Zanussi CF98- Manuals

TSE-P 02.01 LF 7/35 599 34 60-32 2. FUNCTIONAL CHARACTERISTICS 2.1 CONTROL PANEL ON/OFF KEY [ S0 ] Switches the dishwasher ON and OFF. When the LED [LD0] lights, this means that the appliance is switched on. 2.1.1 PROGRAMME AND OPTION KEYS [ S1 S2 S3 S4 S5 S6 ] Used to select a washing programme and...

TSE-P 02.01 LF 8/35 599 34 60-32 2.2 SUPPLEMENTARY OPTIONS (factory-set) 2.2.1 POSSIBLE OPTIONS: «DELAY» & «1/2 LOAD» (if featured) Only one option can be selected at a time («DELAY» or «1/2 LOAD»), never both. If featured, the option may be associated with keys [ S4 ] or [ S5 ] or [ S6 ]. 2.2.1...

TSE-P 02.01 LF 9/35 599 34 60-32 2.4 SELECTION OF PROGRAMMES 2.4.1 SELECTING THE CYCLE (with the door closed) Switch the dishwasher ON by pressing [ S0 ]; the “POWER ON” pilot lamp lights [LD0]. The SALT and RINSE-AID LEDs [LD13 LD14] may light. Press the key for the desired programme [ S1 S2 S3 ......

TSE-P 02.01 LF 10/35 599 34 60-32 2.5 SELECTING A PROGRAMME WITH THE DELAYED START OPTION 2.5.1 PROGRAMME SELECTION (with the door closed) Press [ S0 ] to switch the dishwasher on; the “POWER ON” LED [LD0] lights. Perform the procedure for selection of the programme / options as described in paragra...

TSE-P 02.01 LF 11/35 599 34 60-32 3. SPECIFICATIONS FOR ACTUATORS AND SENSORS 3.1 COMPONENTS TYPE OF COMPONENT POWER AVAILABLE TYPE OF CONTROL Wash pump Max 250W Triac & relay Drain pump Max 100W Triac & relay Washing heater Max 2100W Relay Water fill solenoid Max 10W Triac Regeneration sole...

TSE-P 02.01 LF 12/35 599 34 60-32 4 OPERATION OF THE WASH / DRAIN MOTOR 4.1 WASH MOTOR CHARACTERISTICS This dishwasher is fitted with a single-phase variable-speed asynchronous motor. A tachimetric sensor, fitted to the interior of the motor, constantly monitors the speed of the motor,which is trans...

TSE-P 02.01 LF 13/35 599 34 60-32 4.3 WASHING SYSTEM This appliance features the conventional washing system, in which the mechanical action is obtainedby the rotation of the single motor. This drives the water into the hydraulic circuit and actions the twospray arms simultaneously. DEFINITION OF TH...

TSE-P 02.01 LF 14/35 599 34 60-32 4.5 5. HYDRAULIC CIRCUIT KEY 1. Anti-flooding device 11. Sump 2. Anti-overflow device 12. Pressure switch 3. Fill solenoid 13. Connector siphon for anti-overflow device 4. Air-Break 14. Cutting valve sump 5. Intake valve for regeneration chamber 15. Wash motor 6. Re...

TSE-P 02.01 LF 15/35 599 34 60-32 5.1 WATER FILL - FUNCTIONAL SYSTEM For dishwashers fitted with motors with tachimetric sensors (1.5 New Generation models), theelectronic control system is designed to control the water fill by identifying the signals received fromthe pressure switch (which thus act...

TSE-P 02.01 LF 17/35 599 34 60-32 5.2.6 WATER FILL TIMEDuring the entire duration of the fill phase (i.e. from sub-phase 5.2.1 to sub-phase 5.2.4), the solenoidvalve may remain in the open position for a maximum overall time of 4 minutes. Within this period, the system detects whether the pressure s...

TSE-P 02.01 LF 18/35 599 34 60-32 5.4 CONTROL OF DRAIN CYCLE When the washing cycle ends, the appliances passes to the drain phase. In this phase, in order to ensure that the hydraulic circuit is empty before the start of the subsequentphase (water fill), a control procedure is carried out at the en...

TSE-P 02.01 LF 19/35 599 34 60-32 5.5 SPECIAL REGENERATION CYCLE With the new water softening system, the “special regeneration” process is controlled electronically,and is subdivided into 5 levels as follows: REGENERATION VALUES LEVEL INDICATION WASHING CYCLE FILL PHASES WATER HARDNESS DEFINITION L...

TSE-P 02.01 LF 20/35 599 34 60-32 6 «ACTIVE» DRYING SYSTEM The “Active Plus” drying system features a close integrated circuit with bidirectional convectivemovement ; air is drawn in from the exterior thus allowing the circulation of the inner warm air. 6.1 DEFINITION OF THE SYSTEMThe drying system ...

TSE-P 02.01 LF 23/35 599 34 60-32 7.4 DESCRIPTION OF SAFETY FEATURES AND ALARMS 7.4.1 WATER FILL TIME-OUT ALARM [A L 5] Led [ LD9 ] This Time-out is activated only during the water fill phases. Ä The control system definitively switches off the fill solenoid valve. Ä Counting of time “T” starts when...

TSE-P 02.01 LF 24/35 599 34 60-32 7.4.3 ANTI-FLOODING CONTROL SYSTEM ALARM [A L 4] Leds [ LD9 ] + [ LD10 ] This control system is operative during the washing phases only, and not in the water fill phases, inwhich case is it connected to the safety device (see paragraph 7.4.1 “W ater Fill Time-out”)...

TSE-P 02.01 LF 27/35 599 34 60-32 8 . ELECTRICAL FUNCTIONS 8.1 CIRCUIT DIAGRAM

TSE-P 02.01 LF 28/35 599 34 60-32 8.2 BASIC ELECTRICAL DIAGRAM

T SE-P 02 .01 LF 29/35 599 34 60-32 8.3T A B L E OF W A S H IN G PROGR A M M E S T he table lis ts al l the pr o gr am m es s tor ed in mem or y. The c odes ( A , B etc.) i den tif y t he pr o gr am m es assigned ( m ax . 5) to the indiv id ual appl ia nc es . Pre- w ash M ain w ash First rinse S ec...

TSE-P 02.01 LF 30/35 599 34 60-32 9. SERVICING 9.1 COMPONENT DIAGNOSTICS This test is used by service engineers only to check the efficiency of the main electrical components.To access the test procedure, it is necessary to press a combination of keys. Correct operation of thecomponents to be tested...

TSE-P 02.01 LF 31/35 599 34 60-32 9.2 FUNCTIONAL TESTING CYCLE The functional testing cycle is an abbreviated washing programme for use by service engineers only.The testing cycle enables the engineer to check all the functions which make up a traditional washingcycle (in effect, the test simulates ...

TSE-P 02.01 LF 32/35 599 34 60-32 9.3 CHECKING THE EFFICIENCY OF THE COMPONENTS In order to facilitate testing of the components, a TEST PROCEDURE has been created showing thecontacts to which the probes of the tester should be connected and the theoretical reading for eachcomponent. 9.3.1 PROCEDURE...

TSE-P 02.01 LF 33/35 599 34 60-32 9.3.2 COMPONENT CONNECTION DIAGRAM