Xantrex XPF 35-10 - Manuals

Safety This power supply is a Safety Class I instrument according to IEC classification and has been designed to meet the requirements of EN61010-1 (Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use). It is an Installation Category II instrument intended for op...

EMC This instrument has been designed to meet the requirements of the EMC Directive 89/336/EEC. Compliance was demonstrated by meeting the test limits of the following standards: Emissions EN61326 (1998) EMC product standard for Electrical Equipment for Measurement, Control and Laboratory Use. Test ...

Installation Mains Operating Voltage Check that the instrument operating voltage marked on the rear panel is suitable for the local supply. Should it be necessary to change the operating voltage, proceed as follows: 1. Ensure that the instrument is disconnected from the AC supply. 2. Remove the 6 sc...

Connections All connections are made from the front panel. The load should be connected to the positive (red) and negative (black) terminals marked OUTPUT. The OUTPUT terminals are rated at 15A. Remote sense connections to the load, if required, are made from the positive (+) and negative ( − ) SENS...

Operation The operation of both outputs is identical; the following description applies to both. Setting Up the Output With the POWER switch on ( l ) and the OUTPUT switch off the output voltage and current limit can be accurately preset using the VOLTAGE and CURRENT controls; the upper meter shows ...

Connection to the Load The load should be connected to the positive (red) and negative (black) OUTPUT terminals. Both are fully floating and either can be connected to ground. Remote Sensing The unit has a very low output impedance, but this is inevitably increased by the resistance of the connectin...

Even with the output off the load is still connected to the power supply output stage. Do not apply external voltages in excess of 50V to the power supply terminals or damage may result. The output is protected from reverse voltages by a diode; the continuous reverse current must not exceed 3 Amps, ...

Calibration Allow at least 5 minutes warm-up before commencing calibration. Access to Calibration Adjustments All adjustments are on the control board, which is mounted above the main (power) board, except where stated. To gain access to the board it is necessary to remove the top cover. WARNING! Wh...

Voltage Calibration Connect DMM, set to Volts, across output. Set voltage controls to minimum and current control to maximum. Switch output ON and check for a reading of 00·00V ± 0·01V on display and DMM. Set voltage controls to maximum. Adjust VR16/VR116 (maximum output volts) for a reading of 35·3...

Sécurité Cet instrument est de Classe de sécurité 1 suivant la classification IEC et il a été construit pour satisfaire aux impératifs EN61010-1 (impératifs de sécurité pour le matériel électrique en vue de mesure, commande et utilisation en laboratoire). Il s'agit d'un instrument d'installation Cat...

Installation Tension d’utilisation secteur Vérifier que la tension opérationnelle de l'instrument indiquée sur le panneau arrière est appropriée pour l'alimentation locale. S'il s'avère nécessaire de modifier la tension opérationnelle, procéder de la manière décrite ci-dessous: 1. S'assurer que l'in...

Connexions Toutes les connexions sont effectuées au panneau avant. Relier la charge aux bornes positive (rouge) et négative (noire) marquées OUTPUT (Sortie). Les bornes de sortie ont une intensité nominale de 15 A. Effectuer des connexions de télédétection à la charge, le cas échéant, des bornes de ...

les valeurs directement sur l’affichage de l’utilisateur. Si, pour une raison quelconque, la tension de sortie dépasse la tension de protection OVP préréglée, y compris la tension forcée de manière externe, il se produira un déclenchement de la sortie. Il se produira également un déclenchement de la...

Sicherheit Dieses Gerät wurde nach der Sicherheitsklasse (Schutzart) I der IEC-Klassifikation und gemäß den europäischen Vorschriften EN61010-1 (Sicherheitsvorschriften für elektrische Mess-, Steuer, Regel- und Laboranlagen) entwickelt. Es handelt sich um ein Gerät der Installationskategorie II, das...

Installation Netzbetriebsspannung Sicherstellen, dass die auf der Geräterückwand angegebene Betriebsspannung mit der Versorgungsspannung am Ort übereinstimmt. Falls es erforderlich ist, die Betriebsspannung zu ändern, wie folgt vorgehen: 1. Sicherstellen, dass das Gerät vom Wechselstromnetz getrennt...

Anschlüsse Sämtliche Anschlüsse erfolgen von der Fronttafel aus. Der Verbraucher sollte an die mit AUSGANG (OUTPUT) markierte positive (rote) und negative (schwarze) Klemme angeschlossen werden. Die AUSGANGS-Klemmen sind für eine Stromstärke von 15 A ausgelegt. Istwert-Fernerfassungs-Anschlüsse zum ...

Wartung Die Hersteller bzw. deren Vertretungen im Ausland bieten die Reparatur von Geräten an, bei denen eine Störung aufgetreten ist. Wenn der Eigentümer die Wartungsarbeiten selbst durchführen möchte, hat er dafür Sorge zu tragen, dass diese Arbeiten ausschließlich von entsprechend qualifiziertem ...

Sicurezza Questo strumento appartiene alla Categoria di Sicurezza 1 secondo la classifica IEC ed è stato progettato in modo da soddisfare i criteri EN61010-1 (requisiti di Sicurezza per Apparecchiature di misura, controllo e per uso in laboratorio). E’ uno strumento di Categoria II di installazione ...

Installazione Tensione d’esercizio Controllare che la tensione d’esercizio dello strumento segnata sul pannello posteriore sia uguale a quella della rete elettrica locale. Se dovesse rendersi necessario cambiare la tensione d'esercizio, osservare il seguente procedimento: 1. Controllare che lo strum...

Collegamento Tutti i collegamenti si fanno dal pannello frontale. Il carico va collegato ai morsetti positivo (rosso) e negativo (nero) contrassegnati OUTPUT (uscita). I morsetti OUTPUT (uscita) hanno una portata nominale di 15A. L’allacciamento al carico di sensori a distanza, se richiesto, va coll...

Limite di potenza L’uscita massima a tensioni diverse è delimitata dall’inviluppo di potenza illustrato di seguito. L’inviluppo di potenza è impostato per dare 35V/5A e 12V/10A sotto tutte le condizioni di carico (ambedue le uscite sotto carico); a tensioni in uscita più basse la potenza in uscita v...

Manutenzione I Produttori o i loro agenti all’estero faranno le riparazioni necessarie in caso di guasto. Qualora l’utente desiderasse eseguire il lavoro di manutenzione, tale lavoro deve essere fatto solo da personale qualificato e usando il manuale di servizio che può essere acquistato direttament...

Seguridad Este es un instrumento de Clase de Seguridad I según la clasificación del IEC y ha sido diseñado para cumplir con los requisitos del EN61010-1 (Requisitos de Seguridad para Equipos Eléctricos para la Medición, Control y Uso en Laboratorio). Es un instrumento de Categoría de Instalación II ...

Instalación Voltaje de trabajo de alimentación Verificar que el voltaje de trabajo de alimentación que figura en el panel posterior concuerde con el suministro local. Si fuese necesario cambiar la gama de voltajes de trabajo , proceda de la siguiente manera: 1. Cerciorarse de que el instrumento esté...

Conexiones Todas las conexiones se efectuan desde el panel delantero. La carga debe conectarse a los bornes positivos (rojos) y negativos (negros) marcados OUTPUT (salida). Los bornes de OUTPUT están clasificados a 15A. Las conexiones a la carga del sensor remoto , si requeridas, se efectuan desde l...

La envoltura de potencia está fijada para producir 35V/5A y 12V/10A bajo toda condición de suministro (con ambas salidas cargadas); para salidas de voltaje inferiores, la potencia de salida está limitada por la corriente máxima de 10A. Al superar el límite de potencia, el indicador de estado cambiar...

Protección La protección contra sobrecarga de tensión (OVP ) es totalmente variable dentro de la gama de 10% a 110% del nivel de salida máximo de la salida. El límite de OVP se fija mediante el potenciómetro prefijado SET OVP, ajustable por destornillador, accedible por medio de un agujero en el pan...

Warranty Information Warranty What does this warranty cover? This Limited Warranty is provided by Xantrex Technology, Inc. ("Xantrex") and covers defects in workmanship and materials in your XPF series. This warranty lasts for a Warranty Period of three years (3 years) from the date of purch...

What does this warranty not cover? This Limited Warranty does not cover normal wear and tear of the product or costs related to the removal, installation, or troubleshooting of the customer's electrical systems. This warranty does not apply to and Xantrex will not be responsible for any defect in or...

Return Material Authorization Policy Before returning a product directly to Xantrex you must obtain a Return Material Authorization (RMA) number and the correct factory "Ship To" address. Products must also be shipped prepaid. Product shipments will be refused and returned at your expense if...