Wagner 9150 - Manuals

Wagner 9150 – Manual in PDF format online.

Manuals:

Manual

Manual Wagner 9150

Summary

Page 2 - English; Important Safety Information; • Read all safety information before

2 English Important Safety Information • Read all safety information before operating the equipment. Save these instructions HAZARD: INJECTION INJURY A high pressure paint stream produced by thisequipment can pierce the skin and underlying tissues,leading to serious injury and possible amputation.SE...

Page 3 - Important Electrical Information; NOTICE; Grounding Instructions; If you experience problems with your; WARNING

3 English HAZARD: GENERAL Can cause severe injury or property damage. PREVENTION: • Read all instructions and safety precautions before operating equipment. • Follow all appropriate local, state, and national codes governing ventilation, fire prevention, and operation. • The United States Government...

Page 4 - Components and Description; Controls and Functions

4 English Components and Description ON/OFF Switch . . . . . . . . . . . The ON/OFF switch turns the power to the sprayer on and off (O=OFF, l=ON). Suction tube . . . . . . . . . . . . . Fluid is drawn through the suction tube into the pump. Fluid Section . . . . . . . . . . . . A piston in the flui...

Page 5 - Important

5 English Components and Description 9146, 9150 9170 9190 GX-07GX-07 GX-08 415517 517 517519 521 Yellow (fine) 9140S GX-05 415 415 Yellow (fine) White (medium) White (medium) 25 feet 25 feet 50 feet 50 feet This pump is available in two models: a stand model (9140S) and cart models (9146, 9150 shown...

Page 6 - Assembly; Tools needed for assembly:

Do not plug in the sprayer until setup is complete. 6 English Assembly WARNING • Two adjustable wrenches • 3/16” Allen wrench Tools needed for assembly: If you have one of the cart models (9146, 9150, 9170 or 9190), follow these assembly instructions. If you have the model9140S sprayer, skip to item...

Page 7 - Locking the Spray Gun:; Model GX-08 Spray Gun; Plugging in the Sprayer:; Pressure Relief Procedure:

7 English Before you begin - This section contains instructions that will be repeatedthroughout this manual. Always lock the trigger off when attaching the spray tip or when the spray gun is not in use. WARNING Locking the Spray Gun: Model GX-05 and GX-07 Spray Gun The gun is locked when the trigger...

Page 8 - Purging and Priming the Sprayer

8 English Purging and Priming the Sprayer All new units are performance-tested at the factory and are shipped with test fluid in the fluid section to preventcorrosion during shipment and storage. If you have already used your pump, some water or solvent used in cleaningmay remain in the fluid sectio...

Page 9 - Purging and Priming the Spray Hose

O S P R A Y P R IM E 9 English Purging and Priming the Spray Hose 1. Unlock the spray gun and turn the PRIME/SPRAY knob to PRIME. 2. PULL the trigger and aim the spray gun at the side wall of a waste container. If using oil-based materials, the spray gun must be grounded while purging (seewarning be...

Page 10 - Practice / Spraying Technique

10 English Good spray pattern Paint tailing pattern (pressure too low, clogged tip) 1. Switch the pump ON (l) . Turn the PRIME/SPRAY knob to SPRAY. Turn the pressure control dial to maximumpressure (+). The spray hose should stiffen as paintbegins to flow through it. 2. When motor shuts off, unlock ...

Page 11 - Spraying Troubleshooting -; Unclogging the Spray Tip

11 English Spraying Troubleshooting - Unclogging the Spray Tip Do not attempt to unclog or clean the tip with your finger. WARNING NOTE - Do not use a needle or other sharp pointed instrument to clean the tip. The hard tungsten carbide can chip. If the spray pattern becomes distorted or stops comple...

Page 12 - Cleaning the Spray Gun Filter; Spray gun model; Cleaning the Inlet Filter

12 English Spraying Troubleshooting - Cleaning the Spray Gun Filter The filter must be cleaned every time you use your sprayer. When using thicker spray materials, the filter might need tobe cleaned more often. 1. Perform Pressure Relief Procedure, page 7. 2a. Model GX-07 - Unscrew the fitting from ...

Page 13 - Important Cleaning Notes!; Latex materials

13 English Call 1-800-880-0993 if you have any problems or questions regarding the cleaning of your sprayer. • When using latex materials, clean your sprayer and components with water. When using oil-based materials,use mineral spirits. • Do not use mineral spirits on latex materials, or the mixture...

Page 16 - Cleaning the Suction Set

16 English 1. Lock the gun and turn the pump OFF (O) . 3. When suction set is clean, thread the suction tube back into the inlet valve, and replace the return tube onto thereturn tube fitting. Replace clip. 4. Submerge the suction set into a bucket of NEW cleaning solution. 5. Turn the PRIME/SPRAY k...

Page 17 - Cleaning the Spray Gun Components

17 English 1. Make sure the pump is switched OFF (O). Make sure the PRIME/SPRAY knob is turned to PRIME. Unplug thesprayer. 2. Remove spray gun from the paint hose using adjustable wrenches. (b) (c) (a) 3. Remove filter from spray gun (refer to Cleaning the Spray Gun Filter, page 12). 4. Remove spra...

Page 18 - Shutdown; Startup

18 English Follow these steps when using latex materials only. If using materials that are oil-based, follow the Cleanup - Oil-basedmaterials and Long-Term Storage steps. Shutdown 1. Lock the spray gun off. GX-08 GX-07 GX-05 2. Turn the PRIME/SPRAY knob to PRIME. Switch the pump OFF (O) . Unplug the...

Page 19 - Separating oil

19 English 1. Fill a cup or other container with separating oil (approximately 2 ounces) supplied with the unit andsubmerge the inlet valve into the oil. Light household oilcan be substituted. 2. Place a rag over the spray hose port, and turn the switch ON (l) . When the oil has been sucked from the...

Page 20 - Cleaning the Inlet Valve

20 English (a) 1. Remove the suction set. 2. Unscrew the inlet valve assembly (a) from the sprayer. Visually inspect the inside and outside of the inlet valveassembly. Clean any paint residue with the appropriatecleaning solution. Cleaning or servicing the inlet valve may be required if the unit has...

Page 21 - Fluid Section Seal Replacement Instructions; Disassembly of the Fluid Section

21 English Fluid Section Seal Replacement Instructions Always wear protective eye wear while servicing the pump. Be sure to follow the Pressure Relief Procedure (page 7) when shutting the unit down for any purpose, including servicing or adjusting. After performing the Pressure Relief Procedure, be ...

Page 22 - Troubleshooting / Maintenance; Problem; Daily Maintenance

22 English Troubleshooting / Maintenance Problem A. The sprayer does not start. B. The sprayer starts but does not draw in paint when thePRIME/SPRAY knob is set toPRIME. C. The sprayer draws up paint but the pressure drops whenthe gun is triggered. D. The PRIME/SPRAY valve is on SPRAY and there is f...

Page 23 - Parts List • Liste de pièces • Lista de piezas

67 English Français Español Parts List • Liste de pièces • Lista de piezas Model GX-05 spray gun Item Part # Description Quantity 1 0501011 Guard Assembly ...................................1 2 0501415 Tip, 415 .................................................1 3 0516115 Complete gun assembly .........

Page 24 - Model GX-08 spray gun; Modèle du pistolet GX-08; Modelo de pistola GX-08

68 English Français Español Parts List • Liste de pièces • Lista de piezas Model GX-08 spray gun Item Part # Description Quantity 1 0501517 Tip, 517 ......................................................1 2 0501011 Guard assembly.........................................1 3 0296261 Diffuser, 7/8"...

Page 25 - Suction set; Dispositif d’aspiration; Juego de succión

69 English Français Español Parts List • Liste de pièces • Lista de piezas Suction set Item Part # Description Quantity 1 0516219 Suction set (9140S) ..............................1 0516218 Suction set (all cart models) .................1 2 0512371 Return tube (9140S) .............................1 ...

Page 27 - Accessories • Accessoires • Accesorios

71 English Français Español Accessories • Accessoires • Accesorios Part # Description 0516913 Separating Oil 0154830 Hose, Whip End, 5’ x 3/16” 0270192 Hose, Wireless, 25’ x 1/4" 0291000 Hose, Wireless, 50’ x 1/4" 0279667 Hose Connector, 1/4” x 1/4” 0088154 Pressure Gauge 0508910 Tip Extensi...

Page 28 - Warranty • Garantié • Garantia; Wagner Spray Tech

72 English Français Español Warranty • Garantié • Garantia GARANTIE LIMITÉE MATÉRIEL DE PULVÉRISATION DE PEINTURE SANS AIR Ce produit, fabriqué par Wagner Spray Tech Corporation (Wagner), est garanti, au bénéfice de l’acheteur au détail d’origine, contre tout vice de matières et toute malfaçonpour u...