Page 2 - CAUTION; WARNING
Table of Contents Safety Precautions .................................................................2 Français ..............................................................................18Español ...............................................................................20 General Descripti...
Page 3 - Gasoline Engine Safety
GAS ENGINE (WHERE APPLICABLE) Always place pump outside of structure in fresh air. Keep allsolvents away from the engine exhaust. Never fill fuel tankwith a running or hot engine. Hot surface can ignite spilledfuel. Always attach ground wire from pump unit to a groundedobject, such as a metal water ...
Page 4 - Setup
General Description This airless line striper is a precision power tool used to spraymany types of material for many types of applications includingparking lots, curbs, and athletic fields. Read and follow thisinstruction manual carefully for proper operating instructions,maintenance, and safety inf...
Page 5 - Preparing to Paint
Adjusting the Trigger Tension Use the following procedure to adjust the spring tension of thetrigger lever on the gun holder assembly. The trigger leverpulls and releases the spray gun trigger when operated fromthe trigger on the cart. The proper tension ensures that thegun will shut off when the gu...
Page 6 - Painting; Operating the Front Caster
Ground the gun by holding it against theedge of the metal container while flushing.Failure to do so may lead to a staticelectric discharge, which may cause a fire. 16. Trigger the gun into the metal waste container until the old solvent is gone and fresh solvent is coming out of the gun. 17. Lock th...
Page 7 - Cleanup; Cleaning the Spray Tip; Maintenance; General Repair and Service Notes
3. Turn off the engine by moving the engine ON/OFF switch to the OFF position. 4. Turn the pressure control knob counterclockwise to its lowest setting. 5. Unlock the gun by turning the gun trigger lock to the unlocked position. 4. Hold the metal part of the gun firmly to the side of a metal contain...
Page 8 - Maintaining the Engine; Important Facts Concerning this Sprayer; Replacing the Filter
2. Test your repair before regular operation of the sprayer to be sure that the problem is corrected. If the sprayer doesnot operate properly, review the repair procedure todetermine if everything was done correctly. Refer to theTroubleshooting section to help identify other possibleproblems. 3. Mak...
Page 9 - Replacing the Potentiometer; Replacing the Pump ON/OFF Switch
Replacing the Potentiometer Electrostatic discharge (ESD) potential could causedamage to electronic pressure control. Use SprayTECHESD wrist strap P/N 0507958 or equivalent when workingon electronic pressure control. 1. Perform the Pressure Relief Procedure.2. Pry off the pressure control knob cap t...
Page 10 - Replacing the Transducer
Replacing the Transducer Electrostatic discharge (ESD) potential could causedamage to electronic pressure control. Use SprayTECHESD wrist strap P/N 0507958 or equivalent when workingon electronic pressure control. 1. Perform the Pressure Relief Procedure.2. Using a Phillips screwdriver, removethe fo...
Page 12 - Replacing the Gears; Servicing the Clutch Assembly
Replacing the Gears 1. Perform the Pressure Relief Procedure.2. Using a Phillips screwdriver, remove the four front cover screws. Remove the front cover.. 3. Using a 7/8” open-end wrench, loosen and remove the fluid hose from the fitting on the back of the fluid section. 4. Locate the four socket sc...
Page 14 - Checking the Clutch Gap; Servicing the Fluid Section
7. Thread one of the set screws into its hole. Using an 1/8” hex wrench, rotate the screw slowly until it contacts theclutch field. Do not tighten the set screw . The tip of the set screw should mate with the drill point hole in the field.Check the clutch field for rotation. If it rotates within its...
Page 16 - Solution; Cause; Troubleshooting; Problem
Troubleshooting 16 © SprayTECH. All rights reserved. Solution 1. Turn the pressure control knob clockwise to supply power to the unit and increase thepressure setting. 2. Inspect or take to a SprayTECH authorized service center. 3. Fill the gas tank.4. Check oil level, fill if necessary. 1. Rotate t...
Page 18 - Consignes de sécurité; AVERTISSEMENT; ATTENTION; Français
18 © SprayTECH. Tous droits réservés. Consignes de sécurité Le présent manuel comprend des renseignements devant êtrelus attentivement avant toute utilisation de l'appareil. Lorsquel'un des symboles suivants apparaît, il est recommandé d'êtreparticulièrement attentif et de tenir compte des mesures d...
Page 19 - Sécurité des moteurs à essence
© SprayTECH. Tous droits réservés. 19 MOTEUR À ESSENCE (DANS LES CAS OÙ CELA S’APPLIQUE) Toujours placer la pompe à l’extérieur de la structure à l’airfrais. Garder tous les solvants loin de l’échappement dumoteur. Ne jamais remplir le réservoir à carburant lorsque lemoteur est en marche ou lorsqu’i...
Page 20 - Precauciones de seguridad; ADVERTENCIA; PRECAUCION; Español
20 © SprayTECH. Todos los derechos reservados. Precauciones de seguridad Este manual contiene información que debe leer y comprenderantes de usar el equipo. Cuando se encuentre con uno de lossiguientes símbolos, asegúrese de observar sus indicacionesde seguridad. Este símbolo indica la existencia de...
Page 21 - Seguridad del motor de gasolina
© SprayTECH. Todos los derechos reservados. 21 PELIGRO: PELIGRO DE EXPLOSIÓN DEBIDO A MATERIALES INCOMPATIBLES - Podríacausar lesiones severas o daños en lapropiedad. PARA PREVENIR: • No utilice materiales que contengan blanqueador o cloro.• No use solventes con hidrocarburos halogenados, tales como...
Page 22 - Parts List; Main Assembly
22 © SprayTECH. All rights reserved. Parts List Main Assembly 1 2 3 7 9 15 12 17 14 13 16 8 2 10 11 456 8 2 18 19 20 22 23 27 28 29 24 26 25 21 Item Part # Description Quantity 1 0509658 Pump mounting plate..................................1 2 0509293 Lock nut ..........................................
Page 23 - Drive Assembly
© SprayTECH. All rights reserved. 23 Item Part # Description Quantity 1 9850936 ON/OFF switch ...........................................1 2 0509558 Electronic pressure control assembly .........1 3 0509556 Screw ..........................................................4 4 0507973 Potentiometer ......
Page 26 - Electrical Schematic
26 © SprayTECH. All rights reserved. Fluid Section Assembly (P/N 0509133) 1 2 3 4 6 9 12 1314 15 7 8 19 16 17 18 20 21 22 10 5 11 23 Install lower packing with large beveled edge facing up. Install upper packing with large beveled edge facing down. Large Beveled Edge Large Beveled Edge Item Part # D...
Page 27 - Filter Assembly
© SprayTECH. All rights reserved. 27 Filter Assembly Item Part # Description Quantity 1 0294194 Filter body ...................................................1 2 14069 Filter, 50 mesh ............................................1 3 9894245 Core spring ..................................................
Page 28 - Labels
28 © SprayTECH. All rights reserved. Return Hose Assembly (P/N 0509173) Item Part # Description Quantity 1 0509746 Hose assembly .........................................1 2 0509764 Tube .........................................................1 Labels Part # Description 0509824 Logo label, front 05...
Page 29 - Notes
Page 32 - Limited Warranty; Commercial Airless Spray Equipment
32 © SprayTECH. All rights reserved. Limited Warranty Commercial Airless Spray Equipment Two Year Warranty SprayTECH, a division of Wagner Spray Tech Corporation ("SprayTECH"), warrants this product against defects in material andworkmanship for a period of two years following the date of pu...
