Vermont Casting DVT38IN - Manuals

5 Chateau™ 20011956 Rough Opening Width ����� " (1114 mm) Rough Opening Height Rough Opening Depth 37 ��� " (962 mm) ����� " (876 mm) 54" (1372 mm) 76 ��� " (1 94 0 m m) 8 ��� " Dia. (213 mm) 11" Dia. (279 mm) 49 ��� " (1257 mm) 33 ��� " (848 mm) 2 ��� " (60 m...

6 Chateau™ 20011956 A) Flat on wall B) Cross corner C) **Island D) *Room divider E) *Flat on wall corner F) Chase installation Y) 6” minimum NOTE (Fig. 3): ** Island (C) and Room Divider (D) installation is possible as long as the horizontal portion of the vent system (X) does not exceed 20’ (6 m). ...

7 Chateau™ 20011956 A hearth is not mandatory but is recommended for aesthetic purposes. We recommend a noncombustible hearth which projects out 12” (305 mm) or more from the front of the fireplace. The hearth cannot exceed 1 ¹⁄₂ ” (38mm) in height from bottom of fireplace for ease of door accessibili...

8 Chateau™ 20011956 Gas Inlet and Manifold Pressures Natural LP (Propane) Minimum Inlet Pressure 5.5” w.c. 11.0” w.c. Maximum Inlet Pressure 14.0” w.c. 14.0” w.c. Manifold Pressure 3.5” w.c. 10.0” w.c. High Elevations Input ratings are shown in BTU per hour and are certified without deration for elev...

9 Chateau™ 20011956 Control System The gas control system is located on the right hand side of the firebox behind an access panel and the decora-tive brick panel. The fireplace is operated using only the hand held remote control unit. The system wiring diagram is shown in Figure 11. NOTE: If you choos...

10 Chateau™ 20011956 ���������������������� ADJ. S Remote/Off IPI POWER AUX Learn I Continous Pilot Off/On Junction Box Main Module FP1792 Fig. 11 Connect 120V AC electrical supply. Main Module Learn Button Power Module cover in place. Carefully remove the circuit board. Install batteries with dimpl...

11 Chateau™ 20011956 Hand-Held Remote Control Transmitter Operating Instructions Introduction This transmitter operating range is approximately 20 feet (6 m). The transmitter operates on one of 1,048,576 security codes that are programmed into the transmitter at the factory; this transmitter operate...

12 Chateau™ 20011956 ����� ���� ��� ���� ���� ���� ���� ���� ���� ��� FP1820F-C display9/07 Screen while de-pressing ON key Screen while de-pressing OFF key Screen after 3 sec-ond default Screen after 3 sec-ond default Screen whild de-pressing OFF key Screen after 3 second default Screen after de-pr...

13 Chateau™ 20011956 ���� ��� FP1821set temp9/07 ���� ��� ���� ���� ���� ���� ���� ���� ����� To Change the Set Temperature Press and hold the SET key until the desired set tem-perature is reached. (By pressing and holding the set key, the LCD screen set numbers will increase from 45° to 99°, then r...

14 Chateau™ 20011956 Operational Notes: The Thermostatic feature on the transmitter operates the appliance whenever the ROOM TEMPERATURE varies a certain number of degrees from the SET TEMPERATURE. This variation is called the “SWING” or TEMPERATURE DIFFERENTIAL. The normal operating cycle of an app...

15 Chateau™ 20011956 General Venting Your fireplace is approved to be vented either through the side wall, or vertical through the roof. • Only CFM Corporation venting components spe-cifically approved and labelled for this fireplace may be used. • Venting terminals shall not be recessed into a wall or...

16 Chateau™ 20011956 V V V V V V V X X X D E B B B C B M B A J K F L VENT TERMINATION AIR SUPPLY INLET AREA WHERE TERMINAL IS NOT PERMITTED H I ����� ������ ����� ������ �������� �������� ����� ������ V B CFM145a DV Termin Location 5/01/01 Rev. 12/05/01 sta INSIDE CORNER DETAIL V A G V N N V V G G A...

17 Chateau™ 20011956 Fig. 14 Termination clearances. Quick Reference for Fresh Air Restrictor Plate / Flue Baffle Application Item DVT38N DVT38P DVT44N DVT44P SK8DVSK Flue Restrictor Plate 3” None None 4 ¹⁄₂ ” Fresh Air Restrictor Plate None None None #1 Vertical Less than 12’ Flue Restrictor Plate N...

18 Chateau™ 20011956 Horizontal Termination The vent must rise vertically a minimum of 24” (610mm) off the top of the unit, before the first elbow. The hori-zontal run may extend up to 20’ (6 m) and include a ver-tical rise of up to 40’ (12 m). (Fig. 16) Horizontal termi-nation must also meet the cri...

19 Chateau™ 20011956 Sidewall Applications ������������������������� ������ ��� � � � � � � � � � �� �� �� �� �� �� �� �� �� �� �� Vertical Run (in feet) (Measured from the appliance flue collar to the top of the vent pi pe.) Horizontal Run (in feet) �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �...

20 Chateau™ 20011956 • The maximum number of 45° elbows permitted per side wall installation is two (2). These elbows can be installed in either the vertical or horizontal run. (Fig. 19) • For each 45° elbow installed in the horizontal run, the length of the horizontal run MUST be reduced by 18” (45...

21 Chateau™ 20011956 STEP 3 Slide the zero clearance sleeve through the wall and install the firestop on the inside surface of the wall. Secure with four (4) #8 sheet metal screws. STEP 4 Place fireplace into position. (Fig. 23) Measure the ver-tical height (X) required from the base of the flue collar...

22 Chateau™ 20011956 FP1243a Fig. 26 Secure termination to wall. Use of Restrictor Plate for Vertical Venting Applications The primary purpose for the vent restrictor is to regain flame height under certain venting conditions as outlined below. NOTE: The joints of the inner pipe (flue pipe) must be ta...

23 Chateau™ 20011956 Max. 20' (6 m) Max. Height 40' (12 m) Min. Height 20' (6 m) FP1244a through the roof max/min dims 4/03 Pipe Straps Every 3’ (914mm) FP1244a Fig. 29 Support straps for horizontal runs. • Up to two (2) 30° or 45° elbows may be used within the horizontal run. For each 30° or 45° el...

24 Chateau™ 20011956 FP593 SR/C 11/20/97 Attic Installation Ceiling Installation Nails (4) Firestop Spacer Joist Joist Firestop Spacer Nails (4) FP593 Fig. 31 Installing firestop spacer. FP263 MBUF 5/9/96 Attic Insulation Shield Ceiling Base Flanges Nails (4 Re- quired) Attic Joist FP263 Fig. 32 Atti...

25 Chateau™ 20011956 Chimney Components Horizontal Starter Kit Contains 24”-40” telescopic pipe* for minimum vertical SK8DVSK rise from collar pipe, 90° elbow, horizontal through-wall starter pipe, zero clearance sleeve, metal adhesive tape, stove cement tube, sidewall termination and firestop. SK8 C...

26 Chateau™ 20011956 Only glass approved by CFM Corporation should be used on this fireplace. 1. Turn the fireplace OFF (including the pilot).2. If the unit has been operating allow time for the components to cool. 3. Using a Phillips screwdriver, unfasten two (2) screws located at the top of the glas...

27 Chateau™ 20011956 6. Replace the rear lower and upper refractory, side refractory, fettle, andiron, logs and glass. FP1556 remove rear log bracket 3/05 djt Rear Log Bracket Remove Screws (3) Fig. 37 Remove rear log bracket. FP1556 FP1558 fresh restrictorplate adjustment3/05 djt 1 2 3 4 Fresh Air ...

28 Chateau™ 20011956 3. Start with either the right side refractory or left side refractory. Hold the refractory at an angle. Slide and seat the bottom edge toward the bottom of the firebox. Tilt it carefully toward the side until the piece is in place. Slide the refractory forward until it comes in ...

29 Chateau™ 20011956 �������������������� Log Burner Overlay Log Grate Burner LG401 Figure 43 1. Position the Log Grate Burner. Remove the two (2) screws that attach the fettle to the burner. Place the log grate burner between the notch on the front of the burner housing behind the burner tube. (Fig...

30 Chateau™ 20011956 LG405rear logs3/05 Log Rear Left Log Rear Right LG405 Figure 45 7. Position the Log Grate Right and Left. Position the right and left grate logs simultaneously on the grate in front of the burner housing by hold-ing the two logs with the narrower end toward the middle and the ba...

31 Chateau™ 20011956 LG406Upper logs3/05 Log Rear Upper Middle (DVT44IN Only) Log Front Upper Right Figure 48 LG406 12. Position the Log Front Middle Right. DVT38IN only. Hold the log with the pointed end toward the back and the wide end toward the front. Set the rectangular indentation located on t...

32 Chateau™ 20011956 ������������������� Fig. 49 DVT38IN logset complete. Small Lava Rock Ember Material Volcanic Rock LG484 ������������������� Fig. 50 DVT44IN logset complete. Small Lava Rock Ember Material Volcanic Rock LG482

33 Chateau™ 20011956 ������������������������� It is important to periodically perform a visual check of the pilot and burner flames. Compare them to the illustrations below. (Figs. 51 & 52)If the flame patterns appear abnormal contact a qualified service provider for service and adjustment. Flame ...

34 Chateau™ 20011956 Trim Installation CAUTION: Allow fireplace to cool if it has been in operation. Trim components: Top frame assembly, bottom trim assembly, right and left trim assemblies. NOTE: Place trim pieces with magnets facing window frame.1. Place bottom trim on the bottom of the window fra...

35 Chateau™ 20011956 Lighting & Operating Instructions For Fireplaces equipped with American Flame Automatic Control System (IN or IP) A. This fireplace is equipped with an ignition device which automatically lights the pilot and main burner. The pilot and burner light automatically with the hand...

36 Chateau™ 20011956 Troubleshooting If erratic system behavior is observed that cannot be resolved by the methods outlined below, ensure that there is not a transmitter with batteries installed that may be interfering. If a transmitter is packed with batteries installed, its buttons may be depresse...

37 Chateau™ 20011956 Troubleshooting American Flame Gas Control System (continued) Pilot is burning but ignitor continues to spark • Check that flame sensor is fully inpinged by pilot flame. If not, adjust pilot. • Check end-to-end continuity of sensor. If sensor has continuity, replace module. • Veri...

38 Chateau™ 20011956 American Flame Gas Control System Error Codes Ignition Safety: Protection for Ignition System Error Code: One beep every one second Description of Fault: Warn users if the pilot is not successfully ignited in 60 seconds. How to Clear: Press OFF then ON buttons to re-attempt igni...

39 Chateau™ 20011956 Fuel Conversion Instructions WARNING! This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all appli-cable codes and requirements of the authority having jurisdiction. If the information in these instructions ...

40 Chateau™ 20011956 10. Install the conversion orifice.11. Reinstall pilot hood. Be sure to align hood with index tab. Converting the Gas Control Valve The AF4000 electronic control valve is convertible from natural gas to propane gas by changing the minimum rate screw in the valve and by rotating a...

41 Chateau™ 20011956 Pilot Flame Adjustment Typically, the top 3/8” or 1/2” of the pilot flame sensor should be engulfed in the pilot flame. (Page 33, Fig. 55)To adjust pilot burner:1. Locate pilot adjustment screw on the valve next to the black plastic cap. Refer to Page 35. 2. Adjust pilot screw to ...

42 Chateau™ 20011956 Maintenance Burner and Burner Compartment It is important to keep the burner and the burner compartment clean. At least once per year the logs and lava rock/ember material should be removed and the burner compartment vacuumed and wiped out. Remove and refit the logs as per the in...

44 Chateau™ 20011956 DVT38IN, DVT44IN (continued) Ref. Description DVT38IN DVT44IN 1. Log Set (Complete) 20011953 20011954 1a. Log Grate Right 20011977 (F39) 20011964 (F54) 1b. Log Front Left 20011965 (F32) 20011965 (F32) 1c. Log Front Middle Left 20011966 (F33) 20011966 (F33) 1d. Log Front Upper Ri...

45 Chateau™ 20011956 DVT38IN, DVT44IN (continued) Ref. Description DVT38IN DVT44IN 21. Power Module (DC System Only) 20011901 20011901 22. Glass Frame Assembly 20012242 20012240 23. Glass Assembly 20012243 20012241 24. Pressure Test Adaptor 20012312 20012312 25. Outer Pipe Aluminum Foil Tape 2000616...

46 Chateau™ 20011956 Accessories Ceramic Refractory Kits Ceramic refractory panels are available in kit form for the DVT38IN and DVT44. Fireplace Kit Model Description DVT38IN DVT38CRR Colonial Red DVT38IN DVT38CRL Limestone DVT38IN DVT38CRH Herringbone DVT44IN DVT44CRR Colonial Red DVT44IN DVT44CRL...

47 Chateau™ 20011956 LIMITED LIFETIME WARRANTY CFM Corporation (hereinafter referred to as CFM) warrants that all cast iron parts, the combustion chamber, ceramic burner, and heat exchanger of every Vermont Castings gas product will be free of defective material or workmanship during the period the ...

Efficiency Ratings Model EnerGuide Ratings Fireplace Efficiency (%) DVT38IN 48.2 DVT38IP 48.2 DVT44IN 51 DVT44IP 51 2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3 800-668-5323 • www.cfmcorp.com CFM Corporation