Xantrex SW3000 - Manual

Xantrex SW3000

Xantrex SW3000 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
Page: / 64

Table of Contents:

  • Page 4 – About This Guide; The following conventions are used in this guide.
  • Page 5 – iii; This; Related Information; NOTE; STATEMENT OF HAZARD; Contains statements of avoidance or strict compliance.
  • Page 6 – Important Safety Instructions; The Freedom SW 3000 contains no user-serviceable parts. See; ELECTRICAL SHOCK HAZARD
  • Page 7 – FIRE AND BURN HAZARD
  • Page 8 – Freedom SW 3000 Installation Guide; Precautions When Working With Batteries; Never smoke or allow a spark or flame near the engine or batteries.
  • Page 9 – vii; Precautions When Preparing to Charge; EXPOSURE TO CHEMICALS AND GASES HAZARD; Make sure the area around the battery is well ventilated.; RISK OF DAMAGE TO THE INVERTER/CHARGER; Do not place a battery on top of the inverter/charger.
  • Page 10 – Regulatory; LIMITATIONS ON USE; Do not use in ambulances or other life-saving emergency vehicles.
  • Page 11 – Contents
  • Page 15 – Introduction
  • Page 16 – Materials List
  • Page 17 – Installation Information; Before You Begin the Installation; Xanbus System Installation Guide; Installation Codes; ELECTRICAL SHOCK AND FIRE HAZARDS
  • Page 18 – About the Xanbus System; Figure 1; Typi
  • Page 19 – Xanbus Enabled; Reliable. Software control eliminates analog signalling errors.; System Accessories; . Please provide the part number of the accessory to the
  • Page 20 – Planning the Installation; Inverter/Charger Owner’s Guide; Two Key Performance Factors; Size and Length of DC Cables
  • Page 21 – Planning; Xanbus System Installation Guide.
  • Page 22 – Figure 2 does not show all required
  • Page 23 – AC Components; AC Input; The Freedom SW 3000 is designed to be connected to AC
  • Page 24 – AC Disconnect and Over-Current Protection Device; AC Input Protection; Tested GFCI Models; Manufacturer; Hubbell
  • Page 25 – Distribution Panels; Definition; AC Wire Size In and Out of the Inverter/Charger; Split phase; Gnd
  • Page 26 – The wiring; AC Output Neutral Bonding; The AC source must have its neutral conductor bonded to ground.; Bonding system; The Freedom SW 3000 provides a system that; Suitability; This automatic neutral-to-ground bonding system requires AC
  • Page 27 – DC Components; Batteries; Table 3; Re
  • Page 28 – DC Grounding
  • Page 29 – Unpacking and Inspecting the Freedom SW 3000 Inverter/Charger; To unpack and inspect:; Freedom SW 3000 Sine Wave Inverter/Charger Owner’s Guide; HEAVY LOAD; Physical Specifications” on page 40)
  • Page 30 – Installation Tools and Materials; Tools; Wire stripper; Materials; DC battery cables sized according to Table 3 on page 13
  • Page 31 – Installing the Inverter/Charger; Overview
  • Page 32 – Step 1: Choosing a Location for the Inverter/Charger; FIRE AND EXPLOSION HAZARD; Ventilated
  • Page 33 – Safe; be installed; Orientation
  • Page 34 – Considerations
  • Page 35 – Figure 3; Mounting Orientations; Desktop Mount
  • Page 36 – Wall Mount DC on Right
  • Page 37 – Step 3: Connecting the AC Input and AC Output Wires; General AC Wiring Considerations; AC and DC Wiring Separation; FIRE, ELECTRICAL SHOCK, AND ENERGY HAZARDS
  • Page 38 – Connecting AC Input Wires; To make the AC input connections:; Install a strain-relief clamp in the AC knockout.; Figure 4; AC Wiring Compartment; EQUIPMENT DAMAGE
  • Page 39 – Secure the strain-relief clamp on the AC input cable jacket.; Connecting the AC Output Wires; To make the AC output wiring connections:; Do not connect the output of the inverter to any incoming AC source.
  • Page 40 – Terminals
  • Page 41 – Step 4: Connecting the DC Cables; DC Connection Precautions; For recommended DC cables and fuse size, see Table 3 on page 13.; Preparing the Cables; To prepare the DC cables:
  • Page 42 – Guidelines for Routing the DC Cables; Follow these guidelines to ensure maximum performance.; ELECTRICAL SHOCK AND FIRE HAZARD
  • Page 43 – Connecting the DC Cables to the Inverter/Charger; To connect the DC cables:; Open the DC disconnect switch or turn off the DC circuit breaker.; FIRE HAZARD
  • Page 44 – at the inverter/charger; Figure 5; DC Cable Conne; Figure 6; DC Terminal Covers
  • Page 45 – To connect the chassis ground:; DC Wiring and DC Grounding; Chassis ground point
  • Page 46 – Mounting Options; You can mount the BTS in one of two ways:; Figure 8; BTS with Cable
  • Page 47 – Mounting to the Negative Battery Terminal; To mount the sensor on the negative battery terminal:; Wait 10 minutes for any explosive battery gases to dissipate.; Figure 9; BTS Mounted on the Negative Battery Terminal
  • Page 48 – Conne
  • Page 49 – Mounting to the Side of the Battery Case; To mount the sensor on the battery case:; Select the battery to be monitored.
  • Page 50 – Step 6: Connecting to the Network; To connect the Freedom SW 3000 to the Xanbus network:; this network is not an Ethernet system
  • Page 51 – Step 7: Performing Checks Prior to Initial Start-Up; Chassis and AC grounds are properly installed.
  • Page 52 – Step 8: Testing Your Installation; the Freedom SW 3000 works in invert mode,; Testing in Invert Mode; Freedom SW 3000 Front Panel
  • Page 53 – Testing in Charge Mode and AC Bypass Mode; To verify that the Freedom SW 3000 starts charging:; Installation Complete
  • Page 54 – Inverter/Charger Physical Specifications; For complete inverter/charger specifications, refer to the; Table 4; al Spe
  • Page 55 – Battery Information; Battery Bank Sizing; Battery capacity; Battery size or capacity is just as important as the; Estimating Battery Requirements; Calculating Battery Size; Step 2: Calculate Battery Size
  • Page 56 – If you find that the system shuts down when appliances; Table 5; Battery Sizing Example; Appliance
  • Page 57 – Battery Banks; Mixing Batteries; Batteries connected in parallel should be of the same; Battery Bank Sizing Worksheet; Restrictions on Motor Size
  • Page 58 – Battery Sizing Worksheet; Recommended Battery Bank Size in Ah (multiply by 2)
  • Page 59 – Cabling and Hook-up Configurations; Parallel Connection; Batteries Conne
  • Page 60 – Series Connection
  • Page 61 – Series-Parallel Connections; Batteries in Series-Parallel Conne
  • Page 64 – Xantrex Technology Inc.; ustomerservi
Loading the manual

TM

TM

This

g

u

id

e for

u

se by qu

alifi

ed installers only.

Freedom SW 3000
Sine Wave Inverter/Charger

Installation Guide

FREEDOM

SW

3000

In

ve

rter

R

eset Enable

Inv

er

ter

AC

/

On

Cha

rge

Fa

ult

Xanbus

In

ter

fac

e

FREEDOM

SW

3000

Inv

er

ter

R

eset Enable

Inv

erter

AC/

On

Cha

rge

Fau

lt

Xanbus I

nte

rfa

ce

Date

of Manufacture

Serial Number

CAUTION:

To reduce the risk of fire, do not

cover or obstruc

t ventilation openings. Do not mount

in a zero-clearance compartment. Overhea

ting may

result. Do not e

xpose to rain or spray.

INSTALLATION REQUIREMENTS:

Mount this inv

erter/charger only in the orientations

specified in the inst

allation g

uide provided.

WARNING:

Shock hazard. Do not open. No

user serviceable parts. Energized from both AC and
DC sources. Disconnect all

sources before servicing.

Use only ground-fault circuit interrupters (GFCI)
specified in the installation guide supplied. Other
types may fail to operate properly when connected to
this equipment. Refer to ma

nual. Charge only

lead-acid batteries. Other b

attery types may burst

causing personal injury and damage.

Nominal DC Operating Voltage:

12 Vdc

Nominal AC Output Voltage:

120 Vac , 1Ø

Nominal AC Output Frequency:

60 Hz

Max. Continuous AC Output Current:

25 A

Max. Operating DC Input Current:

320 A

Max. Continuous AC Output at Nominal DC
Input:

3000 VA at 25°C

Max. Output Surge Power (5 s duration):

6000 VA

Max. DC Input Voltage:

16 Vdc

Max. Ambient Temperature:

50°C

Inverter Mode:

Nominal AC Input Voltage:

120 Vac , 60 Hz, 1Ø

Power Factor:

> 0.95

Charging DC Output Voltage Range:

5.0 - 16.0 Vdc

Max. Continuous Battery Charger DC Current at
Nominal AC Input:

150 A

Max. AC Input Current:

30 A per line Split Phase,

30 A per line Dual

Charger Mode:

3000W SINEWA

VE INVE

RTER/CHARGER

FSW3000

815-3000

Model
Number

FGA

Number

FREEDOM SW 3000

Designed in Canada
Assembled in China

DANGER:

To reduce the risk of explosion, do not

install in an area in

which igni

tion-protected

euipment is requi

red.

UL 45

8

CS

A 107.1

-01

3033614

FREEDOM

SW

3000

FREEDOM

SW

3000

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 4 - About This Guide; The following conventions are used in this guide.

ii Freedom SW 3000 Installation Guide About This Guide Purpose The purpose of this Owner’s Guide is to provide procedures for installing the Freedom SW 3000 Inverter/Charger. Scope The Guide provides safety guidelines as well as information on installing the inverter/charger. It does not provide det...

Page 5 - iii; This; Related Information; NOTE; STATEMENT OF HAZARD; Contains statements of avoidance or strict compliance.

975-0546-01-01 iii This g u id e for u se by qu alifi ed installers only. Related Information You can find more information about Xantrex Technology Inc. as well as its products and services at www.xantrex.com . NOTE : The Installation Guide (Document Part Number: 975-0545-01-01) is primarily intend...

Page 6 - Important Safety Instructions; The Freedom SW 3000 contains no user-serviceable parts. See; ELECTRICAL SHOCK HAZARD

iv Freedom SW 3000 Installation Guide Important Safety Instructions IMPORTANT: R EAD AND SAVE THIS I NSTALLATION G UIDE FOR FUTURE REFERENCE . This chapter contains important safety and installation instructions for the Freedom SW 3000 Inverter/Charger (Freedom SW 3000). Each time, before using the ...

Other Xantrex Models

All Xantrex Other