Zanussi ZGG 782- Manuals

5 Operation Hob burners To light a burner: z push in the relevant control and turn it to maximumposition; z then adjust the flame as required. z If the burner does not ignite, turn the control knob tozero, and try again. If you use a saucepan which is smaller thanthe recommended size, the flame will...

6 Maintenance and Cleaning Before any maintenance or cleaning can be carriedout, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, asspillage can be removed more easily than if it isleft to cool. The Hob Top Regularly wipe over the hob top and ...

7 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service ForceCentre.IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation,a charge will be made even...

8 OVERALL DIMENSIONS ZGG 642 ZGG 782 Width: 580 mm. 680 mm. Depth: 510 mm. 510 mm. CUT OUT DIMENSIONS ZGG 642 ZGG 782 Width: 550 mm. 560 mm. Depth: 470 mm. 480 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V 50Hz supply, 3 core flexible cable with nonre...

9 Important safety requirements This hob must be installed in accordance with the GasSafety (Installation and Use) Regulations (Current Edition)and the IEE Wiring Regulations (Current Edition).For appliances installed in the Republic of Ireland pleaserefer to NSAI- Domestic Gas Installation I.S. 813...

10 Cut Out Size The dimensions of the cut-out are given in the diagram. 550 47 0 30 Rectangular cut-out size for hobDimensions are given in mm. FO 2038 FO 2098 ZGG 642 ZGG 782 A) End of shaft with nut B) Washer C) Elbow FO 0814 FO 0264 Installation IMPORTANT This hob must be installed by a competent...

11 Building In ON/OFF SWITCH FLEXOUTLET ON/OFF SWITCH FLEXOUTLET FO 0763 FO 0764 Dimensions are given in mm. FO 1013 3 Building over a cupboard ordrawer If the hob is to be installed above a cupboard or drawerit will be necessary to fit a heat resistant board belowthe base of the hob on the undersid...

12 ) Electrical connections Any electrical work required to install this hobshould be carried out by a qualified electrician orcompetent person, in accordance with the currentregulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should thesesafety measures not be observed. T...

14 Ignition System / Gas Ignition YES Check plug top fuseand replace ifnecessary Check polarity andearth continuity ofsupply point Check earth continuityof appliance Ignitor does not spark Check fitting of burners Check position of theelectrode Check by pass simmeradjusted Light burner manually Chec...

15 Commissioning When the hob has been fully installed it will be necessaryto check the minimum flame setting. To do this, followthe procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turnthe control knob from MIN to MAX several times...

16 Guarantee/Customer Service Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux applianceor any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our optionr...

17 This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the periodspecified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countrieslisted below the appliance guarantee will move wit...