Wagner 770 - Manuals

l O Start Important Safety Warning Be careful when handling the spray gun so you don’t accidently spray yourself. The high pressure paint stream could pierce your skin causing serious injury. If an accident happens see detail procedures in the Safety Information section on pages 4-5. See physician i...

l O l O ON OFF HOPPER LID Start 1. Load Material What you’ll need • The material you plan to spray • Extension cord • Waste container 2. Push tab on filter twice to test inlet valve operation 3. Fill hopper TIP: If material is old, strain when pouring into hopper to help prevent clogging when sprayi...

SQUEEZE l O ON L OC K What you’ll need • Scrap material/cardboard • Drop cloths to protect floors and furnishings from overspray Special Note Don’t let the hopper run empty. If the hopper runs empty go to page 8 “Load Material” and page 9 “Get- ting Material to Flow “ and follow the steps as shown 2...

GOOD JOB! Hold the Spray Gun Level BAD Start 3. Practice Spraying What you’ll need • Scrap material/cardboard GOOD JOB! Practice on a piece of scrap material/cardboard Tip: Trigger gun after starting the stroke. Release the trigger before ending the stroke. The spray gun should be mov-ing when the t...

Start stroke End stroke Pull trigger Release trigger Move steadily ! GOOD JOB! BAD Spray Technique Spray Pattern GOOD SPRAY PATTERN BAD SPRAY PATTERN: TAILING GOOD JOB! Overlap Your Strokes See page 12 Using the Wagner Paint Crew Using the Wagner Paint Crew • Practice Spraying English 11

If material isn’t flowing properly after clearing these things see additional instructions in the Fix Spraying Problems section Page 22 Common Solutions to Spraying Issues Keep material flowing smoothly while spraying Straining material when loading hopper helps minimize clogging If experiencing iss...

L O C K l O 3 Note: If spray tip is difficult to rotate relieve pressure by turning PRIME/SPRAY knob to PRIME and squeeze trigger while pointing at scrap material/cardboard. Release trigger and try rotating spray tip again l O ON U NL O C K 1 Start 1 Clear the Spray Tip 2. Release trigger and lock s...

HANDLE HANDLE Start IMPORTANT: Never clean filter by poking with sharp object . Perform Pressure Relief Procedure Page 7 4. Remove inlet filter from hopper 3. Empty material from hopper into original material container 7. To resume painting follow: Load Material and Get Material to Flow instructions...

Start 1 Clean the Spray Gun Filter What you’ll need • Wrench • Warm, soapy water for latex material • Mineral spirits for oil based materials • Replacement spray gun filter (if necessary) 5. Remove filter from housing 9. Reassemble spray gun 8. Replace cleaned filter, tapered end first, into gun hou...

HOPPER LID 5. If your break is more than an hour slowly pour ½ cup of water of paint in hopper. This helps prevent paint from drying and causing possible clogs 6. Place lid on hopper and keep sprayer out of sun Instructions are for latex material only Note: If using oil based material follow instruc...

4. Steps for Getting Material to Flow ( page 9 ) 3. If water was added during shut down stir water into material 2. Remove spray gun from plastic bag or from bucket of water Startup from Short Term Storage What you’ll need • Stir stick Start 4 3 2 Page 9 1 OR English 17 Cleanup and Storage • Startup...

l O SQUEEZE T U R N ON HANDLE HANDLE l O OFF Flush Material From Sprayer 12. Turn knob to PRIME and squeeze trigger until pressure is relieved. Release trigger, lock spray gun, turn power OFF 11. Continue squeezing trigger until fluid is coming out clear. Repeat as necessary 8. Squeeze trigger 9. Tu...

l O l O ON OFF 2-3 MINUTES 3. Remove inlet filter and clean with appropriate cleaning solution. Replace inlet filter in hopper 9. Hold material return tube over a waste container. Run for 2 to 3 minutes 10. Turn power OFF 7. Turn knob to PRIME 8. Turn power ON 4. Partially fill hopper with NEW clean...

HOUSEHOLD OIL HOUSEHOLD OIL Start Clean Spray Gun Components What you’ll need • Soft bristled brush • Light household oil • Warm, soapy water if using latex material • Mineral spirits for oil based material • Wrench 4. Remove filter from spray gun 7. Install gun filter tapered-end first. Reassemble ...

l O ON OFF 5 SECONDS HOUSEHOLD OIL HOUSEHOLD OIL l O Start 1 Long Term Storage 2. Remove inlet filter 4. Cover outlet valve with a rag. Turn power ON . Let run for 5 seconds 5. Turn power OFF 7. Wipe entire unit, hose and spray gun with damp cloth to remove accumulated material INLET FILTER Start Wh...

Before servicing, always release system pressure by following Pressure Relief Procedure (page 7). Problem A: The sprayer does not start Cause Solution 1. Sprayer is not plugged in Plug sprayer in 2. ON/OFF switch is set to OFF Turn ON/OFF switch to ON 3. The sprayer shuts off while under pressure Mo...

Inlet fitting O-ringInlet fitting O-ring Inlet fitting O-ring Inlet fitting Inlet valveInlet valve O-ring 2. Remove inlet filter from bottom of hopper 4. Inspect the three inlet fitting O-rings and replace if worn. If not replacing O-rings do not remove them but clean with appropriate cleaning solut...

Español 74 Français 74 English 74 4 8 5 1 3 2 7 6 6 1 2 3 4 5 6 9 Spray Gun • Pistolet • Pistola Sprayer • Pulvérisateur • Rociador Item Article Articulo Part No. No de piéce Pieza No. English - Description Français - Description Español - Descripción Quantity Quantite Cantidad 1 0515223 Hopper lid ...

Warranty • Garantie • Garantía Español 75 Français English Limited WarrantyAIRLESS PAINT SPRAY EQUIPMENT This product, manufactured by Wagner Spray Tech Corporation (Wagner), is warranted to the original retail purchaser against defects in material and workmanship for one year from date of purchase....