Page 2 - Disclaimer; Part Number
About Xantrex Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with products from 50 watt mobile units to one MW utility-scale systems for wind, solar, batteries, fuel cells, microturbines, and backup power applications in both grid-connected and stand-a...
Page 3 - Table of Contents
Table of Contents Specification 3 Safety 5 EMC 6 Installation 7 Connections 8 Operation 9 Maintenance 11 Calibration 12 Instructions en Francais Sécurité Installation 13 Connexions 14 Opération 14 Maintenance 16 Bedienungsanleitung auf Deutsch Sicherheit 17 Installation 18 Anschlüsse 19 Betrieb 19 W...
Page 4 - Specification; OUTPUT SPECIFICATIONS
Specification OUTPUT SPECIFICATIONS Voltage Range: 0V to 35V Current Range: 0A to 10A Power Range: Up to 175W Output Voltage Setting: By coarse and fine controls. Output Current Setting: By single logarithmic control. Operating Mode: Constant voltage or constant current with automatic cross-over pro...
Page 6 - Safety
Safety This power supply is a Safety Class I instrument according to IEC classification and has been designed to meet the requirements of EN61010-1 (Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use). It is an Installation Category II instrument intended for op...
Page 7 - EMC; Emissions; Cautions
EMC This instrument has been designed to meet the requirements of the EMC Directive 89/336/EEC. Compliance was demonstrated by meeting the test limits of the following standards: Emissions EN61326 (1998) EMC product standard for Electrical Equipment for Measurement, Control and Laboratory Use. Test ...
Page 8 - Installation; Mains Operating Voltage; Mounting
Installation Mains Operating Voltage Check that the instrument operating voltage marked on the rear panel is suitable for the local supply. Should it be necessary to change the operating voltage, proceed as follows: 1. Ensure that the instrument is disconnected from the AC supply. 2. Remove the 6 sc...
Page 9 - Connections
Connections All connections are made from the front panel. The load should be connected to the positive (red) and negative (black) terminals marked OUTPUT. The OUTPUT terminals are rated at 15A. Remote sense connections to the load, if required, are made from the positive (+) and negative ( − ) SENS...
Page 10 - Operation; Setting Up the Output; Constant Voltage; Constant Current; Instantaneous Current Output
Operation The operation of both outputs is identical; the following description applies to both. Setting Up the Output With the POWER switch on ( l ) and the OUTPUT switch off the output voltage and current limit can be accurately preset using the VOLTAGE and CURRENT controls; the upper meter shows ...
Page 11 - Series or Parallel connection with other units
Connection to the Load The load should be connected to the positive (red) and negative (black) OUTPUT terminals. Both are fully floating and either can be connected to ground. Remote Sensing The unit has a very low output impedance, but this is inevitably increased by the resistance of the connectin...
Page 12 - Ventilation; Maintenance; Fuse; Cleaning
Even with the output off the load is still connected to the power supply output stage. Do not apply external voltages in excess of 50V to the power supply terminals or damage may result. The output is protected from reverse voltages by a diode; the continuous reverse current must not exceed 3 Amps, ...
Page 13 - Calibration; Access to Calibration Adjustments; Equipment Required
Calibration Allow at least 5 minutes warm-up before commencing calibration. Access to Calibration Adjustments All adjustments are on the control board, which is mounted above the main (power) board, except where stated. To gain access to the board it is necessary to remove the top cover. WARNING! Wh...
Page 14 - Set Power Limit
Voltage Calibration Connect DMM, set to Volts, across output. Set voltage controls to minimum and current control to maximum. Switch output ON and check for a reading of 00·00V ± 0·01V on display and DMM. Set voltage controls to maximum. Adjust VR16/VR116 (maximum output volts) for a reading of 35·3...
Page 15 - Sécurité
Sécurité Cet instrument est de Classe de sécurité 1 suivant la classification IEC et il a été construit pour satisfaire aux impératifs EN61010-1 (impératifs de sécurité pour le matériel électrique en vue de mesure, commande et utilisation en laboratoire). Il s'agit d'un instrument d'installation Cat...
Page 16 - Tension d’utilisation secteur; Câble secteur; Montage
Installation Tension d’utilisation secteur Vérifier que la tension opérationnelle de l'instrument indiquée sur le panneau arrière est appropriée pour l'alimentation locale. S'il s'avère nécessaire de modifier la tension opérationnelle, procéder de la manière décrite ci-dessous: 1. S'assurer que l'in...
Page 17 - Connexions; Opération; Réglage de la sortie; Tension constante
Connexions Toutes les connexions sont effectuées au panneau avant. Relier la charge aux bornes positive (rouge) et négative (noire) marquées OUTPUT (Sortie). Les bornes de sortie ont une intensité nominale de 15 A. Effectuer des connexions de télédétection à la charge, le cas échéant, des bornes de ...
Page 19 - Fusible; Nettoyage
les valeurs directement sur l’affichage de l’utilisateur. Si, pour une raison quelconque, la tension de sortie dépasse la tension de protection OVP préréglée, y compris la tension forcée de manière externe, il se produira un déclenchement de la sortie. Il se produira également un déclenchement de la...
Page 20 - Sicherheit
Sicherheit Dieses Gerät wurde nach der Sicherheitsklasse (Schutzart) I der IEC-Klassifikation und gemäß den europäischen Vorschriften EN61010-1 (Sicherheitsvorschriften für elektrische Mess-, Steuer, Regel- und Laboranlagen) entwickelt. Es handelt sich um ein Gerät der Installationskategorie II, das...
Page 21 - Netzbetriebsspannung
Installation Netzbetriebsspannung Sicherstellen, dass die auf der Geräterückwand angegebene Betriebsspannung mit der Versorgungsspannung am Ort übereinstimmt. Falls es erforderlich ist, die Betriebsspannung zu ändern, wie folgt vorgehen: 1. Sicherstellen, dass das Gerät vom Wechselstromnetz getrennt...
Page 22 - Anschlüsse; Betrieb; Konstantspannung
Anschlüsse Sämtliche Anschlüsse erfolgen von der Fronttafel aus. Der Verbraucher sollte an die mit AUSGANG (OUTPUT) markierte positive (rote) und negative (schwarze) Klemme angeschlossen werden. Die AUSGANGS-Klemmen sind für eine Stromstärke von 15 A ausgelegt. Istwert-Fernerfassungs-Anschlüsse zum ...
Page 25 - Wartung; Sicherung
Wartung Die Hersteller bzw. deren Vertretungen im Ausland bieten die Reparatur von Geräten an, bei denen eine Störung aufgetreten ist. Wenn der Eigentümer die Wartungsarbeiten selbst durchführen möchte, hat er dafür Sorge zu tragen, dass diese Arbeiten ausschließlich von entsprechend qualifiziertem ...
Page 26 - Sicurezza
Sicurezza Questo strumento appartiene alla Categoria di Sicurezza 1 secondo la classifica IEC ed è stato progettato in modo da soddisfare i criteri EN61010-1 (requisiti di Sicurezza per Apparecchiature di misura, controllo e per uso in laboratorio). E’ uno strumento di Categoria II di installazione ...
Page 27 - Installazione; Tensione d’esercizio; Montaggio
Installazione Tensione d’esercizio Controllare che la tensione d’esercizio dello strumento segnata sul pannello posteriore sia uguale a quella della rete elettrica locale. Se dovesse rendersi necessario cambiare la tensione d'esercizio, osservare il seguente procedimento: 1. Controllare che lo strum...
Page 28 - Collegamento; Funzionamento; Impostazione dell’Uscita; Tensione costante
Collegamento Tutti i collegamenti si fanno dal pannello frontale. Il carico va collegato ai morsetti positivo (rosso) e negativo (nero) contrassegnati OUTPUT (uscita). I morsetti OUTPUT (uscita) hanno una portata nominale di 15A. L’allacciamento al carico di sensori a distanza, se richiesto, va coll...
Page 29 - Collegamento in serie/parallelo con altre unità
Limite di potenza L’uscita massima a tensioni diverse è delimitata dall’inviluppo di potenza illustrato di seguito. L’inviluppo di potenza è impostato per dare 35V/5A e 12V/10A sotto tutte le condizioni di carico (ambedue le uscite sotto carico); a tensioni in uscita più basse la potenza in uscita v...
Page 31 - Manutenzione; Fusibile; Pulizia
Manutenzione I Produttori o i loro agenti all’estero faranno le riparazioni necessarie in caso di guasto. Qualora l’utente desiderasse eseguire il lavoro di manutenzione, tale lavoro deve essere fatto solo da personale qualificato e usando il manuale di servizio che può essere acquistato direttament...
Page 32 - Seguridad
Seguridad Este es un instrumento de Clase de Seguridad I según la clasificación del IEC y ha sido diseñado para cumplir con los requisitos del EN61010-1 (Requisitos de Seguridad para Equipos Eléctricos para la Medición, Control y Uso en Laboratorio). Es un instrumento de Categoría de Instalación II ...
Page 33 - Instalación; Voltaje de trabajo de alimentación; Cable de red; Montaje
Instalación Voltaje de trabajo de alimentación Verificar que el voltaje de trabajo de alimentación que figura en el panel posterior concuerde con el suministro local. Si fuese necesario cambiar la gama de voltajes de trabajo , proceda de la siguiente manera: 1. Cerciorarse de que el instrumento esté...
Page 34 - Conexiones; Funcionamiento; Ajuste de la salida; Voltaje constante; Corriente constante
Conexiones Todas las conexiones se efectuan desde el panel delantero. La carga debe conectarse a los bornes positivos (rojos) y negativos (negros) marcados OUTPUT (salida). Los bornes de OUTPUT están clasificados a 15A. Las conexiones a la carga del sensor remoto , si requeridas, se efectuan desde l...
Page 35 - Conexión en serie o en paralelo a otras unidades
La envoltura de potencia está fijada para producir 35V/5A y 12V/10A bajo toda condición de suministro (con ambas salidas cargadas); para salidas de voltaje inferiores, la potencia de salida está limitada por la corriente máxima de 10A. Al superar el límite de potencia, el indicador de estado cambiar...
Page 36 - Protección; Ventilación; Mantenimiento
Protección La protección contra sobrecarga de tensión (OVP ) es totalmente variable dentro de la gama de 10% a 110% del nivel de salida máximo de la salida. El límite de OVP se fija mediante el potenciómetro prefijado SET OVP, ajustable por destornillador, accedible por medio de un agujero en el pan...
Page 37 - Warranty Information; Warranty; How do you get service?
Warranty Information Warranty What does this warranty cover? This Limited Warranty is provided by Xantrex Technology, Inc. ("Xantrex") and covers defects in workmanship and materials in your XPF series. This warranty lasts for a Warranty Period of three years (3 years) from the date of purch...
Page 38 - What does this warranty not cover?; Product; Exclusions
What does this warranty not cover? This Limited Warranty does not cover normal wear and tear of the product or costs related to the removal, installation, or troubleshooting of the customer's electrical systems. This warranty does not apply to and Xantrex will not be responsible for any defect in or...
Page 39 - Out of Warranty Service
Return Material Authorization Policy Before returning a product directly to Xantrex you must obtain a Return Material Authorization (RMA) number and the correct factory "Ship To" address. Products must also be shipped prepaid. Product shipments will be refused and returned at your expense if...
