Zanussi ZDF221S- Manuals

Indicator lights End of programme indicator light Illuminates when the washing programme has ended.Switch off the dishwasher by returning the programmeselector dial to the Off position. The On/Off indicatorlight turns off.It also has added functions of visual signalling as:– the setting of the water...

Programme Degree of soil Type of load Programme description E Rinse and Hold Any.Partial load (to be completed later in the day). 1 cold rinse (to avoid foodscraps from stickingtogether).This programme does notrequire the use of deter-gent. 1) Ideal for washing a partially loaded dishwasher. This is...

– Adjust the rinse aid dosage Set the water softener The dishwasher is equipped with a watersoftener designed to remove minerals and saltsfrom the water supply, which would have a det-rimental or adverse effect on the operation ofthe appliance.The higher the content of these minerals andsalts, the h...

Setting the water softener manually (see table) Set switch to position 1 or2 The water softener is factory set at position 2. Setting the water softener electronically (see table) The water softener is factory set at position 5.The dishwasher must be switched off . Press and hold the start/cancel bu...

Loading cutlery and dishes Sponges, household cloths and any object thatcan absorb water may not be washed in thedishwasher.• Before loading the dishes, you should: – Remove all left over food and debris.– Soften remnants of burnt food in pans • When loading the dishes and cutlery, please note:– Dis...

To move to the higher position proceed as follows: 1. Pull out the basket until it stops.2. Carefully lift both sides upwards until the mecha- nism is engaged and the basket is stable. To lower the basket to the original position proceedas follows: 1. Pull out the basket until it stops.2. Carefully ...

For programmes with pre-wash add an additionaldetergent dose in com-partment B . When using detergenttablets: place detergenttablets in compartment A . Close the lid. Unloading the dishwasher • Hot dishes are sensitive to knocks. The dishes should therefore be allowed tocool down before removing fro...

Clean filters A , B and C thoroughly under runningwater. Turn the handle about 1/4turn anticlockwise and re-move filters B and C . Remove filter A from the base of the washing com-partment. Put the flat filter A back in the base of the washingcompartment and ensurethat it fits perfectly underthe two...

2. Leave the door ajar to prevent the forma- tion of any unpleasant smells. 3. Leave the inside of the machine clean. Frost precautions Avoid placing the machine in a location wherethe temperature is below 0°C. If this isunavoidable, empty the machine, close the ap-pliance door, disconnect the water...

Something not working The dishwasher will not start or stops duringoperation.Certain problems are due to the lack of simplemaintenance or oversights, which can besolved with the help of the indications describedin the chart, without calling out an engineer. Switch off the dishwasher, open the door a...

Technical data Dimensions Width x Height x Depthcm 60,0 x 85,0x 61,0 Electrical connectionVoltage - Overall power - Fuse Information on the electrical connection is given on the rating plate on theinner edge of the dishwasher’s door. Water supply pressure Minimum - Maximum(MPa) 0,05 - 0,8 Capacity p...

Hints for test institutes Testing in accordance with EN 60704 must be carried out with appliance fully loaded and us-ing the test programme (see "Consumptionvalues").Test in accordance with EN 50242 must be carried out when the salt container and rinse aid dispenser have been filled with sal...

Drain hose Connect drain hose to thesink. Secure it with thesupplied hose clamp. Required height: 30 to 100cm above bottom of thedishwasher. Ensure that the hoses arenot kinked, crushed or en-tangled. When connecting thedrain hose to an undersink trap spigot, the entire plastic membrane (A)must be r...