White Rodgers 1F97W-71 - Manuals

6 connect the three pin connectors on the lowerportion of the thermostat back. Gently push untilthe snap connectors engage. DO NOT FORCEOR PRY THE THERMOSTAT, as this may dam-age the unit. PARTS OF THE THERMOSTAT The Back of The Thermostat Body Turn the thermostat body over. On the back arethe 3 ...

7 2. You may adjust the option switches for EMR,keypad lockout, and automatic changeover fromheat to cool (see OPERATING FEATURES). Other than and , the buttons are lo- cated behind the thermostat door. To open thedoor, pull the door out from the top, then swing thedoor down on its hinges. On the fo...

8 The word BATTERY flashes on the displaywhen the "AA" alkaline batteries are weak andshould be replaced. The word BATTERY isdisplayed continuously (non-flashing) whenthermostat is running on battery power only. FAN ON is displayed when the blower isoperating continuously. FAN AUTO is dis-pl...

10 Used to initiate or review thermostat program-ming. Used to select heating and cooling tempera-tures to be programmed. Used to manually override programming tohold at a selected temperature (when HOLD isdisplayed). Also used to copy one day'sprogramming into another (when COPY isdisplayed). Used ...

12 OPERATING FEATURES Now that you are familiar with the thermostatdisplay and buttons, read the following informationto learn about the many features of the thermostat. • COMPUTED ENERGY MANAGEMENT RE- COVERY (EMR) — The thermostat’s micro-computer can be set to automatically calculatethe time it w...

13 AUTOMATIC CHANGEOVER to determineproper positions of Group B option switches#1 and #2. EMR Switch Positions Switch #1 (see AUTOMATIC CHANGEOVER)Switch #2 (see AUTOMATIC CHANGEOVER)Switch #3 OFF • AUTOMATIC CHANGEOVER — If you have a heating/cooling system, you can set thethermostat to automatical...

14 (the setpoint temperature display is blank inthe AUTO mode). The system will now auto-matically switch between heating and cooling,depending on the actual room temperature. Auto Changeover Switch Positions Switch #1 ONSwitch #2 OFFSwitch #3 (see Energy Management Recovery) In the AUTO mode, the t...

15 the selected setting until you press RUN PRGM to start program operation again. This feature isideal for energy conservation when the build-ing is unoccupied for an extended period oftime. • ° F/ ° C CONVERTIBILITY — Press TIME FWD and TIME BACK at the same time until the temperature display is i...

16 press TIME BACK to decrease the cycle time. To set cooling anticipation, press SET CLOCK and ADV DAY at the same time again. The display will showCOOL 14 (factory preprogrammed cooling anticipation). Use the TIME FWD and TIME BACK but- tons to adjust anticipation. Press RUN PRGM to return to your...

17 • AUDIO PROMPTING — Each time you press a button, the thermostat will beep. • BACKLIT DISPLAY — When you press any button on the thermostat, the display is lit forapproximately eight seconds. • SYSTEM INDICATOR LIGHT — The red light on the upper right part of the thermostat indi-cates system oper...

18 Total Keypad Lockout Switch Positions Switch #1 ONSwitch #2 OFF To enable total keypad lockout, move GroupA option switch #1 to ON (see figure above).To disable total keypad lockout, move optionswitch #1 to OFF. ON 1 2 Group A Option Switches PROGRAMMING YOUR THERMOSTAT PROGRAMMING Now you are re...

19 PLANNING FOR YOUR NEEDS First, answer the following questions to help youdecide what your needs are. If you are using thethermostat for a commercial application (a store,office building, etc.), answer questions 1 through 4.If you are using the thermostat in your home,answer questions 5 through 8....

20 6a. What time does the last person leave the house in the morning? b. What temperature should the house be at this time? These will be your DAY temperaturesettings. 7a. What time does the first person arrive home in the evening? b. What temperature should the house be at this time? These will be ...

22 different time periods for each day separately(for example, heating/cooling period 1 on Mon-day may begin at 5:00 AM, but heating/coolingperiod 1 on Saturday may begin at 9:00 AM).Use the following table to plan your programtime periods, and the temperatures you wantduring each period. You may al...

23 Period 1 Period 2 Period 3 Period 4 Time Heat Temp. Cool Temp. Time Heat Temp. Cool Temp. Time Heat Temp. Cool Temp. Time Heat Temp. Cool Temp. Monday Tuesday Wednesday Thursday Friday Saturday Sunday Heating/Cooling Schedule Plan THIS THERMOSTAT ALLOWS ONE SET OF TIMES FOR BOTH HEATING AND COOLI...

25 3. Press SET CLOCK once. The display window will show the hour only. EXAMPLE: 4. Press and hold either TIME FWD or TIME BACK until you reach the correct hour and AM/PM designa-tion (AM begins at midnight; PM begins atnoon). 5. Press SET CLOCK once. The display will show the day of the week as an ...

29 Program Cooling Temperatures If outside temperature is below 50 ° F, we recommend that you remove the thermo-stat from the wall before proceeding withthe following steps to program coolingtemperatures. Personal injury and/or prop-erty damage could result from air condi-tioner compressor slugging....

30 continuously during this period, press FAN ON – AUTO until PRG FAN is displayed. 5. Repeat step 4 for Monday's heating coolingperiods 3 and 4. 6. Use the HOLD COPY button, or press ADV DAY to choose other days to program. Remember, once youenter Monday's program, Monday's programis automatically ...

31 3. Press HOLD COPY once. COPY will appear on the display. A number from 1 to 7 will also bedisplayed, representing the day you have se-lected to copy from (Monday is 1, Tuesday is2, etc.). For example, if in step 2 you selectedto copy Wednesday's program, when you press HOLD COPY , COPY 3 will be...

33 1. How can I permanently change a part of myprogram? Press VIEW PRGM and ADV DAY until you reach the time/temperature schedule you want. Then press TIME FWD or TIME BACK and and to change the program. See PROGRAMMINGYOUR THERMOSTAT. 2. How can I have no change in temperaturefrom one time period t...

35 During periods of low humidity (especiallyduring cold weather), you may feel or see aspark discharge when you touch the thermo-stat. This may cause the program to be lost orthe thermostat to display incorrectly. To cor-rect this, remove the thermostat from the walland disconnect the battery. Wait...

36 9. The display is flashing BATTERY. Whatdoes this mean?The "AA" batteries installed in the thermostatare low and should be replaced with fresh "AA"Energizer ® alkaline batteries. See OPERAT- ING YOUR THERMOSTAT. 10. The thermostat beeps every few minutes. What does this mean?The t...

37 If the outside temperature is below 50 ° F, DO NOT use the button to move the temperature below the setpoint tempera-ture. Property damage may result due tocompressor slugging. 13. Why doesn’t the temperature change at the time I programmed?There may be a number of causes for thissituation. The f...

38 • The blower delay feature is operating. Thisenergy saving feature continues to blowconditioned air through the ducts after thesystem has turned off, rather than lettingthe air dissipate. 15. Why is the system turning on and off so frequently (seldom)?The anticipation setting is too low (high). T...

39 18. Do I have to reprogram my thermostat after I change the batteries?When the thermostat is on the wall and thesystem has power, the thermostat is beingpowered by a 24v AC source. If power is lost,or if the thermostat is removed from the wall,the program will be retained for approximatelyone min...