Vermont Casting C34G624M - Manuals

6 MouNTiNG reCoMMeNdATioNs Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. W...

7 V ermont ® CeiliNG brACkeT brACkeT iNsTAllATioN Step 1. Route the outlet box wires through the center hole of the ceiling bracket. Attach the ceiling bracket to the outlet box with the mounting hardware included with the outlet box, ensuring that the outlet box wires are not pinched by the washers...

8 MoTor iNsTAllATioN 2 black Wires 2 White Wires 3 Green Wires Motor hook Motor hook Ceiling bracket loops Figure #1 Figure #2 Ceiling bracket loop Step 2a. Attach one of the hooks on the outside of the motor onto one of the loops hanging from the ceiling bracket as shown in Figure #1. Step 2b. Trim...

9 V ermont ® Figure #3 Step 2c. lift up on the motor, attach the second hook on the outside of the motor onto one of the other loops hanging from the ceiling bracket as shown in Figure #3. Step 2d. After making the wire connections, the wires should be tucked in to the outlet box as shown in Figure ...

10 Step 3a. locate and loosen the two motor housing mounting screws that are located on the side of the ceiling mounting bracket as shown in Figure #1. Step 3b. Install the motor housing by aligning the two slots on the inside of the motor housing with the heads of the two mounting screws that are m...

11 V ermont ® Step 3c. Install the last two of the four motor housing mounting screws holding the motor cover to the ceiling mounting plate as shown in Figure 4. Tighten all four screws until hand tight. Step 3d. Insert the four hole plugs as shown in Figure #5 covering the heads of the screws. The ...

12 blAde PrePArATioN ANd iNsTAllATioN blade irons (5) blade Medallions (5) blades (5) screw Pack C blade screws (21) screw Pack d blade iron screws (11) Step 4a. Attach blade to bladeholder by first pressing the blade badge onto the blade (Pack C), then attaching the bladeholder using the four blade...

13 V ermont ® liGhT FiXTure iNsTAllATioN light kit lightbulb shield socket Plate Glass shade Pack e switch housing Plate screws (3) Pack e socket Plate screws (3) halogen lightbulb liGhT FiXTure hArdWAre (not to scale) Step 5c. Insert the third screw and tighten screws with the provided screw driver...

14 CAUTION: The halogen bulb is very delicate and should n o t b e h a n d l e d w i t h b a r e h a n d s . A f t e r removing it from the box, grasp it gently by the plastic covering or a soft cloth. Step 5d. Remove the ceramic wire nuts from the wires and set aside for use in the next two steps. ...

15 V ermont ® Step 7a. Position the indentations in the outer rim of the glass shade so that they line up with the tabs on the inside surface of the fan light fixture rim. Step 7b. Carefully lift the glass shade up inside the light fixture as far as it will go. Rotate the shade in a clockwise direct...

16 screw 6-32 X 1" (2) screw 6-32 X 3 / 8 " (2) Wood screw 1" (2) drywall Anchor 6-32 (2) 12v battery W-72 Control W-72 Control holder VERSA•TOUCH2® COnTROl InSTAllATIOn CoNTrol brACkeT iNsTAllATioN Standard light Switch Step A. Remove the two screws holding the switch cover plate. do no...

17 send signal led Fan Control To start the fan. Press the selected speed button to run the fan at the desired speed. loW=low speed MEd=Medium speed HIGH=High speed To turn off the fan, press the FAn oFF button. Airflow Direction To reverse the airflow, press the REVERSE button. REVERSE operates at ...

18 If the fan is not functioning after installation: Step 1. Check to make sure that batteries are installed correctly in the control. Step 2. Turn the power off to the fan (from the circuit breaker) for at least 5 seconds. Step 3. Turn the power back on (at the circuit breaker) and push the HIGH, M...

19 V ermont ® Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. TroubleshooTiNG TiPs PRoBlEM PoSSIBlE REMEdIES Fan will not start • Check the main circuit fuses, circuit breakers, and wall switch position. Check all wire connections. Make ...

20 Fan Finishes • For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish.• A vacuum cleaner brush nozzle can remove heavier dust.• Surface smudges or an accumulation of dirt and dust can be removed easily by using a mild detergent and slightly dampened soft clo...

21 V ermont ® ProduCT sPeCiFiCATioNs Model name: Vermont ® Model number: C34GxxM dimensions: A = 9.7" B = 13.7" C = n/A" d = n/A" E = 15.4" Weight: 35 lbs. noTE: dimension B includes light fixture and glass. Motor: 188 x 20mm direct drive™ Blade Span: 54" Blade Iron Pitch: 15...