120W @ 8 Ohms - (4V...

Page 14 - IMPORTANT SAFETY INSTRUCTIONS; Read these instructions.; BRYSTON LIMITED WARRANTY; Courier address: 677 NEAL DRIVE; PETERBOROUGH, ONTARIO; BRYSTON SERVICE in CANADA:

IMPORTANT SAFETY INSTRUCTIONS The lightning flash with arrowhead symbol within an equilateral triangle, is intended to aler t the user to the presence of un-insulated “dangerous voltage “ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to per...

Bryston 9BSST - Manual

Table of Contents:

Summary

Other Bryston Models