Bromic BH0920001-1 - User Manual

Page 2 - IMPORTANT INSTRUCTIONS; DANGER, WARNING, IMPORTANT; Correct disposal of this product

2 bromic.com ! IMPORTANT INSTRUCTIONS This manual contains important information about the installation, operation, and maintenance of Eclipse Smart-Heat TM Electric Heaters. Please pay close attention to the important safety information shown throughout this instruction manual. Any safety informati...

Page 3 - CONTENT

3 bromic.com CONTENT IMPORTANT NOTES & WARNINGS 4-5 PRODUCT OVERVIEW 6 PRODUCT DESCRIPTION 6 SPECIFICATIONS 6 PRODUCT FEATURES 6 KEY DIMENSIONS & CLEARANCES 7 INSTALLATION INSTRUCTIONS - CEILING MOUNTED HEATER 8-14 BOX CONTENTS 8-9 WARNING 9 INSTRUCTIONS FOR SINGLE POLE OPTIONS 10-11 INSTRUC...

Page 4 - IMPORTANT NOTES & WARNINGS; WARNING

4 bromic.com IMPORTANT NOTES & WARNINGS WARNING • IMPORTANT - Installation MUST be carried out by a licensed electrical contractor. • Heater must be installed by 2 persons. • Improper installation, adjustment, or alteration and failure to follow the warnings and instructions in this manual could...

Page 5 - IMPORTANT NOTES AND WARNINGS; CONTINUED; SAVE THESE INSTRUCTIONS

5 bromic.com • In case of direct connection to a supply line, a bipolar circuit breaker with contact opening distance of at least 1/8 inch must be fitted upstream from the supply line. Contact an authorised service technician if you are unsure if you have a circuit breaker installed on the premises....

Page 6 - SPECIFICATIONS

6 bromic.com PRODUCT DESCRIPTION PRODUCT FEATURES PRODUCT SPECIFICATIONS SPECIFICATIONS Model Eclipse Smart-Heat TM Electric Part No (Heater Eclipse Pendant USA/CAN) BH0920001-1 Part No (Straight Ceiling Mount Pole 8”) BH3230001 Part No (Straight Ceiling Mount Pole 24”) BH3230002 Part No (Twin Strai...

Page 7 - KEY DIMENSIONS & CLEARANCES; adjacent materials are protected.; Inches

7 bromic.com KEY DIMENSIONS & CLEARANCES The stated clearance to combustible materials represents surface temperature of 117°F above room temperature. Building material with a low heat tolerance (such as plastic, vinyl siding, canvas, tri-ply etc.) may subject to degradation at lower temperature...

Page 8 - INSTALLATION INSTRUCTIONS - CEILING MOUNTED HEATER; Box 1 Contents; Eclipse Head Assembly

8 bromic.com INSTALLATION INSTRUCTIONS - CEILING MOUNTED HEATER Contents Packed in (3) Boxes Box 1 Contents Box 2 Contents Eclipse Head Assembly Including pre-assembled 2 x Dome Head Screws (M4 - Length: 6mm) Pendant Pole Assemblyone of the following styles:• Twin Straight Ceiling Mount Pole 24”• Cu...

Page 9 - Bolts for fastening to Ceiling surface; IMPORTANT; Eclipse Pendant Control; Caution – Glass – Handle with care

9 bromic.com INSTALLATION INSTRUCTIONS - CEILING MOUNTED HEATER CONTINUED... Tools/Parts Required (not Included) • Bolts for fastening to Ceiling surface • Phillips Head Screw Driver • Step Ladder • 2 strong people to help with lifting & assembly • Spirit Level WARNING This heater MUST be instal...

Page 10 - Instructions for Single Pole options, including:; Attach the chosen Ceiling Mount Pole to the; Fasteners must be chosen by installer to suit

10 bromic.com 4. Slide the Round Cap over the Ceiling Mount Pole and attach the it to the Roof Bracketusing 2 X Dome Head Screws (M4 - Length:10mm). 1. Unpack all items from shipping cartons and place items on a non-abrasive surface. To protect appliance do not removecardboard packaging from head as...

Page 11 - Insert the Heater Bracket into the Ceiling; Feed the cable through the Ceiling Mount; Heavy Item. Min Two Person Lift. Maximum; Fully insert additional 2 X Dome Head Screws; All packaging materials must be removed before

11 bromic.com 6. Insert the Heater Bracket into the Ceiling Mount Pole by hooking the attached 2XDome Head Screws (M4 - Length: 6mm) intothe slot feature in the Pole. Note: Screws are pre-assembled to heaterhead bracket. INSTALLATION INSTRUCTIONS - CEILING MOUNTED HEATER CONTINUED... 5. Feed the cab...

Page 12 - Unpack all items from shipping cartons and; Place the Twin Pole Cap loosely onto the Twin

12 bromic.com Instructions for Twin Pole option: • Twin Straight Ceiling Mount Pole 24” 1. Unpack all items from shipping cartons and place items on a non-abrasive surface. To protect appliance do not removecardboard packaging from head assemblyuntil it is mounted to ceiling. 2. Fasten the Twin Pole...

Page 15 - Installation Instructions – Wall Mounted Heater; INSTALLATION INSTRUCTIONS - WALL MOUNTED HEATER

15 bromic.com Installation Instructions – Wall Mounted Heater Box 1 Contents Box 2 Contents Eclipse Head Assembly Including pre-assembled2 x Dome Head Screws (M4 - Length: 6mm) Wall Mount Pole Instruction Manual (This Document) Wall Bracket Wall Bracket Cover INSTALLATION INSTRUCTIONS - WALL MOUNTED...

Page 18 - Instructions for Wall Mounted option:; Mount the Wall Bracket on the wall in the

18 bromic.com Instructions for Wall Mounted option: 1. Unpack all items from shipping cartons and place items on a non-abrasive surface. To protect appliance do not remove cardboardpackaging from head assembly until it ismounted to ceiling. 3. Slide the Wall Bracket Cover over the Wall Bracket. INST...

Page 21 - into Wall Cavity

21 bromic.com 9. Fasten the Wall Mount Pole to the Wall Bracket using 1 X Round Head Hex Screw(M8 - Length: 15mm). 8. Attach the Wall Mount Pole to the Wall Bracket. Feed the cable through the backslot of the Wall Mount into the wall cavity,or alternatively, the cable can be fed outof the optional C...

Page 23 - ELECTRICAL SHOCK HAZARD!

23 bromic.com/heat 23 ELECTRICAL INSTALLATION – PENDANT HEATERS bromic.com IMPORTANT NOTES & WARNINGS WARNING DANGER IMPORTANT This heater MUST be installed by an authorised/licenced person. Do not perform maintenance, or carry out installation or assembly procedure while electrical power is swi...

Page 24 - ELECTRICAL INSTALLATION – PENDANT HEATERS CONTROL; Open cover to the Pendant Control Box, by; The Power source MUST NOT be live when; DANGER; ambient temperature does not exceed 86°F.

TRANSFORMER MEANWELL (LPF-25-24) HEATER CONTROL PC B EMI FILTE R (YB22D1-3A-W) LED PCB DIMME R DC OUT 2 4V WHITE 2 4V DC RED 24V DC GREEN/YELLO W GREEN/YELLO W GROUND N/ A N/ A L L(N) BL UE L(N) BL UE BL UE BL UE BL UE LINE LO AD BROWN BROW N BROW N BROWN L G G G L(N) L 2 3 4 5 6 7 8 9 1 BLACK 2 4V ...

Page 25 - Mount the Pendant Heater Control to; The controller must be installed in a space with

Power cable from controller (Supplied with controller) Junction box & terminals (Provided by installer) Power cable from heater (Supplied with heater) WHITE 24V DC WHITE 24V DC GREEN/YELLOW GREEN/YELLOW GREY 240V GREY 240V BLUE BLUE BLACK 240V BLACK 240V BROWN 24V DC BROWN 24V DC +24V DC G -24V ...

Page 26 - FOR INSTALLATION USING; (Bromic Eclipse Pendant Control supplied separately); PENDANT HEATER CONTROL WIRING DIAGRAM

WHITE 24V DC WHITE 24V DC GREEN/YELLOW GREEN/YELLOW GREY 240V GREY 240V BLUE BLUE BLACK 240V BLACK 240V BROWN 24V DC BROWN 24V DC +24V DC G -24V DC L2 N L1 TRANSFORMER MEANWELL (LPF-25-24) HEATER CONTROL PCB EMI FILTER (YB22D1-3A-W) LED PCB DIMMER DC OUT 24V WHITE 24V DC RED 2 4V DC GREEN/YELLO W GR...

Page 28 - OPERATING INSTRUCTIONS; TURNING THE APPLIANCE ON; (SUPPLIED WITH BROMIC ECLIPSE PENDANT CONTROL); TURNING THE APPLIANCE OFF

28 bromic.com OPERATING INSTRUCTIONS TURNING THE APPLIANCE ON REMOTE CONTROL FUNCTIONS (SUPPLIED WITH BROMIC ECLIPSE PENDANT CONTROL) 1. Using the Remote Control, select the desired Heater setting: • Heater 100% - Heater output at full (100%).• Heater 66% - Heater output at 66% of total.• Heater 33%...

Page 29 - REMOTE CONTROL BATTERY; WARNING: MUST ONLY BE SERVICED BY LICENSED &

29 bromic.com OPERATING INSTRUCTIONS REMOTE CONTROL BATTERY • Keep the batteries out of reach of childrem. • Call a doctor immediately if a battery is swallowed. • Explosion hazard if the battery is substituted incorrectly. • Replace the battery with a CR2430 type battery only. • Battery is not rech...

Page 30 - PAIRING REMOTE CONTROL TO LED PCB (BOTTOM 3 BUTTONS OF REMOTE).

30 bromic.com OPERATING INSTRUCTIONS WARNING: MUST ONLY BE SERVICED BY LICENSED & AUTHORIZED TECHNICIAN. 1. Open cover to the Pendant Control Box, by removing 6x Oval head screws (#4-40 - Length: 1/2”) from the cover. 2. Locate the small black button on the small LED PCB (shown in image on right...

Page 31 - MAINTENANCE; DO NOT

31 bromic.com MAINTENANCE & SERVICING IMPORTANT NOTES & WARNINGS MAINTENANCE WARNING This heater MUST be installed by an authorised/ licenced person. Do not perform maintenance, or carry out installation or assembly procedure while electrical power is switched on. ! IMPORTANT Check product l...

Page 32 - TROUBLESHOOTING; REPLACEMENT PARTS; SYMPTOM; Part Number

32 bromic.com TROUBLESHOOTING REPLACEMENT PARTS SYMPTOM POSSIBLE CAUSE (S) CORRECTIVE ACTION No heat 1. Incorrect heater setting chosen2. Incorrect Voltage.3. No power.4. No/low batteries in remote.5. Remote too far.6. Radio interference.7. Remote not paired or faulty control. 1. Choose heat setting...

Bromic BH0920001-1 - User Manual

Table of Contents:

Summary

Other Bromic Heaters Models