Wayne Dalton 9100/9400/9600 - Manuals

Page 2 - Parts Breakdown

2 Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com A. FLAg ANgLES (AS REquIRED): A1. Fully Adjustable (F...

Page 3 - Important Safety Instructions; WARNINg; Tools Required

Important Safety Instructions Definition of key words used in this manual: WARNINg WARNINg INDICATES A POTENTIALLy HAzARDOuS SITuATION WHICH; IF NOT AvOIDED, COuLD RESuLT IN SEvERE OR FATAL INJuRy. CAuTION: PROPERTY DAMAGE OR INJURY CAN RESULT FROM FAILURE TO FOLLOW INSTRUCTIONS. IMPORTANT: REQUIRED...

Page 4 - Door Section Identification; Removing an Existing Door; A POWERFuL SPRINg RELEASINg ITS ENERgy SuDDENLy CAN CAuSE SEvERE; Preparing the Opening

5/16” x 1 5/8” Hex head lag screws (as required) 1/4”-20 x 11/16” Self drilling screws (as required) 1/4”-14 x 5/8” Self tapping screws (as required) (2) #12 x 1/2” Phillips head screws (2) 5/16”-18 x 3/4” Carriage bolts 1/4”-20 x 9/16” Track bolts (as required) 3/8”- 16 Hex nuts (As Required) 1/4”-...

Page 6 - InstallatIon; quick Install Flag Angles; Fully Adjustable Jamb Brackets

InstallatIon Before installing your door, be certain that you have read and followed all of the instruc- tions covered in the pre-installation section of this manual. Failure to do so may result in an improperly installed door. NOTE: Reference TDS 160 for general garage door terminology at www.dasma...

Page 7 - Cable Drum Assemblies and Track Rollers; FAILuRE TO ENSuRE TIgHT FIT OF CABLE LOOP OvER MILFORD PIN COuLD; Bottom Section

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com If a top jamb bracket was included, secure it to vertic...

Page 8 - Top Fixtures; Drawbar Operator Bracket

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com section until it is seated against bottom section. Alig...

Page 9 - Top Section; Adjusting Top Fixtures; Rear Back Hangs

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com Top Section Tools: Hammer, Step ladder, Tape measure 14...

Page 10 - kEEP HORIzONTAL TRACk PARALLEL AND WITHIN 3/4” TO 7/8” MAxIMuM; Attaching Front Cable Lift Sheaves

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com WARNINg WARNINg kEEP HORIzONTAL TRACk PARALLEL AND WITH...

Page 11 - Attaching Extension Springs; Attaching Spring Sheaves; FAILuRE TO CLOSE “S” HOOkS AND EyE BOLTS CAN RESuLT IN SEvER OR

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com Attaching Extension Springs Tools: 3/8” Wrench 20 Posit...

Page 12 - Cable Adjustments; Final Adjustments

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com Counterbalance lift cable 3 Hole clip Front cable lift ...

Page 13 - Door Arm Hookup; Trolley Arm Configuration; Inside Lock; optional Installation

Door Arm Hookup Tools: Needle nose pliers Align hole in the door arm with holes in drawbar operator bracket tabs, as shown. Insert 5/16” x 1-1/4” clevis pin, making sure hole in clevis pin is outside of second tab of drawbar operator bracket. Insert hairpin cotter into clevis pin hole and spread hai...

Page 14 - Pull Down Rope; DO NOT INSTALL PuLL DOWN ROPE ON DOORS WITH OPERATORS. CHILDREN; Step Plate

Second section 1/8” Inside lock End cap (4) 1/4”-20 x 11/16” Self drilling screws Square hole in vertical track Pull Down Rope Tools: Power drill, 1/8” Drill bit, Tape measure WARNINg WARNINg DO NOT INSTALL PuLL DOWN ROPE ON DOORS WITH OPERATORS. CHILDREN MAy BECOME ENTANgLED IN THE ROPE CAuSINg SEv...

Page 15 - Maintenance

Cleaning Your Garage Door IMPORTANT: DO NOT USE A PRESSURE WASHER ON YOUR GARAGE DOOR! While factory-applied finishes on garage doors are durable, it is desirable to clean them on a routine basis. Some discoloration of the finish may occur when a door has been exposed to dirt-laden atmosphere for a ...

Page 16 - Lifetime Limited Warranty; for as long as you own the door; TWO; uNDERSCORED BOLD FACE TyPE; warranty

Lifetime Limited Warranty Models 9100, 9400, 9600 Subject to the terms and conditions contained in this Lifetime Limited Warranty, Wayne-Dalton, A Division Of Overhead Door Corporation (“Manufacturer”) war- rants the sections of the door, which is described at the top of this page, for as long as yo...

Page 18 - Please Do Not Return This Product To The Store; thank you for your purchase.; Find a Dealer; section online at

after InstallatIon Is coMPlete, fasten thIs Manual near the garage door. Please Do Not Return This Product To The Store thank you for your purchase. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the Find a ...