Vermont Casting 6000 - Manuals

Page 2 - Statement of Commitment; CFM Corporation

Congratulations and thank you for your purchase of your new Great Outdoors grill. We are pleased that you have recognized the value of the design, function, and quality of components used in this product. We believe it is among the finest on the market. We are committed to producing quality products...

Page 3 - Table of Contents; Chapte r 1 - INSTALLATION; Necessary Information; Chapter 2 - ASSEMBLY INSTRUCTIONS

Table of Contents Chapte r 1 - INSTALLATION Necessary Information . . . . . . . . . . . . . . . . . . . . . . . . . . . Choosing a Safe Location . . . . . . . . . . . . . . . . . . . . . . . . . Portable L.P. Gas Grills . . . . . . . . . . . . . . . . . . . . . . . . . . . L.P. Gas Dealer Instructio...

Page 4 - Installation; Chapter; Choosing a Safe Location

· Do not operate this barbecue in garages, breeze ways, sheds or any enclosed area. · · · · · Operating this or any gas-fired appliance in an enclosed area can produce a build-upof carbon-monoxide, which could result ininjury or death. or, in the absence of local codes, with either the National Fuel...

Page 5 - Barbecue Grills

5 The L.P. Fuel Supply System The L.P. Fuel Supply System Hot drippings from cooking food could damage the fuel supply system. Liquid Propane (abbreviated L.P.) gas is stored under high pressure inside a cylinderand will vaporize when released. It isimportant that there are no leaky connectionson th...

Page 8 - Take These Instructions to the L.P. Gas Dealer

Example B Type 1 (cut away to see fitting) Example A CGA-510 POL Filling a Type 1 Cylinder Valve Example A: shows a CGA-510 POL fitting. Example B: shows using a Type 1 POL fitting. The L.P. gas cylinder has a Type 1 cylinder valve with a back-check module in its outletthat will not permit gas to fl...

Page 9 - Assembly Instructions

Getting Started Unpacking the Grill Parts Liquid Propane Models Natural Gas Models 1. Please follow the steps in the order that they are presented. 2. Assemble the grill where you plan to use it.3. You may want to place an old towel or cloth at the assembly site to prevent nuts andbolts from becomin...

Page 10 - Assembly Step 1 - Identifying the Grill Parts

1 0 Assembly Step 1 - Identifying the Grill Parts handlestandoff (2) handle (1) warming rack (1) cast ironcooking grids (1) rock grate (1) side table (2) base (1) 6100 series cylinder retainerwire (1) (2 locking casters and2 non-locking castersInstalled) 8100 series (2) grill lid (1) grill bottomass...

Page 11 - Assembly Step 2; - Attach the Base to the Pillar

Tools Needed: 3/8” wrench 7/16” wrench 1. 2. 3. 4. 5. 11 Assembly Step 2 - Attach the Base to the Pillar Lock the pre-assembled casters on base bypushing down on the latch. Set the pillar upside down. Set the base upside down onto the pillarbottom as shown, aligning the holes in thebase with holes i...

Page 12 - Assembly Step 3; - Attach Grill Bottom to Pillar

1. 2. 3. 12 Assembly Step 3 - Attach Grill Bottom to Pillar Working from the back (open) side of the pillar,set the heat shield on top of the pillar. Set the grill bottom on top of the heat shield. Lineup the burner tubes with the control valve orificesinside the pillar. Adjust the grill bottom and ...

Page 14 - Assembly Step 4; - Attach the Side Tables

14 Assembly Step 4 - Attach the Side Tables 1. 2. 3. USE HARDWARE BAG C : 1/4-20 x 3/4” bolt (8) 1/4-20 hex nut (8) LOCATE THESE PARTS: 7/16” wrench Tools Needed: 3/8” wrench side table (2) Insert the 3/4” boltsthrough the holes inthe support bracketsof the side table. Attach the side tableto the fo...

Page 15 - Assembly Step 5; - Assemble the Grill Lid

15 Assembly Step 5 - Assemble the Grill Lid 1. 2. 3. 4. Place the heat indicator onto the front of thegrill lid, lining up the 3 prongs with the 3mounting holes. From the inside of the lid, secure the heatindicator with the 2 push nuts. Position the back of the lid so that the rearholes are in line ...

Page 17 - Assembly Step 6; - Installing the Internal Grill Parts

17 Assembly Step 6 - Installing the Internal Grill Parts cast ironcooking grids6000 series (1)80 (2) 00 series LOCATE THESE PARTS: rock grate (1) warming rack (1) ceramic briquettes (1 package) 1. 2. Place the single rock grate into the grillbottom. Open the package containing theceramic briquettes ...

Page 21 - Natural Gas Grills - Connecting to Natural Gas

A quick-connect coupling sleeve with 3/8” female end is provided. Install the connectorsocket at the pipe end, after the shut-off valve.This must be installed where the grill will be inuse. It is important to observe the safety guidelines for choosing a safe location. Thegas supply must be shut off ...

Page 24 - Model 6000 Series Components

Model 6000 Series Components 6000 Series Parts 1 PILLAR ASSEMBLY 1 BASE ASSEMBLY 1 quantity consisting of: Natural Gas Model only: consisting of: 1111 pkg 1118112 14121121 1 122 BOTTOM / BURNER ASSEMBLY consisting of: Grill LidRock GrateCast Iron Cooking GridCeramic Briquettes Cast Brass BurnerVentu...

Page 25 - Model 8000 Series Components

Model 8000 Series Components 32 8000 Series Parts 1 PILLAR ASSEMBLY 1 BASE ASSEMBLY 1 quantity consisting of: Natural Gas Model only: consisting of: 1121 pkg 1181 14121121 1 122 BOTTOM / BURNER ASSEMBLY consisting of: 12 Grill LidRock GrateCast Iron Cooking GridsCeramic Briquettes Cast Brass BurnerV...