Xantech WPK1 - Manuals - manualsarea.com

Page 2 - WATERPADTM VERSIONS

 2 CD VOL VOL TUNER TNR TNR DISC + DISC --- OFF MUTE SAT DVD WPK1 • Two tiers of memory per button. Applies to both source select and control function buttons. • Sequence commands, including 1 to 30 second delays, can be programmed under any button (including the 2nd tier) without using up button s...

Page 3 - Controllers; INSTALLATION; Determine the client's system components and needs in detail.; before; affixing the real button Icons.; A Typical 4-Source Configuration; receiver and the associated source.; The Waterpad must have the following function commands

 3 Controllers WPK1 TAPE DVD CD CATV SAT TUNER CH GUIDE MENU MUTE OFF VOL VOL CH DISC CD VOL VOL CATV DVD VCR OFF SAT TUNER TAPE LD CH CH DISC MUTE WPK-6 This version has 14 function buttons and 6 sourcebuttons. Use this when you wish to control five orsix source components. WPK-8 This version has ...

Page 4 - All four versions of the Waterpad appear the; function; keys. When you apply; function icons; unused LEDs are covered up as in; PROGRAMMING THE WATERPAD; It cannot be; Typical 4-Source Button Assignment

 4 The next step is to determine which Waterpad version andkeypad button icons are required to perform this job, as follows: 1. Since there are 4 sources, 4 banks will be required. We will need the WPK-4 Waterpad version as shown in Fig. 1. PLEASE NOTE: All four versions of the Waterpad appear the ...

Page 5 - before applying the button icons.; dry and free of any grease or dirt.; Icon Application; WATERPADTM

 5 Controllers 8. The Waterpad is now wired into the final system (refer to Figs. 3 & 5) and all commands tested again -- before applying the button icons. 9. If the system functions correctly, the button icons can then be applied, as shown in Fig. 4. Finally, the Waterpad is mounted to the wal...

Page 6 - Cable Terminations; • Four of the seven leads are for the; do not allow the end to be; Like the Smart Pad; • See Fig. 3 for STATUS connections in a typical system.; • The Waterpad requires considerable room in the J-box.

 6 Fig. 5 Cable Terminations +12V (red) STATUS (green) COMMON (orange) RX (blue) TX (brown) Six foot 7-Conductor Cable (End of cable is not waterproof-see text). Waterproof Cable Bushing COM PORT Adapter PCB (included in Dragon Drop IR for program transfers) 8-Terminal Block TX RX COM Spare termina...

Page 7 - Mounting the Waterpad into a Retrofit type J-box.

 7 Controllers #6-32 x 5/16 PH Flat Hd Screw (4) #6-32 x 1/2 Slot White Oval Hd Screw (4) Decorator StyleCover Plate Water tight WATERPAD™ Unit (side view) Adapter Plate CAUTION: Pressure Relief Hole. See step 7 below. #4-40 x 1/4 PH Pan Hd Screw (1) and O-ring (1). Install into Relief Hole at inst...

Page 8 - Mounting the Waterpad into a New Construction type J-box.; Mounting Directly to a Wall Surface; Mounting the Waterpad directly onto a wall without a J-box.

 8 Wall Material #6-32 x 3/4 PH Flat Hd Screw (4) 3 Water tight WATERPAD™ Unit (side view) 2 #6-32 x 1/2 Slot White Oval Hd Screw (4) 1 #6-32 x 5/16 PH Flat Hd Screw (4) 8 Decorator StyleCover Plate 9 Adapter Plate CAUTION: Pressure Relief Hole. See step 7, page 8. #4-40 x 1/4 PH Pan Hd Screw (1) a...

Page 9 - TROUBLESHOOTING; SPECIFICATIONS

 9 Controllers WPK1 TROUBLESHOOTING If you encounter problems, review each of the following items and take corrective action as described. Ifproblems persist, contact Xantech Technical Support. 1. The Waterpad does not have RESTORE or CLEAR MEMORY buttons as does the SmartPad 2 or 3 . How do I perf...

Page 10 - Use these blank Waterpad panels when planning button layouts.

 10 WPK1 1-29-01Rev.D Use these blank Waterpad panels when planning button layouts.