Winegard RD-4646 - Manuals - manualsarea.com

Page 2 - Cen; FIGURE 1; INSTALLATION & ASSEMBLY

2 Cen te r Roof Line FIGURE 1 INSTALLATION & ASSEMBLY STEP 1. Choose a location for antenna that will allow it to rest in travel position with top ofreflector pointing toward rear of vehicle and to raise and rotate without interfering with otherroof-mounted equipment. Make sure inside ceiling ar...

Page 3 - FIGURE 2

3 ROOF ELEVATING SHAFT W/RW-1000 DIRECTIONAL THICKNESS LENGTH HANDLE LENGTH 4 3/4" 6 1/4" RP-4200 req. 5 3/8" 4 1/2" 6" RP-4200 req. 5" 4 1/4" 5 3/4" 6 1/4" 4 3/4" 4" 5 1/2" 6" 4 1/2" 3 3/4" 5 1/4" 5 3/4" 4 1/4" 3 1/2" 5"...

Page 4 - Cable clamp on gear housing.; FIGURE 3; Attach cable clamp here.; FIGURE 3A; INSIDE RV

4 STEP 6. Attach cable clamp to the coax cable 16" from the cable clampon the gear housing. STEP 7. Attach cable clamp to roof 3" in front of baseplate as shown in Figure 3, use 7/16" flat washer between screw head and clamp, applysealing compound over mounting screw head. STEP 8. Feed d...

Page 5 - FIGURE 4; MUST BE IN; FIGURE 8; INITIAL

5 FIGURE 4 RotationClamp ASSEMBLED VIEW CAUTION: THEANTENNA MUST BE IN THE TRAVEL POSITIONBEFORE ALIGNING THEDIRECTIONAL HANDLE,AND CEILING PLATE. Tighten screw snugly POINT TO FRONT OF RV POINTERMUST POINTTO CENTEROF ROTA-TION CLAMPWHEN INTRAVELPOSITION 1 Ceiling Plate 3 DirectionalHandle Extension...

Page 6 - STEP 2. Move rotation clamp to the LOCK position.; OPERATION; FIGURE 5; ELEVATION; NONE

6 STEP 2. Move rotation clamp to the LOCK position. STEP 3. Turn directional dial (see Figure 5) until the arrow is pointing North. STEP 4. Unsnap elevation crank and turn (clockwise) in direction of "UP" arrow, about14 - 15 turns or until some resistance is met. STEP 5. Turn receiver ON, an...

Page 7 - DO’S; on TV set to make sure it is properly adjusted.; DON’T’S; Don’t force elevating crank up or down. Check for cause of trouble.

7 TUNING ANTENNA FOR BEST PICTURE STEP 8. Your receiver should indicate it is receiving a signal. To tune yourantenna for the best picture slowly move the antenna left, then right untilyou have found the position that gives the highest signal strength. It isimportant to turn the antenna slowly; sinc...

Page 8 - MAINTENANCE; MOUNT LUBRICATION; WAVE WASHER; ELEVATING SHAFT & WORM GEAR ASSEMBLY REPLACEMENT PROCEDURE; LOWER BEARING SURFACE

8 MAINTENANCE MOUNT LUBRICATION To lubricate the mount, apply a liberal amount of silicone spray lubricant tothe elevating gear, the lubricant hole and between the gear housing andbaseplate. Run the antenna up/down and rotate the antenna to distributethe lubricant. See Figure 6. LUBRICATING RUBBER Q...

Page 9 - Signal from satellite

9 TROUBLE SHOOTING NO PICTURE 1. Check that you have a clear line of sight to the satellite (no trees,buildings, etc.). 2. Check that you have the TV set tuned for the correct channel 3 or 4(same channel as output of receiver). 3. Double check that you have entered the correct zip code into therecei...

Page 10 - PARTS LIST; REAR VIEW

10 PARTS LIST (5) E-ClipP.N. 5160818 ( 2 ) 1 / 4 - 2 0 H e x N u t ,Nylock P.N. 2160220 (4) 1/4" Flat WasherP.N. 2160039 (2) 1/4-20 X 1.75" HexBolt P.N. 2160238 46cm (18") Reflector, WhiteP.N. 2745304 (3) 1/4 x 2-5/16" PinP.N. 2160814 Bumper AssemblyP.N. 3750823 (2) 1/4-20 X 1.75"...

Page 13 - SPECIFICATIONS

13 SPECIFICATIONS ANTENNA & MOUNT Height when raised 27.25" max. Height in the travel position 12.0" max. Operating radius 17" (34" diameter circle) Roof space required 19.5" x 31" LNB Compatible with DSS ® and DISH Network TM Weight 13 lbs. max. Color White Antenna heigh...

Page 14 - ANTENNA/LIFT/LNBF TWO YEAR LIMITED WARRANTY

14 Printed in U.S.A. Winegard Company • 3000 Kirkwood Street • Burlington, Iowa 52601-2000 © Winegard Company, 2001 2451099 Rev. 6/05/01 ANTENNA/LIFT/LNBF TWO YEAR LIMITED WARRANTY Winegard Company warrants this Winegard product (excluding receiver) against any defects in materials or workmanship wi...

Page 15 - Roof Template Goes Here; TOWARD FRONT

15 Roof Template Goes Here 1-3/4" DIA.DRILL COMPLETELYTHROUGH CEILING TOWARD FRONT OF VEHICLE 1/8" DRILL BIT10 HOLES. DO NOTDRILL THROUGH CEILING. RD-4600/4646 TEMPLATE