Viking VGR73626BPG - Manuals

6 Dimensions / Specifications - 36”/48” Rangetop 35-7/8” (91.1 cm) 47-7/8” (121.6 cm) 8” (20.3 cm) 27-3/4” (70.5 cm) 2-1/4” (5.7 cm) 30” (76.2 cm) Note: Unit shown with standard island trim. Minimum clearances from adjacent combustible construction • Cooking surface and below, i.e., 36” (91.4 cm) an...

8 Minimum clearances from adjacent combustible construction: Below cooking surface (36” [91.4 cm] and below) • Sides - 0” • Top grate support - 36” (91.4 cm) Above cooking surface (above 36” [91.4 cm]) • Sides - 12” (30.5 cm)• Within 12” (30.5 cm) side clearance, wall cabinets no deeper than 13” (33...

9 Minimum clearances from adjacent combustible construction: Below cooking surface (36” [91.4 cm] and below) • Sides - 0” • Top grate support - 36” (91.4 cm) Above cooking surface (above 36” [91.4 cm]) • Sides - 12” (30.5 cm)• Within 12” (30.5 cm) side clearance, wall cabinets no deeper than 13” (33...

10 Clearance Dimensions (Proximity to Cabinets) 58” min. (147.3 cm) 13” max. ( 33.0 cm) 12” min. (30.5 cm) 18” min. (45.7 cm) 3/8” (0.95 cm) 36” (91.4 cm) A Range Width “A” Dimension 36” 36” (91.4 cm) 48” 48” (121.9 cm) • This range may be installed directly adjacent to existing 36” (91.4 cm) high b...

12 Electrical Requirements - Gas Ranges /Rangetops Check your national and local codes regarding this unit.This range requires 120VAC/60 Hz; 4 ft. (121.9 cm), 3-wirecord with grounded 3-prong plug attached to unit. See “Electrical Connection” section for grounding instructions. Must be fused seperat...

4” (10.2 cm) 1-1/16” (2.7 cm) 31-1/16” (78.9 cm) Gas or electricalconnection inthis area Gas connection in this area 3-3/4” (9.5 cm) Flexible Connections: If the unit is to be installed with flexible couplingsand/or quick-disconnect fittings, the installer mustuse a heavy-duty AGA design-certified f...

14 READ AND FOLLOW ALL WARNING ANDCAUTION INFORMATION WHEN INSTALLINGTHIS APPLIANCE. • All openings in the wall behind the appliance and in the floor under the appliance must be sealed. • DO NOT obstruct the flow of combustion and ventilation air. Moving, Handling, and Unpacking Remove and discard a...

NOTICE DO NOT use the handle or oven door to lift the oven. Remove door beforeinstallation to ensure that it is not used tolift the unit. DO NOT lift or carry the door by the handle. Removing the door must be done by yourdealer, a qualified licensed plumber, orcertified gas installer. Door Removal 1...

16 Installation - Ranges 1 1 1 2 3 2 2 Legs are packed in cardboard top pack. Note: Legs should be installed near to where appliance is to be used, as they are not secure for long transit. Note: It is strongly recommended that a pallet or lift jack be used rather than tilting. Raise unit about a foo...

17 1 Remove access door. Electrical Connection (3-wire) - Dual Fuel Ranges Note: If you have a 4-wire connection, see following section for 4-wire connection instructions. 2 Remove supply cord strain relief bracket and three supply cord mounting screws on terminal block. WARNING Electrical shock haz...

3 3/ 8” 3/ 8” (0.95 cm) (0. 95 cm ) 3/ 8” (0.95 cm) 4 Move unit into opening. 5 Check that unit is level side to side and front to back. Side trim of the lowest corner must be 3/8” (0.95 cm) above countertop. If leveling is required, move unit out of opening. 6 1 2 1 Lift unit and prop on wood block...

23 Installation - Ranges 1 8-1/2” 8-1 /2” (21.6 cm) (21.6 cm ) 8-1/2” (21.6 cm) Ø 1 /8” Ø 1 /8” (.32 cm) (.32 cm ) Ø 1 /8” (.32 cm) 1-1/2” 1-1/ 2” (3.8 cm) (3.8 cm ) 1-1/2” (3.8 cm) 1 1 2 2 Anti-tip Device Installation (Floor Mount) 2 1 x2 3 1 2 4 Locate anti-tip bracket hook on the floor 8-1/2” (21...

24 1 2 3/ 8” 3/ 8” (0.95 cm) (0. 95 cm ) 3/ 8” (0.95 cm) 3 Slide range into place. Be sure wall anit-tip bracket slides into the anit-tip opening and floor anti-tip hook and bracket are engaged. Final Installation DANGER FIRE HAZARD Backguards come standard with standoff spacers which provide a barr...

When placing the burner head on the burner base, carefully align the locator key in the outer edge below the burner ports with the small notch in the top front edge of the burner base. This will align the burner port with the ignitor. When properly installed, the locator graphic will be aligned with...

26 Final Preparation • All stainless steel body parts should be wiped with hot, soapy water and with a liquidcleaner designed for this material. If buildup occurs, DO NOT use steel wool, abrasive cloths, cleansers, or powders!If it is necessary to scrape stainless steel to remove encrusted materials...

Only authorized replacement parts may be used in performing service on the appliance. All servicing should be referred to a qualified technician. Contact Viking Range, LLC, 1-888-(845-4641), for the nearest service parts distributor in your area orwrite to: VIKING RANGE, LLC PREFERRED SERVICE 111 Fr...

Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-(845-4641) or visit vikingrange.com 066425-000A EN (093018)