Wayne Dalton 9100/9400/9600 - Manual
Wayne Dalton 9100/9400/9600 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Parts Breakdown
- Page 3 – Important Safety Instructions; WARNINg; Tools Required
- Page 4 – Door Section Identification; Removing an Existing Door; A POWERFuL SPRINg RELEASINg ITS ENERgy SuDDENLy CAN CAuSE SEvERE; Preparing the Opening
- Page 6 – InstallatIon; quick Install Flag Angles; Fully Adjustable Jamb Brackets
- Page 7 – Cable Drum Assemblies and Track Rollers; FAILuRE TO ENSuRE TIgHT FIT OF CABLE LOOP OvER MILFORD PIN COuLD; Bottom Section
- Page 8 – Top Fixtures; Drawbar Operator Bracket
- Page 9 – Top Section; Adjusting Top Fixtures; Rear Back Hangs
- Page 10 – kEEP HORIzONTAL TRACk PARALLEL AND WITHIN 3/4” TO 7/8” MAxIMuM; Attaching Front Cable Lift Sheaves
- Page 11 – Attaching Extension Springs; Attaching Spring Sheaves; FAILuRE TO CLOSE “S” HOOkS AND EyE BOLTS CAN RESuLT IN SEvER OR
- Page 12 – Cable Adjustments; Final Adjustments
- Page 13 – Door Arm Hookup; Trolley Arm Configuration; Inside Lock; optional Installation
- Page 14 – Pull Down Rope; DO NOT INSTALL PuLL DOWN ROPE ON DOORS WITH OPERATORS. CHILDREN; Step Plate
- Page 15 – Maintenance
- Page 16 – Lifetime Limited Warranty; for as long as you own the door; TWO; uNDERSCORED BOLD FACE TyPE; warranty
- Page 18 – Please Do Not Return This Product To The Store; thank you for your purchase.; Find a Dealer; section online at
GARAGE DOORS & OPENERS
Part No.
IMPORTANT NOTICES!
Wayne-Dalton highly recommends that you read and fully under-
stand the Installation Instructions and Owner’s Manual before you
attempt this installation.
To avoid possible injury, read the enclosed instructions carefully
before installing and operating the garage door. Pay close attention
to all warnings and notes. After installation is complete, fasten this
manual near garage door for easy reference.
The complete Installation Instructions and Owner’s Manual are
available at no charge from:
Wayne-Dalton, a Division Of Overhead Door Corporation,
P.O. Box 67, Mt. Hope, OH., 44660,
Or Online At
www.Wayne-Dalton.com
S
tandard
L
ift
MH
inStaLLation
inStructionS
and
owner
’
S
ManuaL
e
x t e n S i o n
9100/9400/9600
T a b l e O f C o n t e n t s
346447
REV5_03/01/2012
©Copyright 2012 Wayne-Dalton, a Division Of Overhead Door Corporation
Parts Breakdown
2
Pre-Installation
3
Important Safety Instructions
3
Tools Required
3
Package Contents
3
Door Section Identification
4
Removing an Existing Door
4
Preparing the Opening
4
Installation
6
Optional Installation
13
Door Arm Hookup
13
Trolley Arm Configuration
13
Inside Lock
13
Pull Down Rope
14
Step Plate
14
Maintenance
15
Cleaning Your Garage Door
15
Painting Your Garage Door
15
Operation and Maintenance
15
Warranty
16
Dealer Locator Information
18
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com A. FLAg ANgLES (AS REquIRED): A1. Fully Adjustable (F...
Important Safety Instructions Definition of key words used in this manual: WARNINg WARNINg INDICATES A POTENTIALLy HAzARDOuS SITuATION WHICH; IF NOT AvOIDED, COuLD RESuLT IN SEvERE OR FATAL INJuRy. CAuTION: PROPERTY DAMAGE OR INJURY CAN RESULT FROM FAILURE TO FOLLOW INSTRUCTIONS. IMPORTANT: REQUIRED...
5/16” x 1 5/8” Hex head lag screws (as required) 1/4”-20 x 11/16” Self drilling screws (as required) 1/4”-14 x 5/8” Self tapping screws (as required) (2) #12 x 1/2” Phillips head screws (2) 5/16”-18 x 3/4” Carriage bolts 1/4”-20 x 9/16” Track bolts (as required) 3/8”- 16 Hex nuts (As Required) 1/4”-...
