Xantrex GT100E - Manuals

v Important Safety Instructions 1. Before installing and using the GT100E MS Combiner Box for Master/Slave Configuration, read all instructions and cautionary markings on the GT100E MS Combiner Box for Master/Slave Configuration, GT100E Grid Tie Inverter, and all appropriate sections of this manual....

152602 vii Important Safety Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - v 1 Introduction GT100E MS Combiner Box - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–2 Master/Slave Configuration - - - - - - - - - - - - - - - - - - - - ...

152602 ix Figure 1-1 Configuration Diagram - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–4 Figure 2-1 GT100E MS Componenets - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–3 Figure 2-2 Wall Mounting Bracket Locations - - - - - - - - - - - - - - - - - - - - -...

1 Introduction Chapter 1 contains a description of the GT100E MS and lists the different operating states available with the GT100E MS Combiner Box.

Introduction 1–2 152602 GT100E MS Combiner Box The GT100E MS combiner box, when installed with dual GT100E s, allows the GT100E Master/Slave configuration to maximize energy production during periods of low irradiance. A system would consist of two - 100kW inverters, one as the master and the other ...

Master/Slave Operation States 152602 1–3 If daily role reversal is on, then the configured slave is operational slave on odd days (January 1,3,5,...) and operational master on even days (January 2,4,6,...). Master Unit The GT100E Master inverter will control the GT100E MS Combiner Box via a control ...

Introduction 1–4 152602 shutdown. The Master inverter will disable the Slave inverter and close the contactor in the GT100E MS Combiner Box. The Master inverter will go online. Fault Condition If the Master or Slave Inverter gets a fault or the status signal from either inverter is lost, the inverte...

2 Installation Chapter 2 contains procedures on how to mount the GT100E MS and make the cable connections.

Installation 2–2 152602 Equipment Required • Ratchet Handle • Extension • Metric socket set • Metric wrench set • Metric hex wrench set • Torque wrench with 0-150Nm minimum range • Phillips Screwdriver Unpacking the GT100E MS To unpack the GT100E MS from the shipping pallet: 1. Remove the packing ma...

Installation 2–4 152602 Mounting Instructions To mount the MS100E combiner box onto a wall: 1. Install the 4 wall mounting brackets P/N 062-2000-02 to the rear of the MS100E Combiner box, see Figure 2-2. 2. Anchor the GT100E MS combiner box to the wall using anchor bolts. Important: The GT100E MS Co...

Cable Installation 152602 2–5 Cable Installation Wire Gauge and Torque Specifications The following torque specifications are to be used on all electrical interfaces made during installation of the GT100E MS Combiner Box. Wire Gauge Requirements for the GT100E MS Combiner Box One or multiple wires u...

Installation 2–6 152602 MS100E Connections Use the following descriptions and figures to correctly identify access panels and route wiring. Input/Output Access Panels Install all the cable strain reliefs, customer supplied, needed for cable entry in both Access Panels, see Figure 2-3. Figure 2-3 Inp...

Installation 2–10 152602 GT100E MS Control Power Cable To make GT100E MS Control Power Cable connections: 1. Connect the GT100E MS combiner box power cable assembly P/N 1- 152492-01 from the GT100E #1 through the access panel and connect it to P1, see Figure 2-7. 2. Connect the GT100E MS combiner bo...

Installation 2–14 152602 To install the MS100E Interface Assembly for GT100E #2: 1. Repeat the MS100E Interface Assembly Instructions for GT100E for the second GT100E unit - GT100E #2. GT100E Unit Installation To install the GT100E refer to the GT100E Grid Tie Inverter Installation Manual (P/N 15236...

3 Configuration Chapter 3 describes how to configure the GT100E MS for Master/Slave configuration.

Configuration 3–2 152602 Master/Slave Configuration The Master/Slave system can be configured through the Xantrex Solar GUI (Graphical User Interface) software, P/N 1-152577-01, or through the Operator Interface Panel. Establish remote or local communication with the GT100E, using the Xantrex Solar ...

152602 WA–1 Warranty and Product Information Limited Warranty 1.1 What does this warranty cover and how long does it last? This Limited Warranty is provided by Xantrex Technology Inc. ("Xantrex") and covers defects in quality in workmanship and materials ("Defects") in your GT100E MS...

Warranty and Return 152602 WA–3 1.7 Exclusion for Documentation Without limiting the generality of the foregoing, unless specifically agreed to by it in writing, Xantrex: a. makes no warranty as to the accuracy, sufficiency or suitability of any technical or other informa-tion provided in manuals or...