Smeg SAI3644B - Manuals

Instructions 7 EN • Use cables that can withstand temperatures of at least 90 °C. • The tightening torque of the screws of the terminal supply wires must be 1.5 - 2 Nm. • The power cable must only be installed or replaced by a qualified technician. For this appliance • If cracks or fissures form, or...

Instructions 8 • Let the cooking surface cool down before closing the cover. • People who have pacemakers or other similar devices fitted must make sure that the operation of these devices is not affected by the induction field, the frequency range of which is between 20 and 50 kHz. • In conformity ...

Instructions 9 EN 1.6 Disposal This appliance conforms to the WEEE European directive (2012/19/EU) and must be disposed of separately from other waste at the end of its service life. The appliance does not contain substances in quantities sufficient to be considered hazardous to health and the envir...

Instructions 10 1.7 How to read the user manual This user manual uses the following reading conventions: 1. Sequence of instructions for use.• Standalone instruction. Instructions General information on this user manual, on safety and final disposal. Description Description of the appliance and its ...

Description 11 EN 2 Description 2.1 General Description 60 cm SX = Left cooking zones CNT = Centre cooking zones DX = Right cooking zones 2.2 Control panel 1 Special functions buttons 2 Timer setting area 3 Cooking zones setting area 4 Scroll bar 5 On/Off button

Description 12 Maximum power consumption table * power levels are approximate and may vary according to the pan used or the settings made. Advantages of induction cooking • Energy saving thanks to the direct transmission of energy to the pan (suitable magnetisable cookware is required) compared to t...

Use 13 EN 3 Use 3.1 Instructions 3.2 Preliminary operations In order to remove any moisture that could have accumulated during the manufacturing process and for the electronic circuits and control keypad to work properly:1. Remove the protective films from the external surfaces of the appliance and ...

Use 14 Switching on the hob for the first time When the appliance is used for the first time, after having been connected to the mains the flashing symbol appears on the display. It is used to access the appliance’s technical menu and is intended only for Technical Support personnel. List of symbols...

Use 15 EN Suitable cookware: • Enamelled steel cookware with thick bases. • Cast iron cookware with an enamelled base. • Cookware in multilayer stainless steel, ferritic stainless steel and aluminium with a special base. Unsuitable cookware: • Copper, stainless steel, aluminium, fireproof glass, woo...

Use 16 Advice on energy-saving • The diameter of the base of the pan must not exceed the width of the silk-screened cooking zone. • Pans must not be placed outside the perimeter of the hob or above the front control panel. • When buying a pan, check whether the diameter indicated is that of the base...

Use 17 EN Switching on the cooking zone automatically After switching on the hob:• Position a pan (suitable for induction cooking and not empty) on the cooking zone you wish to use. • The button corresponding to the zone on which the container has been placed turns on automatically and displays . Th...

Use 18 Quick selection After switching on the hob and having selected a cooking zone:1. Place a finger on the scroll bar at approximately the required power level. 2. Move your finger to the left or right to select the required cooking power. Booster Function After switching on the hob and having se...

Use 19 EN The Booster function can be activated quickly.• After switching on the hob, place your finger at the far right of the scroll bar of the cooking zone you wish to use. Double Booster Function The Double Booster function allows more power to be supplied compared to the Booster function.After ...

Use 20 The same parameters are set on both cooking zones. If a large, oval or oblong pan is being used, make sure that it is placed in the centre of the cooking zone. Example of correct pan position Example of incorrect pan position Examples of griddle position To deactivate the Multizone function: ...

Use 21 EN Cooking guidelines The table below shows the power values which can be set, together with the corresponding type of food. Settings may vary depending on the amount of food and consumer taste. Residual heat If the cooking zone is still hot after being switched off, the symbol will be displa...

Use 22 Pause function To activate the Pause function:1. Switch on at least one cooking zone. 2. Hold down the pause button . appears on the displays of all the cooking zones. To deactivate the Pause function: 1. Hold down the button . The pause symbol, which has just been pressed, starts to flash. 2...

Use 23 EN Controls lock This is useful when cleaning the appliance and to prevent functions being activated by mistake.To activate the control lock: • Press the button for at least one second. All the buttons, apart from the and buttons, are locked.To deactivate the control lock: • press the button ...

Use 24 4. When the time elapses, a series of beeps will sound. Press any button to deactivate them. Modifying or deactivating the timer To modify or deactivate the timer during the countdown: 1. Press the On/Off button to activate the hob (if it is in stand-by). • The timer setting area will indicat...

Use 25 EN 3. Use the + and - buttons to modify or reset the timer. 4. After 10 seconds, the timer will start the new countdown or will be deactivated. Recall Function If the appliance is switched off unintentionally, carry out the following procedure within 6 seconds:1. Switch on the appliance. • Th...

Use 27 EN Option U4 modifies the brightness of the display. 10 levels can be selected.• 0 : maximum brightness. • 9 : minimum brightness. Option U5 allows you to display the countdown of the minute minder timer and timed cooking in seconds, from 59 to 0 seconds. • 0 : animation off. • 1 : animation ...

Cleaning and maintenance 28 4 Cleaning and maintenance 4.1 Instructions 4.2 Cleaning the surfaces To keep the surfaces in good condition, they should be cleaned regularly after use. Let them cool first. 4.3 Ordinary weekly cleaning Clean and maintain the hob once a week using an ordinary glass clean...

Cleaning and maintenance 29 EN Changes in colour do not affect the operation and stability of the glass. These are not alterations to the material of the hob but just residues which have not been removed and have then carbonised. Shiny surfaces can form due to the bases of pans, especially aluminium...

Installation 30 5 Installation 5.1 Electrical connection General information Check the grid characteristics against the data indicated on the plate.The identification plate bearing the technical data, serial number and brand name is visibly positioned on the appliance.Do not remove this plate for an...

Installation 31 EN Testing At the end of installation, carry out a brief inspection test. If the hob fails to operate, after checking that you have carried out the instructions correctly, unplug the appliance and contact Technical Support. 5.2 Instructions for the installer • Do not bend or trap the...

Installation 32 5.5 Section cut from the countertop Make a hole in the countertop of the unit according to the dimensions shown in the figure (mm). Dimensions for flush mounting Hob seal To prevent leakage of liquid between the frame of the hob and the countertop, place the adhesive seal provided al...

Installation 33 EN If installed above an oven, a space must be left between the bottom of the hob and the top of the appliance installed below. opens on bottom opens on bottom and on rear On top of an empty kitchen unit or drawers If there are other pieces of furniture (lateral walls, drawers, etc.)...

Installation 34 Ventilation The illustrations below show two examples of installation suitable for proper ventilation and one example of incorrect installation to be avoided. Spring clips To ensure the hob is fixed and centred as accurately as possible, the clips provided must be positioned as descr...