Tripp Lite SU10K - Manuals - manualsarea.com

Page 2 - Safety; UPS Location Warnings; UPS Connection Warnings; Equipment Connection Warnings; Battery Warnings

2 Safety This manual contains important instructions and warnings that should be followedduring the installation, operation and storage of all Tripp Lite SmartOnline UPSSystems. UPS Location Warnings • Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight. • Install yo...

Page 3 - Control Panels; FRONT PANEL

3 Control Panels Familiarize yourself with the location and function of the front and rear panelfeatures before installing and operating your UPS. 1. “ON/OFF” Switch: This momentary rocker switch turns the UPS System’s inverter ON and OFF. 2. “SELECT” Button: This button performs two functions: it a...

Page 4 - SUBP; Rear Panels

4 SU10KPM SU6K SUBP SU10KBP Rear Panels ON LINEMODEECONOMYMODE ON LINEMODEECONOMYMODE 1 14 3 6 10 11 2 4 5 879 16 15 18 13 5 12 17 1 14 3 6 10 11 2 4 5 8 7 9 16 15 18 13 17 12 2 5 12 5 L1 L2

Page 5 - Remote “Emergency Power OFF” Connector:; REAR PANELS

5 1. Manual Bypass Switch: This red and yellow dial is used in one step of putting the UPS in "BYPASS” mode, which must be done before performing any maintenance on the UPSwith the connected load supported. (See page 12 for step-by-step instructions for goinginto "BYPASS.") While this sw...

Page 6 - Installation

6 INVERTER OPERATION DIP SWITCHSETTINGS (SU10KPM SHOWN) Using a small tool, set the four Inverter Opera-tion DIP Switches (located on the rear panel ofyour UPS, see pg. 4-5 for location) to matchyour input voltage, input frequency anddesired operational mode. Input Voltage Selection (DIP Switches #1...

Page 7 - WIRING SELECTION

7 UPS LOCATION Move your UPS over short distances using its wheels. Stabilize the UPS by releasing thestabilizers on each side of the unit. NOTE: Do not stack the UPS Systems or externalbattery packs. INPUT AND OUTPUT CONNECTION WIRING SELECTION Choose appropriate cabling (depending on current carri...

Page 8 - EXTERNAL BATTERY PACK CONNECTION

8 EXTERNAL BATTERY PACK CONNECTION (SU6K: Optional; SU10K: Required) Since SU6K models contain internal batteries, connecting external battery packs (toextend runtime) is optional. SU10KPM models, however, do not have internal batteriesand require an external battery pack connection to a SU10KBP or ...

Page 10 - OR

10 SELF-TESTING When you turn the UPS ON, it will perform a brief (about 25 second) self-test. See figurebelow for display sequence.* *Note: If starting from battery, the BATTERY LED will be lit and the I/P and BYPASS LEDs will not. The final LCD display in thediagram below appears when the UPS is o...

Page 12 - SWITCHING UPS TO “BYPASS” MODE; SWITCHING UPS TO “NORMAL” MODE; BATTERY CHARGE WARNINGS

12 OPERATION UNDER SHUTDOWN Your UPS will shut down and the LCD will display a message if it detects one of thefollowing conditions. Note: For all conditions, the “Input,” “Output” and “Bypass” LEDswill be illuminated. Condition LCD Display Message Extended Overload (>150%) OVERLOAD 150% SHUT DOW...

Page 13 - Hardware; Communications; AS-400 INTERFACE TABLE

13 RS-232 INTERFACE This female DB9 port connects your UPS via an RS-232 cable to a workstation or serverequipped with Tripp Lite software. The port uses RS-232 communications to report UPSstatus and power conditions. Using this port, Tripp Lite software can monitor andmanage network power and autom...

Page 14 - DRY CONTACT INTERFACE:; DRY CONTACT INTERFACE TABLE; REMOTE EMERGENCY POWER OFF:

14 DRY CONTACT INTERFACE: This female DB9 contact-closure port allows your UPS to send contact-closure signalsto indicate that it is on battery back-up mode and if its batteries are running low. Theport can also receive a remote shutdown signal. Pin assignment: DRY CONTACT INTERFACE TABLE UPS Operat...

Page 15 - Service; Warranty & Insurance; -Year Limited Warranty

15 Service Service Your SmartOnline UPS is covered by the 2-year limited warranty period describedbelow. A variety of service contracts is also available from Tripp Lite, including start-up service contracts and 3- to 5-year SafeSure on-site service contracts. For moreinformation, call Tripp Lite Cu...

Page 16 - unction Block Diagram

16 F unction Block Diagram LEDS LCD TO RS-232 AS-400 DRY CONT ACT ACCES SORY SL OT REPO AC INPUT BREAKER AC INPUT SURGE PROTECTOR INPUT FIL TER AC TO DC CONVERTER DC TO AC INVERTER ST A TIC BY P A S S SWITCH OUTPUT FIL TER MANU AL BY P A S S SWITCH OUTPUT ISOLA TION XFM OUTPUT BREAKER OUTPUT TERMINA...

Page 17 - Specifications

17 Specifications (Note: Excluding isolation transformer) Model SU6K SU10K Input Input Voltage 156V~280V Single Phase 156V~280V Single Phase Input Frequency 50/60 Hz ± 3 Hz 50/60 Hz ± 3 Hz (selectable, pg. 7) (selectable, pg. 7) Input Current 32A 50A Inrush Current <150A <200A Power Factor (Fu...