Zanussi ZWG 7120 P- Manuals

Page 2 - General safety

Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Frost precaution _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Installation _ _ _ _ _ _ _ ...

Page 4 - Packaging materials

To activate this device, ro- tate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin. To disable this device and restore the possibility of closing the door, rotate the button anti-clockwise un- til the groove is vertical. Frost precaut...

Page 5 - Ecological hints; Product description

Ecological hints To save water, energy and to help protect the environment, we recommend that you follow these tips:• Normally soiled laundry may be washed without pre- washing in order to save detergent, water and time (the environment is protected too!). • The machine works more economically if it...

Page 6 - Installation; Unpacking

Water supply pressure Minimum Maximum 0,05 MPa 0,8 MPa Maximum Load Cotton 6 kg Spin Speed Maximum 1200 rpm (ZWG7120P) 1400 rpm (ZWG7140P) Installation Unpacking Warning!• Read carefully the "Safety information" chapter before installing the appliance. x 3 x 3 x 2 x 1 B A C Warning! Remove a...

Page 7 - Positioning and levelling

• Remove the power supply cable and the draining and inlet hose from the hose holders ( C ) on the rear of the appliance. • Unscrew the three bolts ( A ) and remove the hose holders ( C ). • Slide out the relevant plastic spacers ( B ). • Plug the smaller upper hole and the two large ones with the c...

Page 10 - Buzzer; Daily use; Sort out the laundry

First use • Ensure that the electrical and water connections comply with the installation instructions. • Ensure that the drum is empty.• Before the first wash, run a cotton cycle at the highest temperature without any laundry in the machine, to remove any manufacturing residue from the drum and tub...

Page 18 - At the end of the programme

9 Start the programme by pressing the button 9• To start the selected programme, press the button 9 , the corresponding green pilot light stops flashing. The pilot light 10 illuminates to indicate that the appliance starts operating and the door is locked. If you have chosen a delayed start, the app...

Page 19 - Door seal; Washing programmes; of Laundry

display go off. The green pilot light of the button 9 flashes with a low frequency. By pressing any button the appli- ance will come out of the energy saving status. Door seal At the end of every cycle, check from the door seal and remove objects that could be trapped in the fold. Washing programmes...

Page 21 - Consumption values

Programme - Maximum and Minimum Temperature - Cycle De- scription - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options Detergent Com- partment SPIN Drain and long spin at maximum spin speed: 1200 rpm for ZWG7120P - 1400 rpm for ZWG1740P Max. load 6 kg Separate spin for hand washed g...

Page 22 - Care and cleaning; Maintenance Wash

Programme Energy consumption (KWh) Water consumption (litres) Programme duration (Hours.Minutes) Cottons 60° 1.30 69 the display on the control panel. Cotton ECO 60° 1) 1.02 49 Cottons 40° 0.75 69 Synthetics 40° 0.60 57 Delicates 40° 0.60 65 Wool/ Handwash 30° 0.40 50 1) « Cotton Eco » at 60°C with ...

Page 23 - Cleaning the drain filter

• Use the previous brush to clean the recess, en- suring that upper and lower part of it is well cleaned. After having cleaned the dispenser and the drawer re- cess, replace it. Cleaning the drain filter The filter permits to hold fluff or foreign bodies left un- awares in the laundry. The pump must...

Page 24 - Cleaning the water inlet filters; What to do if...; Fault code and malfunction

Cleaning the water inlet filters Important! If the appliance doesn't fill, it takes a long time to fill with water, the starting button flashes red or the display (if available) shows the relevant alarm (see chapter "What to do if..." for more details), check if the water inlet filters are b...

Page 28 - Model description

The necessary data for the service centre is on the rating plate. We recommend that you write the data here: Mod. ... ... ... Pr od. No. ... ... ... Ser . No. ... ... ... Mo d . .. . ... .. . Pr od. N o . .. . ... . . S er . No . ... .. . ... Model description (MOD.) ............................... ...