Bromic 2620251 - User Manual

Page 2 - IMPORTANT; Correct Disposal of this product

2 bromic.com/heating-au Head Office: 10 Phiney Place, Ingleburn, NSW 2565 Australia Telephone: 1300 276 642 (within Australia) or +61 2 9748 3900 (from overseas) Fax: +61 2 9748 4289 Email: [email protected] Web: www.bromic.com/heating-au ! IMPORTANT This manual contains important information about ...

Page 3 - CONTENTS

3 bromic.com/heating-au CONTENTS IMPORTANT NOTES & WARNINGS 4 PRODUCT OVERVIEW 5 PRODUCT DESCRIPTION 5 SPECIFICATIONS 5 PRODUCT FEATURES 5 HEATER INSTALLATION INSTRUCTIONS 6 CEILING & WALL MOUNTING 6 CEILING RECESS 9 TUBE SUSPENSION 10 ELECTRICAL INSTALLATION 11 SERVICING 11 TROUBLESHOOTING ...

Page 4 - IMPORTANT NOTES AND WARNINGS

4 bromic.com/heating-au IMPORTANT NOTES AND WARNINGS WARNING • IMPORTANT - Installation MUST be carried out by a licensed and authorised person. • Improper installation, adjustment, or alteration and failure to follow the warnings and instructions in this manual could result in severe personal injur...

Page 5 - CONTINUED; SPECIFICATIONS

5 bromic.com/heating-au or swimming pool. Any switches or controls must not be within reach of a person in the bathtub, shower or swimming pool. • To maintain Ingress Protection Rating (IPX4), only IP44rated conduit fittings should be used for electricalinstallation. • This product does not have a s...

Page 6 - HEATING INSTALLATION INSTRUCTIONS; CEILING & WALL MOUNTING; WARNING - Outdoor Installation; MINIMUM DISTANCE BETWEEN

6 bromic.com/heating-au HEATING INSTALLATION INSTRUCTIONS • Heaters must be installed according to theminimum installation clearances shown in thesediagrams CEILING & WALL MOUNTING • Heaters must be away from the fourth wall. This heater MUST be permanently installed by an authorised/licenced pe...

Page 7 - Wall mount

7 bromic.com/heating-au HEATING INSTALLATION INSTRUCTIONS CONTINUED... OPTION 1 To exit the cable through the side of the wall mounting bracket, start from step 1. 1. Unscrew and remove plug-in wall bracket (a) . 2. Attach extra supplied cable gland into the samehole from the outside of the bracket....

Page 8 - Straight bracket option

8 bromic.com/heating-au HEATING INSTALLATION INSTRUCTIONS CONTINUED... 8. To fix heater at desired angle, fully insert M3x10mm positioning screws (included with wall bracket) onboth sides of mounting bracket whilst holding heater in the desired position (h). The heater can positioned straight, or be...

Page 9 - CLEARANCE TO COMBUSTIBLES OPTION 1

9 bromic.com/heating-au HEATING INSTALLATION INSTRUCTIONS CONTINUED... CEILING RECESS (SOLD SEPARATELY) ! WARNING The heater shall, under no circumstance, be covered with insulating material or similar material. ! WARNING Joists, beams and rafters shall not be cut or notched to install the heater. W...

Page 11 - TUBE SUSPENSION

11 bromic.com/heating-au HEATING INSTALLATION INSTRUCTIONS CONTINUED... 11. Attach the bracket end-cap to the wall bracket using the4 M5 screws and nuts provided (k). 12. Carefully remove the 4 M5 screws fastening the heatermounting bracket to the back of the heater. Be careful notto move or put any...

Page 12 - No heat; TROUBLESHOOTING

12 bromic.com/heating-au ELECTRICAL INSTALLATION ! WARNING This heater MUST be permanently installed by an authorised/licenced person. Do not perform maintenance, or carry out installation or assembly procedure while electrical power is switched on. 1. Check product label for correct voltage and wat...

Bromic 2620251 - User Manual

Table of Contents:

Summary

Other Bromic Heaters Models