Page 2 - blackout or other power interruptions.; SAVE THESE INSTRUCTIONS; Important Safety Instructions
UPS Location Warnings • Install your UPS indoors, away from excess moisture or heat, conductive contaminants, dust or direct sunlight. • For best performance, keep the indoor temperature between 32º F and 104º F (0º C and 40º C). • Leave adequate space around all sides of the UPS for proper ventilat...
Page 3 - If; Rack Mounting; Installation; Tower Mounting
Mount your equipment in either a 4-post or 2-post rack or rack enclosure. The user must determine thefitness of hardware and procedures before mounting. If hardware and procedures are not suitable for yourapplication, contact the manufacturer of your rack or rack enclosure. The procedures described ...
Page 4 - Connection and Start-Up; Plug your equipment into your UPS.; • Press the “ON/TEST” Button; Optional Connections
Important Safety Instructions Connection and Start-Up Plug your UPS’s line cord into anelectrical outlet. Your UPS must be connected to a dedicated circuit ofsufficient amperage. Note, however, that the selectmodels may be fitted with different plug types. Referto the “OP Rating/ Plug Rating” chart ...
Page 5 - Use the included USB cable (see; External Battery Connection
5 Optional Connections (continued) USB and RS-232 SerialCommunications Use the included USB cable (see ) and/or DB9 serial cable (see ) to connect the UPS to a Media Center PC, home automation system or server.Install the Tripp Lite PowerAlert Softwareappropriate to your equipment's operating system...
Page 6 - Front Panel Switches; This switch controls four separate UPS functions:; Front Panel Indicator Lights; Basic Operation
Front Panel Switches “ON/TEST” Button: This switch controls four separate UPS functions: UPS Power ON To turn the UPS on, press this button, hold it for several seconds until you heara beep, then release it. The “ON LINE” LED will illuminate. UPS Self-Test During normal on-line operation, press this...
Page 7 - “LOAD ACTIVE METER” LED:
7 Front Panel Indicator Lights continued “BYPASS” LED: This yellow light will flash to indicate that the UPS’s DC/AC inverter is deactivated and the UPS is in the “Bypass” mode. Duringnormal operation this LED will light briefly when the unit is plugged in, but ifan internal fault or overload occurs...
Page 8 - Rear Panel; External Battery Pack Connector (configuration varies by model):
Rear Panel “REPLACE BATT” LED: This red light will illuminate constantly and the UPS alarm will beep every 2 seconds if your UPS’s microprocessor detects abattery fault or if your UPS fails the automatic self-test (after you turn yourUPS ON) and the UPS battery is less than fully charged. Let the UP...
Page 9 - Phone/Network Line Surge Suppression Jacks:; Communications
9 Rear Panel continued AC Receptacles (Varied by Model): These 15-, 20- and 30-amp receptacles provide your connected equipment with pure sine-wave AC output from theAC line during normal operation and from battery power during blackouts andsevere brownouts. Power provided at these outlets is filter...
Page 10 - Troubleshooting
The UPS’s control panel lights will turn on in the sequences below to signal that the UPS is havingoperational difficulties. Lights (On/Flashing) and Condition Solution On: REPLACE BATT Let the UPS system charge for at least 12 hours Condition: Replace Battery and perform a self test using the "...
Page 11 - Solution; Battery Replacement; Add Batteries; Procedure
11 Troubleshooting (continued) Lights (On/Flashing) and Condition Solution On: FAULT, 25% Restart the UPS. If the problem persists, Flashing: LINE contact Tripp Lite for repairs. Condition: No Output due to HighBus Voltage and Abnormal Input On: FAULT Restart the UPS. If the problem persists, Flashi...
Page 12 - Storage and Service; Storage; Warranty Registration
Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You'll be automatically entered into adrawing for a chance to win a FREE Tripp Lite product!* * No purchase necessary. Void where prohibited. Some restrictions apply. See website for details. Regulatory ...
Page 13 - LEA SU INSTRUCTIVO
Condiciones para la Póliza de Garantía en México Estas condiciones para México sustituyen cualquier versión anterior que pueda haber aparecido en lasección en español de su manual de usuario. LEA SU INSTRUCTIVO CONSULTE SUS CONDICIONES DE GARANTÍA POR PRODUCTO PÓLIZA DE GARANTÍA Este equipo marca Tr...