Tripp Lite SU10KRT3UPM - Manuals

Page 2 - Important Safety Warnings; UPS Location Warnings; temperatures between 62° F and 84° F (between 17° C and 29° C).; UPS Connection Warnings

2 Important Safety Warnings SAVE THESE INSTRUCTIONS. This manual contains important instructions and warnings that should be followed during the installationand maintenance of all Tripp Lite SmartOnline Rackmount UPS Systems and their batteries. UPS Location Warnings • Install your UPS indoors, away...

Page 3 - Mounting; Single Unit Installation

3 Mounting 1 Single Unit Installation 1 2 3 A B C B E D F 4 G Connect the two segments of each shelf (A) using the included screws and nuts (B).Leave the screws slightly loose so that the shelves can be adjusted in the next step. Adjust each shelf to fit your rack, then mount them in the lowest avai...

Page 4 - continued

4 Mounting continued Connect the shelved sections from two UPSRMRII kits (A) to the unshelved sections(B) using the included screws and nuts (C). Note: Two unshelved sections will beleft over. Leave the screws slightly loose so that the shelves can be adjusted in thenext step. Adjust each shelf to f...

Page 5 - Suggested Tower Mount Installation

Mount the shelved sections (A) of your UPSRMRII kit on the back side of your rack.Mount them in the lowest available space of your rack with with the screws, nuts andwashers provided (B). Note that the support ledges should face inward. Attach mounting ears (C) to the front mounting holes of your eq...

Page 6 - Features; UPS Front Panel Controls; alarm is sounding, press this button to silence it.

6 Features Familiarize yourself with the location and function of the front and rear panel features before installing and operating your UPS. UPS Front Panel Controls The UPS Front Panel Controls can be rotated in its mounting to match your tower or rackmount installation. To rotate the controls, in...

Page 7 - Battery Pack Rear Panel

7 Features continued UPS Rear Panel EPO ACC. RS-232 DRY CONTACT AC INPUT AC OUTPUT BREAKER AC INPUT BREAKER EXTERNAL BATTERY INPUT 240VDC CAUTION: DO NOT DISCONNECT UNDER LOAD G L1 L2 L2 L1 G G L1 L2 L2 L1 G AC OUTPUT C US UL Input: 200/208/220/230/240V~, 50/60Hz29.1/27.9/26.4/25.3/24.2A Output: 200...

Page 8 - 4 Overtemperature Reset Breaker:

8 Features continued UPS Rear Panel 1. Output Terminal Block: Use these terminals to connect your UPS to your equipment or to the transformer’s UPS Connector. Unscrew and remove the cover plate above the block for access. 2. Input Terminal Block: Use these terminals to connect your UPS to your utili...

Page 9 - Connection; Installation—No Isolation Transformer

9 Hardwire your utility power source to your UPS’s input. Remove the top of the box covering the UPS’s power terminals. Pass one end of apower cable through the UPS’s cover box’s right knockout, then connect it to theUPS’s input terminals. Connect the other end to your utility power source. Hardwire...

Page 10 - Installation—With Isolation Transformer

10 NORMAL BY PASS Hardwire your isolation transformer’s UPS connector toyour UPS’s input and output. Remove the tops of the boxes covering the UPS’s and transformer’s input and outputterminals. Pass the free end of the isolation transformer’s UPS connector throughthe UPS’s cover box’s knockout, then...

Page 11 - Installation—All Applications

11 Connection continued Connect external battery pack(s) to your UPS Your UPS has no internal batteries and must be connected to at least one externalbattery pack to operate. Complete installation and mounting instructions for yourbattery pack(s) appear in the battery pack(s)’s owner’s manual. Make ...

Page 12 - Turn input to the UPS ON; Turn the UPS’s Input Circuit Breaker ON.; Configure your UPS’s output.; Your UPS will autoselect 50 or 60 Hz to match the input.; To turn the UPS and transformer OFF.

12 Turn input to the UPS ON If the UPS is connected to a transformer, turn the transformer’s UPS and LoadBreakers ON. Turn the UPS’s Input Circuit Breaker ON. Press the UPS’s ON button until you hear a beep to begin inverter operation. If your AC input is not providing power normally, you may “cold ...

Page 13 - Operation; STARTED WITH

13 DIAGNOSTIC MODE AC/DC OK DIAGNOSTIC MODE TESTING INVERTER ON BATTERY MODE LOAD = XXX% X.XXKW Operation When you turn the UPS ON, it will enter Diagnostic Mode and perform a brief self-test lasting about 15 seconds. The results of the self-testare shown on the LCD screen in the sequence below. DIA...

Page 14 - if AC power is interrupted.; To silence the On Battery Alarm, press the “ON/MUTE” button.; Normal Operation

14 Operation continued During normal operation, the first line of your LCD Display shows which operating mode your UPS is in: Online, Economy, On Battery,or Bypass. Online mode: The UPS provides AC power while utility power is available and switches to On Battery mode instantly (zero transfer time) ...

Page 16 - Service/Warranty and Insurance; Service

16 Service/Warranty and Insurance Your SmartOnline UPS is covered by the 2-year limited warranty period described below. A variety of service contracts is also availablefrom Tripp Lite, including start-up service contracts and 3- to 5-year SafeSure on-site service contracts. For more information, ca...

Page 17 - Specifications

17 Specifications Specifications are for UPS, Isolation Transformer, and one battery pack. Model SU6000RT3U SU10KRT3U Input UPS Input Voltage 156V~276V Single Phase 156V~276V Single Phase Transformer Input Voltage 200/208/220/230/240V 200/208/220/230/240V Input Frequency 50/60 Hz ± 3 Hz 50/60 Hz ± 3...