Bryston 3B SST - Manual - manualsarea.com

Page 2 - B SST and 4B SST Series Amplifiers; Table of Contents; Bridged Mode Instructions; Page 14

3B SST and 4B SST Series Amplifiers Table of Contents General Introduction Page 1 DescriptionInstalation and Ventilation Rear Panel Input Settings/Connections Page 2 Setting Input Selector SwitchBalance Input Connector ConfigurationSetting Input Sensitivity Output Binding Posts Page 3 Front Panel De...

Page 3 - Thank you for choosing an; SST SERIES Stereo Power Amplifier; The

3B SST and 4B SST Series Amplifiers 1 Introduction Thank you for choosing an SST SERIES Stereo Power Amplifier . Bryston welcomes any suggestions you may have, or comments regarding the operation of your amplifier. We consideryou, our customer, to be Bryston’s most important resource, and your opini...

Page 4 - Rear Panel Input / Output Connections; This input connector; Balanced input Vs Single ended input:; RCA PLUG

3B SST and 4B SST Series Amplifiers 2 Rear Panel Input / Output Connections 1. Input Select Switch. Each SST channel gives the user the option of switching between either balanced input or single ended input. 2. Balanced Input connector. ( Imp. 20k ) This input connector accepts standard ‘XLR’ or 1/...

Page 5 - RED; amplifier output; BLACK; signal ground; coin; Coin

3B SST and 4B SST Series Amplifiers 3 6. Output binding posts. The RED binding post is connected to the amplifier output . Connect to this post the (+) terminal on the loudspeaker. The BLACK binding post is connected to signal ground . Connect to this post the (-) terminal on the loudspeaker. The Ou...

Page 6 - Front Panel; indicates channel has no power.

3B SST and 4B SST Series Amplifiers 4 Front Panel 1. 'SST POWER' switch The front panel label 'SST POWER', is a touch sensitive membrane switch used to apply or remove a/c line power to thesoft start circuitry. Push firmly the center of the switch until the power-up sequence begins. Push again and t...

Page 7 - Power Control; fig W

3B SST and 4B SST Series Amplifiers 5 Power Control 1. Master circuit - breaker. The SST amplifier uses a magnetic-trip circuit breaker (1) to protect the amplifier. This switch should be ‘OFF’ during installation. When switched ‘OFF’all A/C power is removed from the amplifier, including standby pow...

Page 9 - Typical Band-pass Noise 3BSST

3B SST and 4B SST Series Amplifiers 9 Typical Band-pass Noise 3BSST Typical THD+N Harmonic Content 3BSST Power supply artifacts are all below -95 dBu balanced input with 23dB (2v) gain shown The harmonic content of the 3BSST is all even order. dBu: dB relative to a reference of 0.7746 Volts The harm...

Page 10 - Typical Phase Response 3BSST

3B SST and 4B SST Series Amplifiers 10 Typical Phase Response 3BSST 4 ohm 400w 8 ohm 250w Typical Frequency Response 3BSST 8 ohm 150w 4 ohm 250w Typical Phase Response 4BSST 4 ohm 400w 8 ohm 250w 8 ohm 300w Typical Frequency Response 4BSST 4 ohm 500w

Page 11 - Typical THD+N Sweep 3BSST; Typical IMD Sweep 3BSST

Typical THD+N Sweep 3BSST 4 ohm 250w 8 ohm 150w 3B SST and 4B SST Series Amplifiers 11 Typical IMD Sweep 3BSST 8 ohm 150w 4 ohm 250w Graph shows that distortion isessentially unaffected by load.2v balanced input shown. Typical THD+N Sweep 4BSST 4 ohm 500w 8 ohm 3000w Typical IMD Sweep 4BSST 8 ohm 30...

Page 13 - > 60 volts per microsecond

3B SST and 4B SST Series Amplifiers 13 3BSST Technical Specifications 4BSST Power Output 150 watts per channel into 8 ohms 250 watts per channel into 4 ohms Gain Select and Sensitivity 29dB - 1.3Vin = 150W @ 8 Ohms - (1V Position)23dB - 2.6Vin = 150W @ 8 Ohms - (2V Position) Input Impedance 50 Kohms...

Page 14 - OPERATING BRYSTON 3B & 4B AMPLIFIERS IN BRIDGED MODE; channels

OPERATING BRYSTON 3B & 4B AMPLIFIERS IN BRIDGED MODE “Bridged mode” refers to the combining or “bridging” of two amplifier channels into a single ampli-fier channel. The primary reason for doing this is to achieve a single amplifier channel with much greater output power. When two 3B channels or...

Page 15 - BRYSTON 20 -YEAR WARRANTY; PETERBOROUGH, ONTARIO

BRYSTON 20 -YEAR WARRANTY Bryston products are warranted to be free frommanufacturing defects for a minimum of twentyyears from the original date of manufacture. Thisincludes parts, labour and return shipping to thefirst owner and all subsequent owners. Warrantycoverage is automatic and commences wi...

Bryston 3B SST - Manual

Table of Contents:

Summary

Other Bryston Models