Winegard TN-2301 - Manuals - manualsarea.com

Page 2 - diagnostic lights; can be viewed without moving the TravelNet; Warning

Ver. 1.5 4/21/2009 - 2 - TravelNet’s Cellular Router System is Preconfigured And Ready to Install with these Easy Steps Installation Instructions: ( Models TN-2301/TN-2303/TN-2305) 1. Install the TravelNet Router and Edimax Router equipment in a convenient place such as upper cabinet (Velcro works w...

Page 5 - Setup the TravelNet Data/Voice Terminal; fill out the top half of; Attention

Ver. 1.5 4/21/2009 - 5 - Setup the TravelNet Data/Voice Terminal Setting up your Carrier Account. Your TravelNet-DV requires both a data plan for internet service and a voice plan for analog phone service. Locate the “Account Application” (yellow sheet) in the “End User Envelope”. Sprint Customers (...

Page 6 - Install the; SIM Card; into the SIM card holder in the battery compartment.; Do not touch the gold-colored areas of your SIM Card.

Ver. 1.5 4/21/2009 - 6 - 1. Remove Battery Compartment Door on the bottom of the unit. Figure 7 2. Installing the AT&T SIM (Sprint and Verizon users skip to Step 3) Figure 8 Install the SIM Card into the SIM card holder in the battery compartment. • If applicable, remove the SIM Card from the la...

Page 7 - Rechargeable; into the battery; Attach Antenna cables

Ver. 1.5 4/21/2009 - 7 - 3. Install the Battery & Secure the compartment door. Install the Rechargeable Battery Pack into the battery compartment. Remove the battery compartment door, insert the battery connector into the battery terminal, arrange the battery pack in the compartment, and replace...

Page 8 - Attach power cable; Power Supply Adapter

Ver. 1.5 4/21/2009 - 8 - Connect Ethernet cable to the Ethernet port on the TravelNet Network Port (as shown) and to the Edimax WAN port (as shown) Antenna cables not shown for clarity. Figure 12 6. Attach Phone Cable Connect an RJ-11 Phone cable from a standard phone to the Phone input (J1 Figure 1...

Page 9 - Understanding the LED Lights; Note; LED Status Table

Ver. 1.5 4/21/2009 - 9 - 8. Turn on Cell Router Power using switch. Figure 14 9. Understanding the LED Lights Figure 15 Note : LED’s are tricolored, Green, Amber and Red and this corresponds to the background colors of the table below. LED Status Table LED Status Power Messaging Phone Service /SIM S...

Page 10 - Attention Installer; : Place “User Envelope” in cabinet or drawer for your

Ver. 1.5 4/21/2009 - 10 - TravelNet Data/Voice (TN-2303) Terminal Setup Activate your Sprint TravelNet Data/Voice on the Sprint Network Your TravelNet Data/Voice requires a data plan for internet and a voice plan to hook up the analog phone. Locate the “Account Application” (yellow sheet) in the “En...

Page 11 - ctek

Ver. 1.5 4/21/2009 - 11 - Figure 17 1. When all devices are connected and powered on, use your computer to connect to the TravelNet Device Manager . • Launch your Web browser (Internet Explorer or Firefox). • Go to the browser’s address bar, type http://192.168.1.1 , and press Enter or click the gre...

Page 12 - Proceed to; Set Up a Wireless WAN Data Connection; MDN

Ver. 1.5 4/21/2009 - 12 - Figure 19 • Proceed to Set Up a Wireless WAN Data Connection . TIP : Bookmark the TravelNet Device Manager access page ( http://192.168.1.1 ). 3. For Sprint Activation, manually enter your MSL/SPC Code (4a) , your MDN (10-digit wireless phone number) (4b) , and your MIN/MSI...

Page 13 - Always On; the WiFi Router, and finally laptop.

Ver. 1.5 4/21/2009 - 13 - 5. Click Setup, click Wireless WAN in the Setup menu. 6. PSD Auto Connect select Always On 7. Do a hard restart of all network devices in order, first the TravelNet Cellular Router, 2 nd the WiFi Router, and finally laptop. Activate your AT&T TravelNet Data/Voice (TN-23...

Page 14 - Rechargeable Battery Pack

Ver. 1.5 4/21/2009 - 14 - NOTE; Do not touch the gold-colored areas of your SIM Card. Figure 20 2. Install the Rechargeable Battery Pack into the battery compartment. (Fig. 20 above) • _ With the battery compartment door open, insert the battery connector into the battery terminal. • Arrange the bat...

Page 15 - can reduce static or buzzing during voice calls.; Ethernet; Refer to the Edimax users guide CD for additional information.; WEP Key Setup; WEP; Encryption Key 1: Enter your 10 Characters Key- see chart below

Ver. 1.5 4/21/2009 - 15 - • _ In a vehicle environment, grounding to the frame and battery or alternator can reduce static or buzzing during voice calls. Connect the Ethernet (RJ-45) cable to the Ethernet Port on the TravelNet D/V. (This cable will serve as the connection to your computer or WiFi Ro...

Page 16 - Parameters; Key Length; To connect your XP computer to your wireless network; Configuring the Windows XP Wireless Clients (With WEP)

Ver. 1.5 4/21/2009 - 16 - Figure 23 WEP Key Setup Parameters Default Description Key Length 64-bit You can select the WEP key length for encryption, 64-bit or 128-bit. Larger WEP key length requires 26 hexadecimal characters Key Format Use hexadecimal digits (in the "A-F", "a-f" and ...

Page 17 - To connect your Windows Vista computer to your wireless network; View and connect to available wireless networks; Applies to all editions of Windows Vista.

Ver. 1.5 4/21/2009 - 17 - Use the following procedure to configure Windows XP with SP2 for your infrastructure mode wireless network when the wireless network adapter supports Wireless Auto Configuration: 1. When the computer is within range of the wireless router or Access Point (AP) operating in y...

Page 18 - After you're connected, you can close the; Wireless Network Connection

Ver. 1.5 4/21/2009 - 18 - 1. Open Connect to a Network by clicking the Start button , and then clicking Connect to . 2. In the Show list, click Wireless . You'll see a list of the wireless networks currently available. If you do not see a network listing similar to this example: TravelNet 1234, it m...