Vermont Casting H33BDVRRNP - Manuals

5 Pyromaster © H33BDVRRN/P 10004798 Appliance Top.............................................. 0” (0 mm)Bottom........................................ 0” (0 mm)Side............................................ 0” (0 mm)Back........................................... 0” (0 mm) VentingConcentric secti...

6 Pyromaster © H33BDVRRN/P 10004798 Noncombustible materials such as brick or tile may beextended over the edges of the face of the fireplace.DO NOT cover any vent or grille panels. If a Trim Kit is going to be installed on the fireplace, thebrick or tile will have to be installed flush with theedge...

7 Pyromaster © H33BDVRRN/P 10004798 Installation 1. Thread the wiring through the holes on the end panels of the fireplace. Take care not to cut the wireor insulation on metal edges. Route the wire to aconveniently located receptacle box. 2. Attach the wire to the ON/OFF switch and install the switc...

8 Pyromaster © H33BDVRRN/P 10004798 V V V V V V V X X X D E B B B C B M B A J K F L VENT TERMINATION AIR SUPPLY INLET AREA WHERE TERMINAL IS NOT PERMITTED H I Fixed Closed Fixed Closed Operable Operable Fixed Closed V B INSIDE CORNER DETAIL V A G V N N V V G G A CFM145a General Venting Information -...

9 Pyromaster © H33BDVRRN/P 10004798 Outside Corner Inside Corner Termination Clearances Termination clearances for buildings with combustible and noncombustible exteriors. A =Combustible 6"(152mm) Noncombustible 2"(50mm) B =Combustible 6"(152mm) Noncombustible 2"(50mm) A Balcony - wi...

10 Pyromaster © H33BDVRRN/P 10004798 Twist Lock Pipes When using CFM Corporation twist-lock pipe it is notnecessary to use sealant on the joints. The only areasof the venting system that need to be sealed with hightemperature silicone sealant are the collars on thefireplace and termination, and the ...

11 Pyromaster © H33BDVRRN/P 10004798 STEP 1 Locate vent opening on the wall. To locate hole centerconsult with appropriate fireplace dimensions, Page 4.Frame as shown below. Combustible Walls: Cut a 10 ³⁄₈ ”H (264 mm) x 9 ³⁄₈ ” W (240 mm) hole through the exterior wall and frame asshown. (Fig.13) No...

12 Pyromaster © H33BDVRRN/P 10004798 STEP 5 Guide the vent termination 4” collar into the 4” pipethen the 7” collar into the 7” pipe. Do not force theventing into position. If the pipes do not line up with thetermination collars, disassemble pipes and reattach tothe fireplace collar. (Fig. 16) STEP ...

13 Pyromaster © H33BDVRRN/P 10004798 Vertical Sidewall Installations Example: According to the chart the maximumhorizontal vent length in a system with a 7.5'vertical rise is 20' (6 m) and if a 90 ° elbow is required in the horizontal vent it must be reduced to17' (5.2 m). In Figure 20 Dimension A p...

14 Pyromaster © H33BDVRRN/P 10004798 STEP 2 Measure wall thickness and cut adjustable zero clear-ance sleeve parts to proper length (MAXIMUM 12”/305mm). (Fig. 22) Adjust sleeve to minimum (9 ³⁄₈ ” x 9 ³⁄₈ ”) and attach to firestop with #8 sheet metal screws(supplied). Assemble sleeve and attach to f...

15 Pyromaster © H33BDVRRN/P 10004798 Below Grade Installations Do not back fill around snorkel. Aclearance of at least 4” (100mm) must bemaintained between the snorkel and thesoil. STEP 6 Apply high temperature sealant to 4” (100 mm) and 7”(175 mm) collars or the termination one inch away fromthe cr...

17 Pyromaster © H33BDVRRN/P 10004798 If there is room above ceiling level,firestop spacer must be installed on boththe bottom and the top side of the ceilingjoists. If an attic is above ceiling level a7DVAIS (Attic Insulation Shield) must beinstalled. (Fig. 31) The enlarged ends of the vent sectiona...

18 Pyromaster © H33BDVRRN/P 10004798 Twist Lock Venting Components 7TDVRVT-Through the wall Rear Vent Termination Starter Kit-Model7TDVSK-Sidewall VentingStarter Kit-Model 7TDVSKV-Vertical Venting for 7TDVSKV-A order 1/12 to 6/12 roof pitchfor 7TDVSKV-B order 7/12 to 12/12 roof pitchfor 7TDVSKV-F or...

19 Pyromaster © H33BDVRRN/P 10004798 Crimped End Venting Components 7TDVRVT-Through the wall Rear Vent Termination Starter Kit-Model 7TDVSK-Sidewall VentingStarter Kit-Model 7TDVSKV-Vertical Venting for 7TDVSKV-A order 1/12 to 6/12 roof pitchfor 7TDVSKV-B order 7/12 to 12/12 roof pitchfor 7TDVSKV-F ...

20 Pyromaster © H33BDVRRN/P 10004798 Only glass approved by the CFMCorporation should be used on thisfireplace. The top louvre panel isremoved by lifting thepanel vertically and pullingit away from the appliance.(Fig. 35) The lower accessdoor is hinged along thebottom edge and is foldeddown to allow...

21 Pyromaster © H33BDVRRN/P 10004798 For units equipped with ‘HI/LO’ valves the flameadjustment is accomplished by rotating the ‘HI/LO’adjustment knob located near the center of the gascontrol valve. (Fig. 38) It is important to periodically perform a visual check ofthe pilot and burner flames. Comp...

22 Pyromaster © H33BDVRRN/P 10004798 3. Open control access panel.4. Push in gas control knob slightly and turn clockwise to "OFF". Do not force. 5. Close control access panel. 1. STOP! Read the safety information above.2. Turn off all electrical power to the fireplace.3. For MN/MP/TN/TP app...

23 Pyromaster © H33BDVRRN/P 10004798 Troubleshooting – Honeywell VS8421 START CHECK Remove Glass Doors Before Service Work GAS SUPPLY ON ▼ ▼ ▼ ▼ ▼ PILOT LIGHTS WITHPIEZO IGNITOR • Lockout Has Engaged. Wait 60Seconds And Try Again. • For Spark At Electrode WhileDepressing Piezo1/8" Gap To Pilot H...

24 Pyromaster © H33BDVRRN/P 10004798 This unit is factory setup for use with natural gas. The conversion of this appliance fromnatural gas to propane gas must becarried out by an authorized serviceprovider. LP Conversion Kit Components (Supplied with unit.) Description Part # Pilot Orifice #35 10002...

25 Pyromaster © H33BDVRRN/P 10004798 Maintenance Burner and Burner Compartment It is important to keep the burner and the burnercompartment clean. At least once per year the logs andlava rock/ember material should be removed and theburner compartment vacuumed and wiped out. Removeand replace the log...

26 Pyromaster © H33BDVRRN/P 10004798 LO HI PILOT ADJ PILOT ON OFF 2 3a/b 1 1a 1b 1c 4 5 6 7 8 9a/b 11 12 13 17 14 15 16 18 10 4758 CFM Harris Systems reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. H33BD...

28 Pyromaster © H33BDVRRN/P 10004798 FK24 Fan Assembly This auxiliary fan system increases the efficiency of thecirculation of the heated air. The FK24 fan kit allows variable speed control of thecirculation fan and also incorporates a heat sensor inthe circuit. Specifications 115 Volts / 60Hz / 56 ...

29 Pyromaster © H33BDVRRN/P 10004798 The fireplace, when installed, must beelectrically connected and grounded inaccordance with local codes or, in theabsence of local codes, with the currentCSA C22.1 Canadian Electric Code. For USA installations follow the localcodes and the national electrical cod...

30 Pyromaster © H33BDVRRN/P 10004798 Do not remove the existing window frameassembly. Top Louvre Bay WindowFrame BottomBrassTrim BottomLouvreAssemblies Spacers CeramicRefractory Screws FP1195 Fig. 47 Bay window installation. CeramicRefractory Decorative Bay Windows 4. Lay the angular base panels in ...

31 Pyromaster © H33BDVRRN/P 10004798 Optional remote control units are available to controldifferent functions of the appliances. Model Function(s) Controlled RM4 ON/OFF w/batteries Remote Controls Bay Window Screen A Bay Window Screen Kit is available for theH33BDVRRN/P. Do not remove existing wind...

BASIC WARRANTY:CFM Harris Systems (hereinafter referred to collectively as the "Company")warrants that your new Pyromaster Gas Appliance is free from manufacturingand material defects for a period of one year from date of installation, subjectto the following conditions and limitations. EXTE...